PfSense on esxi 6.7, can get it to work propperly.
-
Is that your setup in esxi like this?
physical port LAN - > virtual switch LAN -> Port group LAN -> VLAN ID empty
physical port WAN -> virtual switch WAN -> Port group WAN -> T-mobile fiberHow are your other virtual machines connected?
And how do they get IPs?
And do they have internet access via pfsense -> WAN -> t-mobile? -
@three said in PfSense on esxi 6.7, can get it to work propperly.:
Is that your setup in esxi like this?
physical port LAN - > virtual switch LAN -> Port group LAN -> VLAN ID empty
physical port WAN -> virtual switch WAN -> Port group WAN -> T-mobile fiberYes
physical port LAN - > virtual switch LAN -> Port group LAN -> VLAN ID empty
physical port WAN -> virtual switch WAN -> Port group WAN -> T-mobile fiber ( or on the LAN of the USG )How are your other virtual machines connected?
network adapters on the LAN group
And how do they get IPs?
trough DHCP.
And do they have internet access via pfsense -> WAN -> t-mobile?
Correct.
-
So, all VMs are in LAN and do get IP addresses from pfsense and they are able to connect to internet. That's good but all virtual within ESXI.
Now, when you plug in a cable between your ESXI LAN port on your physical network switch, those devices do not get IP addresses.
Is this switch managed? Any VLAN settings on the particular physical switch port? Have you tried another physical switch port? Have you tried to directly connect a device via cable to your ESXI LAN port?
-
@three said in PfSense on esxi 6.7, can get it to work propperly.:
So, all VMs are in LAN and do get IP addresses from pfsense and they are able to connect to internet. That's good but all virtual within ESXI.
Now, when you plug in a cable between your ESXI LAN port on your physical network switch, those devices do not get IP addresses.
Is this switch managed? Any VLAN settings on the particular physical switch port? Have you tried another physical switch port? Have you tried to directly connect a device via cable to your ESXI LAN port?
That is correct, all the VM's are getting internet access. But when i put a network cable form the NIC port to a switch, or direct into a client. there is no internet access. The devices are getting a IP adress like: 169.254.10.189.
Same behavior when the cable is plugged into a normal switch.
-
something must be fucked up, vlan id 4095 means that you set the vswitch as trunk port like you would do in a real switch to let all vlan pass.
169.254 no dhcp lease is offered
if you can pls post some screenshot of your esxi configuration
i'm using VMXNET3 and don't forget to install open-vm-tools
be sure it's the correct physical NIC port -
I agree, something seems wrong with ESXI setup. Some screenshots could indeed help.
Just to be on the safe side: Your test with Windows Server 2019 and Virtualbox involved the very same machine? On which you are now operating with ESXI? And you are using the very same physical ethernet port for LAN on this machine?
-
Yes this is the same machine with esxi 6.7 or with Windows server 2019.
First off all let me explain this first.Since this CPU cant run vt-d i need to disable this at the start with: noiommu in the /bootbank/boot.cfg at the end of the line with kernelopt: http://www.digitalroadies.com/vmware-6-initializing-iov-issues/
By default the realtek nic card is not working within ESXI so i need to install a driver for it:
https://networkguy.de/installing-realtek-driver-on-esxi-6-7/After that i followed the tutorial: https://docs.netgate.com/pfsense/en/latest/virtualization/virtualizing-pfsense-with-vmware-vsphere-esxi.html for creating the WAN and LAN ports.
i have made a couple of screenshots for you off the settings that i have made on the WAN - LAN and uploaded it here:
https://imgur.com/a/IgPD7DUDont mind the link down at the nics, that is correct becuase i have remove the cables.
When i insert the cables the nics are up.I will make some more screenshot of the settings inside PfSense, and the Ubuntu vm.
-
Sorry,
The WAN is a wrong setting. this is the right setting for the WAN.
It's the WAN of the vmnetwork of the onboard NIC of the motherboard, -
and here are some screenshots.
you can see that the ubuntu instalation on ESXI is working perfectly with internet access.
it running on the DHCP lease of 10.0.0.X.You can also see that my Windows 10 laptop and my Synology NAS wich are connected trough LAN cable on the NIC are not getting the right IP address. so there is no DHCP.
https://imgur.com/a/ZDUSXnm
-
Are both, network adapter 1 and 2, realteks?
EDIT 1:
Just saw that wan and lan are Realtek, but VMNetwork is Intel.Need to look again ...
EDIT 2:
At the time it works, does your WAN (Network Adapter 1) is set to VM Network or WAN?
-
It only works when i set the WAN on VM Network.
When i set it on WAN it wont work. -
Then it is related to the realteks. You somehow need to validate whether they operate properly in ESXI at all. Another option could be, as mentioned by @kiokoman, to change to vmxnet3 in pfsense-VM-settings of ESXI.
-
yeah in any case realtek card are never a good choice for this stuff
-
ok.
In the meantime i have tried to run PfSense directly installed on a SSD.
That is running fine, and working woth both the INTEL nic for the WAN and the realtek as the LAN.The devices that are attached trough a LAN kabel are getting 10.0.0.X and internet access,
When i tried it with windows 2019 its working perfect without a problem. So i think i need to consider to leave ESXI for what it is. or try a different hyperviser OS.i only want to use it for:
1x windows server machine
1x firewall machine
2-3 linux machines.Any thought?
-
change that realtek card to some intel they are cheap on ebay / amazon after all
-
Exactly what I would recommend as well. It would cost only a few bucks and will work right out of the box with ESXI. Otherwise you need to spend countless hours or days to get into another hypervisor. Do the math to your liking :)
-
Thank you both for the help :) i will buy a Intel card ;)
I just found one of these: https://ark.intel.com/content/www/us/en/ark/products/184824/intel-ethernet-network-adapter-i350-t4-for-ocp-3-0.html for €20 euro.
