=~=~=~=~=~=~=~=~=~=~=~= PuTTY log 2018.08.27 19:21:40 =~=~=~=~=~=~=~=~=~=~=~= BootROM - 1.73 Booting from SPI flash General initialization - Version: 1.0.0 AVS selection from EFUSE disabled (Skip reading EFUSE values) Overriding default AVS value to: 0x23 Detected Device ID 6820 High speed PHY - Version: 2.0 Init Customer board board SerDes lanes topology details: | Lane # | Speed| Type | ------------------------------| | 0 | 3 | SATA0 | | 1 | 5 | PCIe0 | | 2 | 3 | SATA1 | | 3 | 4 | SGMII2 | | 4 | 5 | PCIe1 | | 5 | 5 | USB3 HOST1 | ------------------------------- PCIe, Idx 0: detected no link PCIe, Idx 1: detected no link High speed PHY - Ended Successfully mv_ddr: mv_ddr-armada-17.06.1-g07f8294 (Aug 11 2017 - 13:12:46) DDR4 Training Sequence - Switching XBAR Window to FastPath Window mv_ddr: completed successfully BootROM: Image checksum verification PASSED __ __ _ _ | \/ | __ _ _ ____ _____| | | | |\/| |/ _` | '__\ \ / / _ \ | | | | | | (_| | | \ V / __/ | | |_| |_|\__,_|_| \_/ \___|_|_| _ _ ____ _ | | | | | __ ) ___ ___ | |_ | | | |___| _ \ / _ \ / _ \| __| | |_| |___| |_) | (_) | (_) | |_ \___/ |____/ \___/ \___/ \__| ** LOADER ** U-Boot 2013.01-02873-g5e4ac3c (Aug 11 2017 - 13:12:40) Marvell version: devel-17.06.0 Board: Rogue-1 SoC: MV88F6820 Rev A0 running 2 CPUs CPU: ARM Cortex A9 MPCore (Rev 1) LE CPU 0 CPU @ 1600 [MHz] L2 @ 800 [MHz] TClock @ 250 [MHz] DDR4 @ 800 [MHz] DDR4 32 Bit Width,FastPath Memory Access, DLB Enabled, ECC Disabled DRAM: 2 GiB MMC: mv_sdh: 0 DBG: Calling spi_flash_probe from env_relocate_spec() SF: Probing bus 0 cs 0 @ 20000000Hz mode 3 SF: Detected N25Q128 with page size 64 KiB, total 16 MiB PCI-e 0: Detected No Link. PCI-e 1: Detected No Link. USB2.0 0: Host Mode USB3.0 1: Host Mode Map: Code: 0x7fedc000:0x7ff975a8 BSS: 0x7ffef600 Stack: 0x7f4cbf20 Heap: 0x7f4cc000:0x7fedc000 U-Boot Environment: 0x00100000:0x00110000 (SPI) Board configuration detected: Net: | port | Interface | PHY address | |--------|-----------|--------------| | egiga0 | RGMII | 0x00 | | egiga1 | RGMII | 0x01 | | egiga2 | SGMII | In-Band | egiga0 [PRIME], egiga1, egiga2 Hit any key to stop autoboot: 3 2 1 0 Reset SCSI AHCI init for unit0 Target spinup took 0 ms. SATA link 1 timeout. Error: SCSI Controller(s) 1B4B:9215 1B4B:9235 not found scanning bus for devices... Device 0: (0:0) Vendor: ATA Prod.: ADATA SU800NS38 Rev: Q051 Type: Hard Disk Capacity: 122104.3 MB = 119.2 GB (250069680 x 512) Found 1 device(s). reading ubldr.bin 229984 bytes read in 11 ms (19.9 MiB/s) ## Starting application at 0x00200000 ... Consoles: U-Boot console Compatible U-Boot API signature found @0x7f4dc280 FreeBSD/armv6 U-Boot loader, Revision 1.2 (Thu May 10 17:00:51 CDT 2018 root@buildbot2.netgate.com) DRAM: 2048MB Number of U-Boot devices: 4 U-Boot env: loaderdev not set, will probe all devices. Found U-Boot device: disk Probing all disk devices... Checking unit=0 slice= partition=...disk0: read failed, error=1 Checking unit=1 slice= partition=... good. Booting from disk1s2a: |/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\console comconsole is invalid! no valid consoles! Available consoles: uboot |/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-/boot/kernel/kernel data=0x11832bc+0x54d44 \|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|syms=[0x4+0x94bc0/-\|/+0x4+0xd439c-\|/-\] Hit [Enter] to boot immediately, or any other key for command prompt. Booting [/boot/kernel/kernel] in 2 seconds... Booting [/boot/kernel/kernel] in 1 second... Booting [/boot/kernel/kernel]... |/-\|/-\|/-\|/-\|/-\|/-/boot/dtb/armada-385-80300-0148-G00-X100.dtb size=0x5307 Loaded DTB from file 'armada-385-80300-0148-G00-X100.dtb'. \|/-Kernel entry at 0x400100... Kernel args: (null) Copyright (c) 1992-2017 The FreeBSD Project. Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994 The Regents of the University of California. All rights reserved. FreeBSD is a registered trademark of The FreeBSD Foundation. FreeBSD 11.1-RELEASE-p10 #0 r313908+9347c667615(factory-RELENG_2_4): Thu May 10 17:03:14 CDT 2018 root@buildbot2.netgate.com:/xbuilder/crossbuild-243/work/armv6/obj/cETt6vGN/arm.armv6/xbuilder/crossbuild-243/pfSense/tmp/FreeBSD-src/sys/pfSense-SG-3100 arm FreeBSD clang version 5.0.1 (tags/RELEASE_501/final 320880) (based on LLVM 5.0.1) CPU: ARM Cortex-A9 r4p1 (ECO: 0x00000000) CPU Features: Multiprocessing, Thumb2, Security, VMSAv7, Coherent Walk Optional instructions: UMULL, SMULL, SIMD(ext) LoUU:2 LoC:2 LoUIS:2 Cache level 1: 32KB/32B 4-way data cache WB Read-Alloc Write-Alloc 32KB/32B 4-way instruction cache Read-Alloc real memory = 2147479552 (2047 MB) avail memory = 2082213888 (1985 MB) SOC: Marvell 88F6820, TClock 250MHz, Frequency 1600MHz Instruction cache prefetch enabled, data cache prefetch disabled FreeBSD/SMP: Multiprocessor System Detected: 2 CPUs iwi_ibss: You need to read the LICENSE file in /usr/share/doc/legal/intel_iwi.LICENSE. iwi_ibss: If you agree with the license, set legal.intel_iwi.license_ack=1 in /boot/loader.conf. module_register_init: MOD_LOAD (iwi_ibss_fw, 0xc0135f78, 0) error 1 iwi_monitor: You need to read the LICENSE file in /usr/share/doc/legal/intel_iwi.LICENSE. iwi_monitor: If you agree with the license, set legal.intel_iwi.license_ack=1 in /boot/loader.conf. module_register_init: MOD_LOAD (iwi_monitor_fw, 0xc0136028, 0) error 1 random: entropy device external interface wlan: mac acl policy registered ipw_bss: You need to read the LICENSE file in /usr/share/doc/legal/intel_ipw.LICENSE. ipw_bss: If you agree with the license, set legal.intel_ipw.license_ack=1 in /boot/loader.conf. module_register_init: MOD_LOAD (ipw_bss_fw, 0xc012c4ec, 0) error 1 ipw_ibss: You need to read the LICENSE file in /usr/share/doc/legal/intel_ipw.LICENSE. ipw_ibss: If you agree with the license, set legal.intel_ipw.license_ack=1 in /boot/loader.conf. module_register_init: MOD_LOAD (ipw_ibss_fw, 0xc012c59c, 0) error 1 ipw_monitor: You need to read the LICENSE file in /usr/share/doc/legal/intel_ipw.LICENSE. ipw_monitor: If you agree with the license, set legal.intel_ipw.license_ack=1 in /boot/loader.conf. module_register_init: MOD_LOAD (ipw_monitor_fw, 0xc012c64c, 0) error 1 iwi_bss: You need to read the LICENSE file in /usr/share/doc/legal/intel_iwi.LICENSE. iwi_bss: If you agree with the license, set legal.intel_iwi.license_ack=1 in /boot/loader.conf. module_register_init: MOD_LOAD (iwi_bss_fw, 0xc0135ec8, 0) error 1 ofwbus0: simplebus0: on ofwbus0 simplebus1: on simplebus0 l2cache0: mem 0x8000-0x8fff on simplebus1 l2cache0: cannot allocate IRQ, not using interrupt l2cache0: Part number: 0x3, release: 0x9 l2cache0: L2 Cache enabled: 1024KB/32B 16 ways gic0: mem 0xd000-0xdfff,0xc100-0xc1ff on simplebus1 gic0: pn 0x390, arch 0x1, rev 0x2, implementer 0x43b irqs 192 mpic0: mem 0x20a00-0x20ccf,0x21870-0x21b6f irq 19 on simplebus1 mp_tmr0: mem 0xc200-0xc21f irq 3 on simplebus1 Timecounter "MPCore" frequency 800000000 Hz quality 800 mp_tmr1: mem 0xc600-0xc61f irq 4 on simplebus1 Event timer "MPCore" frequency 800000000 Hz quality 1000 cesa0: mem 0x90000-0x90fff,0x9d000-0x9dfff