Vlan and cisco slm2008
-
I have problem with vlan. I've read documentation and forum posts and tried lot of option but it still doesn't work.
Here is my cisco vlan settings
pfsense is connected to port 1 on switch
raspberry is connected to port 6 on switchhere is my pfsesnse vlan settings
VLAN 100 interface has ip 192.168.20.2
Now I try to ping from Diagnostic->Ping
192.168.20.1 (raspberry)
but raspberry is not responding.what am i doing wrong?
p.s How can I check that my LAN card is VLAN capable ? -
Are you sure the Raspberry responds to ping requests?
Can you connect a device to port g6 the is known to respond to g6 and give that a try?
Are you sending the diagnostics ping on the correct interface (LAN)?
For end point devices you may want to use Access mode.
I put the WAN on VLAN and leave LAN to use the default untagged vlan 1. There is fewer ports/connections involved with the WAN that need VLAN configuration. And no configuration needed for LAN devices.
-
Hi NOYB
Thanks for your reply. This is my testing enviroment because I cant make it works on production pfsense.
My end scenario is connect 3 ADSL modem to one single NIC on pfsense with help of SLM2008.In my testing enviroment Raspberry works as a ADSL modem and yes Raspberry respond to ping.
When I am pinging from pfsense I set correct interface.
Today I will add another NIC to my pfsense and connect Raspberry to WAN port thru cisco and my laptop to LAN port. This will be exactly like on production architecture and show you my settings. -
Hi
Ok I am lost. Have no idea what is wrong.
Now I have two NIC one for WAN (VLANs) and one for LAN.LAN ip is 192.168.2.1
WAN ip is 192.168.3.2
WAN2 vlan 100 ip is 192.168.30.2cisco settings
pfsense is connected to port g1
Raspberry is connected to port g6Can't ping Raspberry from diagnostic->ping interfaces WAN2
I've also tried to change NIC but still no luck.
Any idea? -
Packet capture / sniffer.
Firewall -
I am not familiar with the details of Cisco switch settings but I suspect port g6 shouldn't be a trunk port.
It would be helpful to know:
1. Is the ping going out the correct interface?
2. Is the ping getting to raspberry?
3. Is raspberry generating a response?
4. Is the response getting to the correct interface?Packet capture can help answer these questions. pfSense has the a GUI interface for packet capture: Diagnostics -> Packet Capture and a command line utility: tcpdump.
What OS does raspberry run?
Did you restart pfSense after you changed the interfaces? (I have found that sometimes a restart is necessary to clear out "old" configuration information.)
-
Interface VLAN Mode—Select an option to configure the port type with respect to VLAN membership and tagging.
General—The port can be a member of one or more tagged or untagged VLANs. This mode allows the full capabilities specified in the IEEE 802.1Q specification, “VLAN Tagging.”
Access—The port can accept only untagged frames. An access port can be a member of only one VLAN and it uses the VLAN ID as its port VLAN ID (PVID). Access ports are typically used to connect hosts, which become members of the VLAN by virtue of being physically connected to the port.
Trunk—The port can be assigned to only one untagged VLAN, the native VLAN, and can be assigned to any number of tagged VLANs (or none). Trunk ports carry traffic for multiple VLANs from the switch to other network devices, such as an upstream router or an edge switch.
Although Access for the Blackberry connection port and General mode for the pfSense WAN connection port would probably be more appropriate. Don't think Trunk mode should cause a problem in this case. Think Trunk mode is default used by this switch. Even for the default untagged management vlan 1.
It is time for some network captures to identify how far the ping requests/replys are getting (where they are being blocked).
-
Hi.
wallabybob and NOYB thanks for your reply and some hints.
I am step further.
I started ping from raspberry to pfsesne then I upgraded firmware on cisco and finally see some output of tcpdump.
My cisco setting now are as follow:Before upgrade command "tcpdump -i re1_vlan100 -n -e -vv" shows nothing, right know:
tcpdump: listening on re1_vlan100, link-type EN10MB (Ethernet), capture size 96 bytes 12:38:42.186047 b8:27:eb:c4:36:b6 > 64:70:02:11:ab:5e, ethertype IPv4 (0x0800), length 98: (tos 0x0, ttl 64, id 0, offset 0, flags [DF], proto ICMP (1), length 84) 192.168.30.1 > 192.168.30.2: ICMP echo request, id 3954, seq 1193, length 64
also
tcpdump -i re1 -n -e -vv shows tagged packet
tcpdump: listening on re1, link-type EN10MB (Ethernet), capture size 96 bytes
12:31:01.203161 b8:27:eb:c4:36:b6 > 64:70:02:11:ab:5e, ethertype 802.1Q (0x8100), length 102: vlan 100, p 0, ethertype IPv4, (tos 0x0, ttl 64, id 0, offset 0, flags [DF], proto ICMP (1), length 84)
192.168.30.1 > 192.168.30.2: ICMP echo request, id 3954, seq 732, length 64