Will this one work?
-
With ESXi have you tried putting the LAN vSwitch and Port Group into promiscuous mode ?
-
ok so, i bought this https://ark.intel.com/content/www/us/en/ark/products/184824/intel-ethernet-network-adapter-i350-t4-for-ocp-3-0.html inserted it in the ESXI and booted up. It works perfectly.
So now it is running and working like this:
Fiber optic > Ubiquiti USG router WAN > Ubiquiti USG router LAN > network port NIC ESXI WAN > network port NIC ESXI LAN > Network switch and accespoint in the house. ( 10.0.0.X range. ) this is working perfect.
But i want to remove the Ubiquiti usg router so i can setup the fiber optic directly into the WAN port of the NIC of the ESXI.
so i'm working with T-Mobile here in here in the Netherlands. and i have added the VLAN 300 for internet into the PfSense on the interface of the WAN port of the NIC:
Under interfaces > assigment i have put the new VLAN300 into the WAN:
But i dont get a IP from the DHCP server of my ISP provider.When i set it back on the normal settings, everything is working perfect and i get a 192.168.1.2 from the Ubiquiti USG.
-
under esxi did you set the vswitch to vlanid 4095 ?
-
So i need to edit this one:
This is the nic port that is comming from the fiber optic.And can you tell me WHY i need to add VLAN 4095?
-
This is a specific of ESXI. If empty, VLAN are NOT supported. 4095 allows ALL VLAN numbers from the VM. I still get confused about VLAN, tagged, untagged, etc. But this should work,
-
indeed 4095 means that you set your vswitch as a trunk port letting any vlan pass through
-
Yes, this did the trick :)
-
so after a few day's working perfectly.
it now randomly stops working.In the PfSense VM i see this:
When i reboot the VM everything works again.
What can this be? -
try to reinstall open-vm-tools
maybe do a fsck also -
i have reinstalled the open-vm-tools and nothing changed
what you mean by fsck?And what about the new update?
i'm now on:2.4.4-RELEASE-p3 (amd64)
built on Wed May 15 18:53:44 EDT 2019
FreeBSD 11.2-RELEASE-p10 -
fsck: from console is option 5 and F key ( F: Reboot and run a filesystem check )
and yes, upgrade to 2.4.5 -
ok now i understand what you mean. i just did that a couple of hours ago and it seems to work again.
What about the update?after the update i need to reinstall vm-tools again? and another fsck?
-
nope, no need, make a backup of your config just in case and do the upgrade
-
Still this is not working fine. My internet disconnects every 4-5 hour.
So can you please check my settings and tell me if the are right:First off all, the network settings:
-
ESXI WAN settings: + VLAN ID 4095
-
ESXI LAN settings:
-
PfSense settings:
Cable managment:
WAN T-mobile > WAN Port intel NIC ESXI
LAN Port intel NIC > port 1 into standard network switch. ( not managed )
port 2 network switch > Onboard LAN port of ESXI server for managment.
The rest of the network ports of the switch are 2 Ubiquiti WIFI accespoint, and some computers.As you can see, i also installed OpnSense just to find our of PfSense was the problem.
But also OpnSense has the same problems. -
-
it's ok, was the cable removed during this screenshot i suppose? physical adapters are not green
if you are using igbn (native esxi driver) try to install net-igb (intel driver for esxi)also install open-vm-tools from pfsense packages if you didn't already
-
Yes, the cable is removed otherwise i dont have good internet ofcourse :)
Both the drivers are installed:
Also the package in PfSense for open-vm-tools is installed.
-
idk, settings are ok, maybe do a backup of your configuration ad reinstall a new clean vm with pfsense 2.4.5 or try 2.5.0
-
Can I get a Teamviewer into the box... then I will have your ESXi/pfsense running in 5 mins
-
@kiokoman
I have tried freshinstall of 2.4.5 and 2.5.0
I have tried backing up and restoring.Maybe te problem is the fact i dont enter a MAC-ADDRESS into the wan port of the T-mobile fiber?
and i leave the MTU also clear?@Cool_Corona
if you can do it in 5 minutes. you can also tell me how ;) -
that would be something specific to your isp
-
So i tried adding a MAC-ADDRESS but then there is no internet at all.
Where in PfSense can i find a log? so maybe i can see where the problem is occurring. -
all logs are under status / system log
what kind of connection is it? pppoe ? dhcp? static or dynamic ip? -
I have a cable modem and for testing purposes I have been switching between a pfSense VM and physical appliances.
Not sure why - but my connection is stable with the mac address used when the connection was first setup. This may be a provider thing...
Either way - if you want your pfSense VM to use a custom mac address on the WAN interface you'll need to allow forged transmits.
I'd also suggest you enable promiscuous mode.
https://docs.vmware.com/en/VMware-vSphere/6.7/com.vmware.vsphere.security.doc/GUID-7DC6486F-5400-44DF-8A62-6273798A2F80.html
and
https://docs.vmware.com/en/VMware-vSphere/6.7/com.vmware.vsphere.security.doc/GUID-92F3AB1F-B4C5-4F25-A010-8820D7250350.html
and
https://wahlnetwork.com/2013/04/29/how-the-vmware-forged-transmits-security-policy-works/
For good measure also allow mac changes.
Once its all working... you can revert these settings until you know exactly which setting breaks your environment.
To sum this up: on the WAN vSwitch and Portgroup you need to:
-
Allow Mac Changes
-
Allow Forged Transmits
-
Allow Promiscuous Mode
-
In pfsense - on the WAN Interface use a Mac Address that has previously worked with your provider
-