PC Engines apu2 experiences

Stewart

I'm running a full install.

kevindd992002

Without any modifications like using ramdisks for /tmp and /var? Fulll install as is?

Stewart

Yes. Using an msata ssd.

mikeboss

@Stewart:

Second, the APU2C4 only has about 73% of the performance of the APU1D using a single core and no hardware acceleration.

I saw similar results, back when I got my first APPU2. it seemed to be odd but then I re-ran the benchmark a few times and I always got more or less the same score each time…

APU1 https://browser.primatelabs.com/geekbench3/4636493
APU2 https://browser.primatelabs.com/geekbench3/4635680

regards,
michael

kevindd992002

Are the APU2 developers already aware of this? This issue seems to be a major one that needs addressing, right?

Qinn

I read there is a module for using the 3 front LEDs on the apu2 boards (http://pcengines.ch/howto.htm#gpio), has anyone using pfSense experience with this?

Thanks in advance,

Cheers Qinn

maglub

Hi,

I just set up two APU2C4 boxes with pfSense 2.3.2. After a bit of fiddling with the USB stick for TinyCore, I managed to get it installed. On a 1Gbit connection, I had >800Mbit down and up through the firewall. No tuning what so ever.

I am using pfSense-CE-2.3.2-RELEASE-4g-amd64-nanobsd.img.gz

j4k3

Hey Guys, I wish I was getting maglub's performance out of the box.

I just received a APU2C4 in the mail and loaded pfSense-CE-memstick-serial-2.3.2-RELEASE-amd64 on it.

It manages to boot fine, and it's fully functional, the web interface moves much quicker and more fluid than the old ALIX2D3 it had replaced.

However when I run iperf on the LAN interface from another host, I'm only getting 300Mbps or so.

I found this thread about Intel I210AT nics and am attempting their suggestions:

https://redmine.pfsense.org/issues/1221

I see they're playing with the buffers and queues.

My question is this, if I edit loader.conf.local after looking at some of the options some options have "Quotes" around them, and others don't.

If I directly edit loader.conf.local when I specify variables in there, must they use " for the value? Or will just the value suffice?

hw.igb.num_queues="4" or hw.igb.num_queues=4 ?

Thanks

cwagz

I always use the quotes. I have not tried it without.

j4k3

Thanks for the insight, I managed to finally get close to 1Gbps on the lan interface.

I had to uncheck Disable hardware large receive offload, and Disable hardware TCP segmentation offload

Under System > Advanced > Networking

Based on what I've read so far I know this unit won't route more than 500 Mbps or so but I wanted to at least understand why, the nic was so hobbled right off the bat.

cwagz

I am looking for some opinions on downsizing my current pfSense system with an APU2C4.

Currently I have:
Supermicro A1SRI-2558
8GB Ram
120GB SSD
Akasa Fanless Enclosure

There are 6 people in my house and 30 or so devices. I am the only person that ever uses OpenVPN and it is usually from a mobile device on LTE so OpenVPN performance is probably not a huge deal. I run Squid and Squidguard to proxy the internet for my kids. Our internet connection is FiOS 150/150 Mbps.

It seems like I could build an apu2c4 and sell my current hardware. I would probably have money left over and a smaller, slightly cooler running device for pfSense.

Do you guys see any potential performance issues or reasons why this is a bad idea?

Stugots

Does anyone know of a way to enable TRIM support on the SSD without having to boot of a recovery device? Is there some sort of tunable where it can be enabled on the next reboot?

AndrewZ

@acascianelli:

Does anyone know of a way to enable TRIM support on the SSD without having to boot of a recovery device?

https://forum.pfsense.org/index.php?topic=66622.0
https://forum.pfsense.org/index.php?topic=113803.msg633795#msg633795

lachendichatz

I switched from A1SRI-2758/8GB to apu2c4 as I need the 2758 for another server.

Running iperf3 between two pcs connected by the apu (pfsense 2.3.2) I get
600Mbit/s in one direction
615Mbit/s in the other one.
CPU runs at 25% load, e.g. one core is maxed out.

I probably see different speeds because I already imported my old firewall rules and have three rules on one nic and around 20 on the other one.

I observed the same speed & load when I installed debian and configured a few iptable rules.

Adding more clients (iperf -P 8 ) gives me:
940Mbit/s direction a
690Mbit/s direction b
880MBit/s duplex

Enabling (disabling unchecked) segmentation offload gives me
940Mbit/s direction a
695Mbit/s direction b
940Mbit/s duplex
CPU runs at 85%

Speedtest (init7) shows me 930down/940up. Initially I got 720/920 & 670/920 but that was because of my slow laptop (sigh). Restarting firefox gave me consistent speeds around 940.

So I can route a single TCP connection at 600Mbit/s per core. One could probably achieve higher speeds by tuning ISR related configs but as I can saturate my gigabit line with multiple connections I won't change settings.

I set igb_numqueue to 4 and mbuf to 1mio. Unknown if it had an effect.
Somebody suggested to set a rx/tx level (or queue? dont remeber) to 8k. That did not have an effect.
powerD disabled/enabled (hiadaptive) did not make a difference

Stugots

@AndrewZ:

@acascianelli:

Does anyone know of a way to enable TRIM support on the SSD without having to boot of a recovery device?

https://forum.pfsense.org/index.php?topic=66622.0
https://forum.pfsense.org/index.php?topic=113803.msg633795#msg633795

Is there no way to set it so that it's enabled on the next reboot without going into single user mode?

Guest

Is there no way to set it so that it's enabled on the next reboot without going into single user mode?

Actually is there no way or workaround, as I am informed right.

kevindd992002

@j4k3:

Thanks for the insight, I managed to finally get close to 1Gbps on the lan interface.

I had to uncheck Disable hardware large receive offload, and Disable hardware TCP segmentation offload

Under System > Advanced > Networking

Based on what I've read so far I know this unit won't route more than 500 Mbps or so but I wanted to at least understand why, the nic was so hobbled right off the bat.

Does that mean these two should be unchecked to get the full potential of the NIC's of the APU2C4? Any disadvantages of keeping them unchecked (enabled)?

hda

@kevindd992002:

… Any disadvantages of keeping them unchecked (enabled)?

Possibly, like no or a snappy WAN-PPPoE connection.

hda

@acascianelli:

…Is there no way to set it so that it's enabled on the next reboot without going into single user mode?

https://forum.pfsense.org/index.php?topic=121515.msg673176#msg673176 / pfSense 2.4

kevindd992002

@hda:

@kevindd992002:

… Any disadvantages of keeping them unchecked (enabled)?

Possibly, like no or a snappy WAN-PPPoE connection.

But why is the NIC performance hampered with these settings disabled anyway?

@hda:

@acascianelli:

…Is there no way to set it so that it's enabled on the next reboot without going into single user mode?

https://forum.pfsense.org/index.php?topic=121515.msg673176#msg673176 / pfSense 2.4

So if I understand this correctly, a fresh install of 2.4 will already enabled TRIM automatically with no user intervention? And same goes with older versions of pfsense that upgrade 2.4, TRIM will be enabled?