12:31:02.062324 20:bb:c0:78:83:32 > 01:80:c2:00:00:00, 802.3, length 60: LLC, dsap STP (0x42) Individual, ssap STP (0x42) Command, ctrl 0x03: STP 802.1w, Rapid STP, Flags [Proposal, Learn, Forward, Agreement], bridge-id 8000.20:bb:c0:78:83:31.8001, length 43
message-age 0.00s, max-age 20.00s, hello-time 2.00s, forwarding-delay 15.00s
root-id 8000.20:bb:c0:78:83:31, root-pathcost 0, port-role Designated
12:31:02.203080 b8:27:eb:c4:36:b6 > 64:70:02:11:ab:5e, ethertype 802.1Q (0x8100), length 102: vlan 100, p 0, ethertype IPv4, (tos 0x0, ttl 64, id 0, offset 0, flags [DF], proto ICMP (1), length 84)
192.168.30.1 > 192.168.30.2: ICMP echo request, id 3954, seq 733, length 64
12:31:03.203146 b8:27:eb:c4:36:b6 > 64:70:02:11:ab:5e, ethertype 802.1Q (0x8100), length 102: vlan 100, p 0, ethertype IPv4, (tos 0x0, ttl 64, id 0, offset 0, flags [DF], proto ICMP (1), length 84)
192.168.30.1 > 192.168.30.2: ICMP echo request, id 3954, seq 734, length 64
12:31:04.063285 20:bb:c0:78:83:32 > 01:80:c2:00:00:00, 802.3, length 60: LLC, dsap STP (0x42) Individual, ssap STP (0x42) Command, ctrl 0x03: STP 802.1w, Rapid STP, Flags [Proposal, Learn, Forward, Agreement], bridge-id 8000.20:bb:c0:78:83:31.8001, length 43
message-age 0.00s, max-age 20.00s, hello-time 2.00s, forwarding-delay 15.00s
root-id 8000.20:bb:c0:78:83:31, root-pathcost 0, port-role Designated
12:31:04.202970 b8:27:eb:c4:36:b6 > 64:70:02:11:ab:5e, ethertype 802.1Q (0x8100), length 102: vlan 100, p 0, ethertype IPv4, (tos 0x0, ttl 64, id 0, offset 0, flags [DF], proto ICMP (1), length 84)
192.168.30.1 > 192.168.30.2: ICMP echo request, id 3954, seq 735, length 64I still CANT ping raspberry from WAN2 and still CANT ping WAN2 from raspberry.
p.s
- I can ping raspberry if I connect my mac to raspberry.
- raspberry has latest Raspbian “wheezy”
- I added rule to WAN2 to pass everything
-
I still CANT ping raspberry from WAN2
Does a tcpdump verify the ping goes out the correct interface with the correct VLAN tag? (I didn't see an answer to my question )Did you restart after changing the pfsense interfaces around?
Does a tcpdump on raspberry show the incoming ping request?and still CANT ping WAN2 from raspberry.
This might be easy to fix. You have added a firewall rule to allow that but did you reset firewall states after adding the rule? (See Diagnostics -> States, click on Reset States tab, read, remember and click the Reset button.)
-
Does a tcpdump verify the ping goes out the correct interface with the correct VLAN tag?
re1_vlan100: flags=8843 <up,broadcast,running,simplex,multicast>metric 0 mtu 1500
options=3 <rxcsum,txcsum>ether 64:70:02:11:ab:5e
inet6 fe80::6670:2ff:fe11:a984%re1_vlan100 prefixlen 64 scopeid 0x9
inet 192.168.30.2 netmask 0xffffffff broadcast 192.168.30.2
nd6 options=43 <performnud,accept_rtadv>media: Ethernet autoselect (1000baseT <full-duplex>)
status: active
vlan: 100 parent interface: re1When I ping from pfsense to raspberry
tcpdump show nothing on re1_vlan100 interface
[2.0.3-RELEASE][admin@pfSense.localdomain]/root(4): tcpdump -i re1_vlan100 -n -e -vv tcpdump: listening on re1_vlan100, link-type EN10MB (Ethernet), capture size 96 bytes
I've also checked re1 and fxp0 if there is any echo but found nothing.
Did you restart after changing the pfsense interfaces around?
yes many many times
Does a tcpdump on raspberry show the incoming ping request?
No, nothing. ( I've also conneted raspberry to mac to verify that tcpdump shows echo and found it. )
This might be easy to fix. You have added a firewall rule to allow that but did you reset firewall states after adding the rule? (See Diagnostics -> States, click on Reset States tab, read, remember and click the Reset button
Did not help.
If i ping WAN2 from raspberry tcpdump on pfsense show tagged packet and echo request but WAN2 is not responding at all.
Here is my rule on WAN2
</full-duplex></performnud,accept_rtadv></rxcsum,txcsum></up,broadcast,running,simplex,multicast> -
re1_vlan100: flags=8843 <up,broadcast,running,simplex,multicast>metric 0 mtu 1500
options=3 <rxcsum,txcsum>ether 64:70:02:11:ab:5e
inet6 fe80::6670:2ff:fe11:a984%re1_vlan100 prefixlen 64 scopeid 0x9
inet 192.168.30.2 netmask 0xffffffff broadcast 192.168.30.2
nd6 options=43 <performnud,accept_rtadv>media: Ethernet autoselect (1000baseT <full-duplex>)
status: active
vlan: 100 parent interface: re1</full-duplex></performnud,accept_rtadv></rxcsum,txcsum></up,broadcast,running,simplex,multicast>Why is the netmask 0xffffffff? 192.168.30.1 is NOT on the same subnet as re1_vlan100! I suggest you use a more conventional netmask such as 0xffffff00 so the subnet has enough IP addresses to be "interesting".
-
You are right.
After 5 days of fighting with this I made this small typo :)
Now it is working like a charm.
So for people having same issue with cisco SLM20XX you should upgrade firmware to 1.0.6.2 for VLAN working (and set correct netmask ;))wallabybob and NOYB I really appreciate your help. Thank you.