irq 1 on simplebus1 cesa1: mem 0x92000-0x92fff,0x9f000-0x9ffff irq 2 on simplebus1 spi0: mem 0x10600-0x1064f irq 5 on simplebus1 twsi0: mem 0x11000-0x1101f irq 7 on simplebus1 iicbus0: on twsi0 iic0: on iicbus0 gpio0: at addr 0xc0 on iicbus0 device_attach: gpio0 attach returned 6 gpio0: at addr 0xce on iicbus0 gpiobus0: on gpio0 gpioc0: on gpio0 gpio1: at addr 0xc0 on iicbus0 device_attach: gpio1 attach returned 6 uart0: <16550 or compatible> mem 0x12000-0x120ff irq 9 on simplebus1 uart0: console (-1,n,8,1) uart1: <16550 or compatible> mem 0x12100-0x121ff irq 10 on simplebus1 wdt0: mem 0x20300-0x20333,0x20704-0x20707,0x18260-0x18263 on simplebus1 pmsu0: mem 0x22000-0x22fff on simplebus1 mvneta0: mem 0x30000-0x33fff irq 26 on simplebus1 mvneta0: version is 10 mvneta0: Ethernet address: 00:08:a2:0d:99:d6 miibus0: on mvneta0 ukphy0: PHY 1 on miibus0 ukphy0: none, 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-master, 1000baseT-FDX, 1000baseT-FDX-master, auto mvneta1: mem 0x34000-0x37fff irq 27 on simplebus1 mvneta1: version is 10 mvneta1: Ethernet address: 00:08:a2:0d:99:d7 mdio0: on mvneta1 e6000sw0: on mdio0 e6000sw0: single-chip addressing mode miibus1: on e6000sw0 e1000phy0: PHY 17 on miibus1 e1000phy0: none, 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-master, 1000baseT-FDX, 1000baseT-FDX-master, auto miibus2: on e6000sw0 e1000phy1: PHY 18 on miibus2 e1000phy1: none, 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-master, 1000baseT-FDX, 1000baseT-FDX-master, auto miibus3: on e6000sw0 e1000phy2: PHY 19 on miibus3 e1000phy2: none, 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-master, 1000baseT-FDX, 1000baseT-FDX-master, auto miibus4: on e6000sw0 e1000phy3: PHY 20 on miibus4 e1000phy3: none, 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-master, 1000baseT-FDX, 1000baseT-FDX-master, auto e6000sw0: switch is ready. etherswitch0: on e6000sw0 ehci0: mem 0x58000-0x584ff irq 28 on simplebus1 usbus0: EHCI version 1.0 usbus0 on ehci0 mvneta2: mem 0x70000-0x73fff irq 29 on simplebus1 mvneta2: version is 10 mvneta2: Ethernet address: 00:08:a2:0d:99:d8 miibus5: on mvneta2 ukphy1: PHY 0 on miibus5 ukphy1: none, 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-master, 1000baseT-FDX, 1000baseT-FDX-master, auto rtc0: mem 0xa3800-0xa381f,0x184a0-0x184ab irq 30 on simplebus1 ahci0: mem 0xa8000-0xa9fff irq 31 on simplebus1 ahci0: AHCI v1.00 with 2 6Gbps ports, Port Multiplier supported with FBS ahci0: quirks=0x200010<2CH,MRVL_SR_DEL> ahcich0: at channel 0 on ahci0 ahcich1: at channel 1 on ahci0 armada_thermal0: mem 0xe4078-0xe407b,0xe4074-0xe4077 on simplebus1 sdhci_fdt0: mem 0xd8000-0xd8fff,0xdc000-0xdc0ff,0x18454-0x18457 irq 34 on simplebus1 sdhci_fdt0: 1 slot(s) allocated xhci0: mem 0xf8000-0xfbfff,0xfc000-0xfffff irq 36 on simplebus1 xhci0: 32 bytes context size, 32-bit DMA usbus1 on xhci0 pcib_ctrl0: on simplebus0 pcib0: on pcib_ctrl0 pci0: on pcib0 pcib1: on pcib_ctrl0 pci1: on pcib1 pcib2: on pcib_ctrl0 pci2: on pcib2 pcib3: on pcib_ctrl0 pci3: on pcib3 cpulist0: on ofwbus0 cpu0: on cpulist0 cpu1: on cpulist0 cryptosoft0: Timecounters tick every 1.000 msec mvneta1: link state changed to UP spibus0: on spi0 mx25l0: at cs 0 mode 0 on spibus0 mx25l0: n25q128, sector 65536 bytes, 256 sectors e6000sw0port1: link state changed to DOWN e6000sw0port2: link state changed to DOWN e6000sw0port3: link state changed to DOWN e6000sw0port4: link state changed to DOWN usbus0: 480Mbps High Speed USB v2.0 usbus1: 5.0Gbps Super Speed USB v3.0 ugen0.1: at