Permit from VLAN subnet to WAN only
-
I have created a new VLAN interface. Now I would like to (exclusively) allow traffic coming from this subnet to the WAN and not to any other subnets like WLAN or LAN.
Does this require a "reject" rule on each interface? I was expecting a rule like "permit any traffic coming from iface VLAN_IFACE to WAN_IFACE"
-
I have the same issue but I have six VLANs rather than one. I need to allow outbound internet from one of these VLANs for WAN only on ports 80 and 443. (i.e. no access to the other VLANs). The only way I can make it work is to use an any on the Destination which means that I need 12 rules to stop this one VLAN from accessing all the others.
Is there any way of defining a destination as an interface rather than a network address range or is there a way that I can combine multiple Destination nets into one blocking rule.
If needs be I am happy to edit the XML config file directly if necessary rather than use the GUI.
-
Does this require a "reject" rule on each interface? I was expecting a rule like "permit any traffic coming from iface VLAN_IFACE to WAN_IFACE"
A reject rule on each interface doesn't help because traffic is ONLY filtered when it enters the firewall (e.g. the incoming interface).
Since WAN is defined as anything but local LANs you cannot easily define the allowed range. The denied range is way easier, then allow the rest. Rules are always processed from top to bottom. The first rule that fits will be executed and the following ones are ignored.With this in mind do the following:
Goto Firewall|Aliases and create an alias holding all local subnets.Now go to Firewall|Rules and select the VLAN interface in question (or one after another).
Add a rule to permit traffic to this subnet (to be able to get DHCP, DNS etc. from your pfSense. Not sure if this is really needed but doesn't hurt).
Add a rule below this one and block or reject traffic to the alias of all subnets you created earlier.
Add a third rule below this one to allow traffic to the rest (e.g. WAN for internet etc.)You can copy those rules to other interfaces (or VLANs) by hitting the "+" sign next to the rule and change the interface accordingly.
That's it. -
Thanks Chris, that is a great suggestion. I've also setup an Alias for the port set (80 and 443) which has enabled me to reduce these 12 rules down to 2 which makes it manageable in the longer term.
-
I've created an alias for all RFC1918 addresses. Comes in VERY handy in some situations (BYOD and Guest net for example :) )
-
Does this require a "reject" rule on each interface? I was expecting a rule like "permit any traffic coming from iface VLAN_IFACE to WAN_IFACE"
A reject rule on each interface doesn't help because traffic is ONLY filtered when it enters the firewall (e.g. the incoming interface).
Since WAN is defined as anything but local LANs you cannot easily define the allowed range. The denied range is way easier, then allow the rest. Rules are always processed from top to bottom. The first rule that fits will be executed and the following ones are ignored.With this in mind do the following:
Goto Firewall|Aliases and create an alias holding all local subnets.Now go to Firewall|Rules and select the VLAN interface in question (or one after another).
Add a rule to permit traffic to this subnet (to be able to get DHCP, DNS etc. from your pfSense. Not sure if this is really needed but doesn't hurt).
Add a rule below this one and block or reject traffic to the alias of all subnets you created earlier.
Add a third rule below this one to allow traffic to the rest (e.g. WAN for internet etc.)You can copy those rules to other interfaces (or VLANs) by hitting the "+" sign next to the rule and change the interface accordingly.
That's it.Hello,
Is this still the way it goes?
Or is it possible to add only one permit rule with source net vlan to destination net wan?Regards
-
Sorry to drudge this up again. Jahonix's solution worked great for me, but like stickybit i'm curious if this is still the best way to accomplish this?
-
permit rule with source net vlan to destination net wan?
There is no destination net "WAN" describing the "rest of the internet".
It would point to your WAN interface's public IP to which you surely do not want to connect to. -
if this is still the best way to accomplish this?
Yes as far as the rule set is concerned.
No for multiple interfaces. Use "Floating rules" for this now. https://doc.pfsense.org/index.php/What_are_Floating_Rules -
Don't forget to block connections to This Firewall too. Else they can get at your webgui on the WAN address (if it's not RFC1918)