TIM-1.0
WTMI-devel-18.12.1-1a13f2f
WTMI: system early-init
SVC REV: 5, CPU VDD voltage: 1.237V
NOTICE:  Booting Trusted Firmware
NOTICE:  BL1: v1.5(release):1f8ca7e-dirty (Marvell-devel-18.12.2)
NOTICE:  BL1: Built : 10:16:46, Oct 13 2021
NOTICE:  BL1: Booting BL2
NOTICE:  BL2: v1.5(release):1f8ca7e-dirty (Marvell-devel-18.12.2)
NOTICE:  BL2: Built : 10:16:50, Oct 13 2021
NOTICE:  BL1: Booting BL31
NOTICE:  BL31: v1.5(release):1f8ca7e-dirty (Marvell-devel-18.12.2)
NOTICE:  BL31: Built : 10

U-Boot 2018.03-devel-18.12.3-gc9aa92c-dirty (Oct 13 2021 - 10:14:54 -0300)

Model: Netgate 1100
       CPU     1200 [MHz]
       L2      800 [MHz]
       TClock  200 [MHz]
       DDR     750 [MHz]
DRAM:  1 GiB
Comphy chip #0:
Comphy-0: USB3          5 Gbps
Comphy-1: PEX0          2.5 Gbps
Comphy-2: SATA0         6 Gbps
SATA link 0 timeout.
AHCI 0001.0300 32 slots 1 ports 6 Gbps 0x1 impl SATA mode
flags: ncq led only pmp fbss pio slum part sxs
PCIE-0: Link down
MMC:   sdhci@d0000: 0, sdhci@d8000: 1
Loading Environment from SPI Flash... SF: Detected mx25u3235f with page size 256 Bytes, erase size 64 KiB, total 4 MiB
OK
Model: Netgate 1100
Net:   eth0: neta@30000 [PRIME]
Hit any key to stop autoboot:  0
## Error: "sdboot" not defined
Card did not respond to voltage select!
    12725   armada-3720-netgate-1100.dtb
    12725   armada-3720-sg1100.dtb
    12908   armada-3720-netgate-2100.dtb
    12908   armada-3720-sg2100.dtb

4 file(s), 0 dir(s)

2097152 bytes read in 61 ms (32.8 MiB/s)
12725 bytes read in 9 ms (1.3 MiB/s)
## Starting EFI application at 07000000 ...
Card did not respond to voltage select!
Scanning disk sdhci@d0000.blk...
Disk sdhci@d0000.blk not ready
Scanning disk sdhci@d8000.blk...
Found 4 disks
Consoles: EFI console
    Reading loader env vars from /efi/freebsd/loader.env
Setting currdev to disk0p2:
FreeBSD/arm64 EFI loader, Revision 1.1

   Command line arguments: loader.efi
   Image base: 0x7000000
   EFI version: 2.70
   EFI Firmware: Das U-Boot (rev 0.00)
   Console: efi (0x1000)
   Load Path: /\armada-3720-sg1100.dtb
   Load Device: /VenHw(e61d73b9-a384-4acc-aeab-82e828f3628b)/eMMC(1)/eMMC(0)/HD(2,0x01,0,0x64001,0x1117c)
Trying ESP: /VenHw(e61d73b9-a384-4acc-aeab-82e828f3628b)/eMMC(1)/eMMC(0)/HD(2,0x01,0,0x64001,0x1117c)
Setting currdev to disk0p2:
Trying: /VenHw(e61d73b9-a384-4acc-aeab-82e828f3628b)/eMMC(1)/eMMC(0)/HD(1,0x01,0,0x1,0x64000)
Setting currdev to disk0p1:
Trying: /VenHw(e61d73b9-a384-4acc-aeab-82e828f3628b)/eMMC(1)/eMMC(0)/HD(3,0x01,0,0x7517d,0xe1bd03)
Setting currdev to zfs:pfSense/ROOT/default:
Loading /boot/defaults/loader.conf
Loading /boot/defaults/loader.conf
Loading /boot/device.hints
Loading /boot/loader.conf
Loading /boot/loader.conf.local
|
|          __
    _ __  / _|___  ___ _ __  ___  ___      _
   | '_ \| |_/ __|/ _ \ '_ \/ __|/ _ \   _| |_
   | |_) |  _\__ \  __/ | | \__ \  __/  |_   _|
   | .__/|_| |___/\___|_| |_|___/\___|    |_|
   |_|


 ╔════ Welcome to Netgate pfSense Plus ════╗      __________________________
 ║                                         ║     /                       ___\
 ║  1. Boot Multi user [Enter]             ║    |                      /`
 ║  2. Boot Single user                    ║    |                     /    :-|
 ║  3. Escape to loader prompt             ║    |      _________  ___/    /_ |
 ║  4. Reboot                              ║    |    /` ____   / /__    ___/ |
 ║  5. Cons: Serial                        ║    |   /  /   /  /    /   /     |
 ║                                         ║    |  /  /___/  /    /   /      |
 ║  Options:                               ║    | /   ______/    /   /  _    |
 ║  6. Kernel: default/kernel (1 of 1)     ║    |/   /          /   / _| |_  |
 ║  7. Boot Options                        ║        /          /___/ |_   _| |
 ║                                         ║       /                   |_|   |
 ║                                         ║      /_________________________/
 ╚═════════════════════════════════════════╝                                  |
   Autoboot in 0 seconds. [Space] to pause
Loading kernel...