usbus0 uhub0: on usbus0 ugen1.1: at usbus1 uhub1: on usbus1 uhub1: 2 ports with 2 removable, self powered mmc0: on sdhci_fdt0 mmcsd0: 8GB at mmc0 50.0MHz/8bit/65535-block mmcsd0boot0: 4MB partion 1 at mmcsd0 mmcsd0boot1: 4MB partion 2 at mmcsd0 mmcsd0rpmb: 4MB partion 3 at mmcsd0 uhub0: 1 port with 1 removable, self powered ada0 at ahcich0 bus 0 scbus0 target 0 lun 0 ada0: ACS-3 ATA SATA 3.x device ada0: Serial Number 2I1820032100 ada0: 600.000MB/s transfers (SATA 3.x, UDMA6, PIO 1024bytes) ada0: Command Queueing enabled ada0: 122104MB (250069680 512 byte sectors) Release APs Trying to mount root from ufs:/dev/diskid/DISK-2I1820032100s2a [rw,noatime]... Configuring crash dumps... No suitable dump device was found. /dev/diskid/DISK-2I1820032100s2a: FILE SYSTEM CLEAN; SKIPPING CHECKS /dev/diskid/DISK-2I1820032100s2a: clean, 29491083 free (667 frags, 3686302 blocks, 0.0% fragmentation) Filesystems are clean, continuing... Mounting filesystems... random: unblocking device. __ _ __ / _|___ ___ _ __ ___ ___ | '_ \| |_/ __|/ _ \ '_ \/ __|/ _ \ | |_) | _\__ \ __/ | | \__ \ __/ | .__/|_| |___/\___|_| |_|___/\___| |_| Welcome to pfSense 2.4.3-RELEASE (Patch 1)... Dump device does not exist. Savecore not run. ...ELF ldconfig path: /lib /usr/lib /usr/lib/compat /usr/local/lib /usr/local/lib/ipsec /usr/local/lib/mysql /usr/local/lib/nss /usr/local/lib/perl5/5.24/mach/CORE Soft Float compatibility ldconfig path: done. External config loader 1.0 is now starting... mmcsd0s1 mmcsd0s2 mmcsd0s2a Launching the init system....... done. Initializing.................. done. Starting device manager (devd)...done. Loading configuration......done. Updating configuration...done. Checking config backups consistency.................................done. Setting up extended sysctls...done. Setting timezone...done. Configuring loopback interface...done. Starting syslog...done. Starting Secure Shell Services...done. Configuring switch...done. Setting up interfaces microcode...done. Configuring loopback interface...done. Creating wireless clone interfaces...done. Configuring LAGG interfaces...done. Configuring VLAN interfaces...done. Configuring QinQ interfaces...done. Configuring WAN interface...done. Configuring LAN interface...done. Configuring OPT1 interface...done. Configuring HEV6 interface...done. Configuring CARP settings...done. Syncing OpenVPN settings...done. route: writing to routing socket: Invalid argument route: writing to routing socket: Invalid argument Configuring firewall......done. Starting PFLOG...done. Setting up gateway monitors...done. Setting up static routes...done. Setting up DNSs...Starting DNS forwarder...done. done. Synchronizing user settings...done. Starting webConfigurator...done. Configuring CRON...done. Starting NTP time client...done. Starting DHCP service...done. Starting DHCPv6 service...done. Configuring firewall......done. Configuring IPsec VPN... done Generating RRD graphs...done. Starting watchdog daemon...done. Starting syslog...done. Starting CRON... done. Starting package apcupsd...done. Starting package AutoConfigBackup...done. Starting package nmap...done. Starting package Service Watchdog...done. Starting package mailreport...done. Starting package Cron...done. Starting package pfBlockerNG...done. Starting package Notes...done. Starting package Shellcmd...done. Starting package suricata...done. Starting /usr/local/etc/rc.d/dnsbl.sh...done. pfSense 2.4.3-RELEASE (Patch 1) arm Thu May 10 15:59:52 CDT 2018 Bootup complete FreeBSD/arm (firewall.home) (ttyu0) login: