https://docs.netgate.com/pfsense/en/latest/solutions/sg-1100/reinstall-pfsense.html General initialization - Version: 1.0.0 AVS selection from EFUSE disabled (Skip reading EFUSE values) Overriding default AVS value to: 0x23 Detected Device ID 6820 High speed PHY - Version: 2.0 Init Customer board board SerDes lanes topology details: | Lane # | Speed| Type | ------------------------------| | 0 | 3 | SATA0 | | 1 | 5 | PCIe0 | | 2 | 3 | SATA1 | | 3 | 4 | SGMII2 | | 4 | 5 | PCIe1 | | 5 | 5 | USB3 HOST1 | ------------------------------- PCIe Ref. Clock Buffer Control is 0xf00015bf, setting to 0xf00015bf SOC_CONTROL_REG1 is 0xf00015bf, setting to 0x0707c0f3 PCIe, Idx 0: detected no link PCIe, Idx 1: detected no link High speed PHY - Ended Successfully mv_ddr: mv_ddr-armada-17.06.1-g07f8294 (Oct 8 2018 - 12:59:22) DDR4 Training Sequence - Switching XBAR Window to FastPath Window mv_ddr: completed successfully __ __ _ _ | \/ | __ _ _ ____ _____| | | | |\/| |/ _` | '__\ \ / / _ \ | | | | | | (_| | | \ V / __/ | | |_| |_|\__,_|_| \_/ \___|_|_| _ _ ____ _ | | | | | __ ) ___ ___ | |_ | | | |___| _ \ / _ \ / _ \| __| | |_| |___| |_) | (_) | (_) | |_ \___/ |____/ \___/ \___/ \__| ** LOADER ** U-Boot 2013.01-02879-geb5cbf6642 (Oct 08 2018 - 12:59:19) Marvell version: devel-17.06.0 Board: Rogue-1 SoC: MV88F6820 Rev A0 running 2 CPUs CPU: ARM Cortex A9 MPCore (Rev 1) LE CPU 0 CPU @ 1600 [MHz] L2 @ 800 [MHz] TClock @ 250 [MHz] DDR4 @ 800 [MHz] DDR4 32 Bit Width,FastPath Memory Access, DLB Enabled, ECC Disabled DRAM: 2 GiB MMC: mv_sdh: 0 DBG: Calling spi_flash_probe from env_relocate_spec() SF: Probing bus 0 cs 0 @ 20000000Hz mode 3 SF: Detected W25Q32JV with page size 4 KiB, total 4 MiB PCI-e 0: Detected No Link. PCI-e 1: Detected No Link. USB2.0 0: Host Mode USB3.0 1: Host Mode Map: Code: 0x7fedc000:0x7ff9741c BSS: 0x7ffef600 Stack: 0x7f4cbf20 Heap: 0x7f4cc000:0x7fedc000 U-Boot Environment: 0x00100000:0x00110000 (SPI) Board configuration detected: Net: | port | Interface | PHY address | |--------|-----------|--------------| | egiga0 | RGMII | 0x00 | | egiga1 | RGMII | 0x01 | | egiga2 | SGMII | In-Band | egiga0 [PRIME], egiga1, egiga2 Hit any key to stop autoboot: 0 reading ubldr.bin ** Unable to read file ubldr.bin ** ## Starting application at 0x00200000 ... General initialization - Version: 1.0.0 AVS selection from EFUSE disabled (Skip reading EFUSE values) Overriding default AVS value to: 0x23 Detected Device ID 6820 High speed PHY - Version: 2.0 Init Customer board board SerDes lanes topology details: | Lane # | Speed| Type | ------------------------------| | 0 | 3 | SATA0 | | 1 | 5 | PCIe0 | | 2 | 3 | SATA1 | | 3 | 4 | SGMII2 | | 4 | 5 | PCIe1 | | 5 | 5 | USB3 HOST1 | ------------------------------- PCIe Ref. Clock Buffer Control is 0xf00015bf, setting to 0xf00015bf SOC_CONTROL_REG1 is 0xf00015bf, setting to 0x0707c0f3 PCIe, Idx 0: detected no link PCIe, Idx 1: detected no link High speed PHY - Ended Successfully mv_ddr: mv_ddr-armada-17.06.1-g07f8294 (Oct 8 2018 - 12:59:22) DDR4 Training Sequence - Switching XBAR Window to FastPath Window mv_ddr: completed successfully __ __ _ _ | \/ | __ _ _ ____ _____| | | | |\/| |/ _` | '__\ \ / / _ \ | | | | | | (_| | | \ V / __/ | | |_| |_|\__,_|_| \_/ \___|_|_| _ _ ____ _ | | | | | __ ) ___ ___ | |_ | | | |___| _ \ / _ \ / _ \| __| | |_| |___| |_) | (_) | (_) | |_ \___/ |____/ \___/ \___/ \__| ** LOADER ** U-Boot 2013.01-02879-geb5cbf6642 (Oct 08 2018 - 12:59:19) Marvell version: devel-17.06.0 Board: Rogue-1 SoC: MV88F6820 Rev A0 running 2 CPUs CPU: ARM Cortex A9 MPCore (Rev 1) LE CPU 0 CPU @ 1600 [MHz] L2 @ 800 [MHz] TClock @ 250 [MHz] DDR4 @ 800 [MHz] DDR4 32 Bit Width,FastPath Memory Access, DLB Enabled, ECC Disabled DRAM: 2 GiB MMC: mv_sdh: 0 DBG: Calling spi_flash_probe from env_relocate_spec() SF: Probing bus 0 cs 0 @ 20000000Hz mode 3 SF: Detected W25Q32JV with page size 4 KiB, total 4 MiB PCI-e 0: Detected No Link. PCI-e 1: Detected No Link. USB2.0 0: Host Mode USB3.0 1: Host Mode Map: Code: 0x7fedc000:0x7ff9741c BSS: 0x7ffef600 Stack: 0x7f4cbf20 Heap: 0x7f4cc000:0x7fedc000 U-Boot Environment: 0x00100000:0x00110000 (SPI) Board configuration detected: Net: | port | Interface | PHY address | |--------|-----------|--------------| | egiga0 | RGMII | 0x00 | | egiga1 | RGMII | 0x01 | | egiga2 | SGMII | In-Band | egiga0 [PRIME], egiga1, egiga2 Hit any key to stop autoboot: 0 Marvell>> ls incorrect device type in spi0=spi_flash invalid mtd device 'spi0.0' mtdparts_init: no valid partitions Marvell>> dir Unknown command 'dir' - try 'help' Marvell>> hep Unknown command 'hep' - try 'help' Marvell>> help 0 - do nothing, unsuccessfully 1 - do nothing, successfully ? - alias for 'help' Creset - Creset - Run 'reset' or boot command in a loop, while counting. SatR - Sample At Reset sub-system active_units- print active units on board base - print or set address offset bdinfo - print Board Info structure boot - boot default, i.e., run 'bootcmd' boot_menu- command allows to select boot script from boot device example: boot_menu bootd - boot default, i.e., run 'bootcmd' bootelf - Boot from an ELF image in memory bootm - boot application image from memory bootp - boot image via network using BOOTP/TFTP protocol bootvx - Boot vxWorks from an ELF image bootz - boot Linux zImage image from memory bubt - bubt - Burn an image on the Boot flash device. chpart - change active partition cmp - memory compare coninfo - print console devices and information cp - memory copy cpss_env- set cpss environment variables permanently crc32 - checksum calculation date - get/set/reset date & time ddrPhyRead- ddrPhyRead - Read DDR PHY register ddrPhyWrite- ddrPhyWrite - Write DDR PHY register dhcp - boot image via network using DHCP/TFTP protocol diskboot- diskboot- boot from IDE device dma - dma - Perform DMA using the XOR engine echo - echo args to console editenv - edit environment variable eeprom - EEPROM sub-system env - environment handling commands exit - exit script ext2load- load binary file from a Ext2 filesystem ext2ls - list files in a directory (default /) ext4load- load binary file from a Ext4 filesystem ext4ls - list files in a directory (default /) ext4write- create a file in the root directory fatinfo - print information about filesystem fatload - load binary file from a dos filesystem fatls - list files in a directory (default /) fdt - flattened device tree utility commands flash_part_print- flash_part_print - print spi/nand FLASH memory information fsinfo - print information about filesystems fsload - load binary file from a filesystem image go - start application at address 'addr' help - print command description/usage i2c - I2C sub-system ide - ide - IDE sub-system iminfo - print header information for application image imxtract- extract a part of a multi-image ir - ir - reading and changing MV internal register values. itest - return true/false on integer compare loadb - load binary file over serial line (kermit mode) loads - load S-Record file over serial line loadx - load binary file over serial line (xmodem mode) loady - load binary file over serial line (ymodem mode) loop - infinite loop on address range ls - list files in a directory (default /) map - map - Display address decode windows md - memory display me - me - PCIe master enable mm - memory modify (auto-incrementing address) mmc - MMC sub system mmcinfo - display MMC info mp - mp - map PCIe BAR mtdburn - Burn a Linux image and Filesystem` on the NAND/SPI flash. mtdparts- define flash/nand partitions mtest - simple RAM read/write test mvsource- mvsource - Burn a script image on flash device. mw - memory write (fill) nfs - boot image via network using NFS protocol nm - memory modify (constant address) pci - list and access PCI Configuration Space pciePhyRead- phyRead - Read PCI-E Phy register pciePhyWrite- pciePhyWrite - Write PCI-E Phy register phyRead - phyRead - Read Phy register phyWrite- phyWrite - Write Phy register ping - send ICMP ECHO_REQUEST to network host printenv- print environment variables pxe - commands to get and boot from pxe files qsgmii_sel- Select SFP or QSGMII modes on bc2/bobk. rcvr - rcvr - Start recovery process (with TFTP server) reset - Perform RESET of the CPU run - run commands in an environment variable saveenv - save environment variables to persistent storage scsi - SCSI sub-system scsiboot- boot from SCSI device se - se - PCIe Slave enable setenv - set environment variables sf - SPI flash sub-system sg - sg - scanning the PHYs status showvar - print local hushshell variables sleep - delay execution for some time smiscan - smiscan - Scan for marvell smi devices. source - run script from memory sp - scan and detect all devices on PCI-e interface sspi - SPI utility command stage_boot- command to load script/image from different devices example: stage_boot hd_img pxe switchCountersRead- switchCntPrint - Read switch port counters. switchPhyRegRead- - Read switch register switchPhyRegWrite- - Write switch register switchRegRead- switchRegRead - Read switch register switchRegWrite- switchRegWrite - Write switch register sys_restore- sys_restore - Search for install script on USB DOK and start installation of linux kernel and rootfs. sysboot - command to get and boot from syslinux files temp - temp - Display the device temperature. tempCmd0- tempCmd - This command allocated for monitor extinction tempCmd1- tempCmd - This command allocated for monitor extinction tempCmd2- tempCmd - This command allocated for monitor extinction tempCmd3- tempCmd - This command allocated for monitor extinction test - minimal test like /bin/sh tftp - boot image via network using TFTP protocol tftpboot- boot image via network using TFTP protocol training- training - prints the results of the DDR3 Training. trainingStability- training - prints the results of the DDR3 Training. ts_report- ts_report - report touch screen coordinate ts_test - ts_test - test touch screen ubi - ubi commands ubifsload- load file from an UBIFS filesystem ubifsls - list files in a directory ubifsmount- mount UBIFS volume ubifsumount- unmount UBIFS volume usb - USB sub-system usbboot - boot from USB device version - print monitor, compiler and linker version whoAmI - - reading CPU ID Marvell>> usbboot ** No device specified ** Marvell>> usb usb - USB sub-system Usage: usb start - start (scan) USB controller usb reset - reset (rescan) USB controller usb stop [f] - stop USB [f]=force stop usb tree - show USB device tree usb info [dev] - show available USB devices usb storage - show details of USB storage devices usb dev [dev] - show or set current USB storage device usb part [dev] - print partition table of one or all USB storage devices usb read addr blk# cnt - read `cnt' blocks starting at block `blk#' to memory address `addr' usb write addr blk# cnt - write `cnt' blocks starting at block `blk#' from memory address `addr' Marvell>> usbboot ** No device specified ** Marvell>> usbboot ? ** No device specified ** Marvell>> usb info USB is stopped. Please issue 'usb start' first. Marvell>> usb start (Re)start USB... USB0: mvBoardUsbVbusSet: gppNo = 35 Port (usbActive) : 1 Interface (usbType = 3) : USB XHCI 1.00 scanning bus 0 for devices... 2 USB Device(s) found scanning usb for storage devices... 1 Storage Device(s) found scanning usb for ethernet devices... 0 Ethernet Device(s) found Marvell>> usbboot ** No device specified ** Marvell>> usbboot usb0 ** No device specified ** Marvell>> usb dev USB device 0: Vendor: PNY Rev: PMAP Prod: USB 2.0 FD Type: Removable Hard Disk Capacity: 29604.0 MB = 28.9 GB (60628992 x 512) Marvell>> usb storage Device 0: Vendor: PNY Rev: PMAP Prod: USB 2.0 FD Type: Removable Hard Disk Capacity: 29604.0 MB = 28.9 GB (60628992 x 512) Marvell>> usb tree USB device tree: 1 Hub (5 Gb/s, 0mA) | u-boot XHCI Host Controller | +-2 Mass Storage (480 Mb/s, 200mA) PNY USB 2.0 FD 071908CF1A2A8D90 Marvell>> boot_menu boot_menu: Environment variable 'boot_source_device' must be defined. Marvell>> run usbrecovery ## Error: "usbrecovery" not defined Marvell>> run usbboot ## Error: "usbboot" not defined Marvell>> setenv bootcmd 'run usbboot' Unknown command 'setenv' - try 'help' Marvell>> usb reset (Re)start USB... USB0: mvBoardUsbVbusSet: gppNo = 35 Port (usbActive) : 1 Interface (usbType = 3) : USB XHCI 1.00 scanning bus 0 for devices... 2 USB Device(s) found scanning usb for storage devices... 1 Storage Device(s) found scanning usb for ethernet devices... 0 Ethernet Device(s) found Marvell>> run usbboot ## Error: "usbboot" not defined Marvell>> run usbrecovery ## Error: "usbrecovery" not defined Marvell>> run usbrecovery ## Error: "usbrecovery" not defined Marvell>> run usbboot ## Error: "usbboot" not defined Marvell>> exit exit not allowed from main input shell. Marvell>>