-
Hi!
I did a fresh install of 2.3 and restored config from previous 2.3 that was running on the same box.
Now the funny part.
Traffic between 2 em nics is limited to 100Mbit iperf below:
C:\iperf>iperf3 -c 172.16.16.245 -t 600 Connecting to host 172.16.16.245, port 5201 [ 4] local 10.10.0.60 port 53618 connected to 172.16.16.245 port 5201 [ ID] Interval Transfer Bandwidth [ 4] 0.00-1.00 sec 11.5 MBytes 96.2 Mbits/sec [ 4] 1.00-2.01 sec 11.4 MBytes 94.4 Mbits/sec [ 4] 2.01-3.00 sec 11.1 MBytes 94.3 Mbits/sec [ 4] 3.00-4.00 sec 11.4 MBytes 95.3 Mbits/sec [ 4] 4.00-5.00 sec 11.2 MBytes 94.6 Mbits/sec [ 4] 5.00-6.01 sec 11.4 MBytes 94.6 Mbits/sec [ 4] 6.01-7.00 sec 11.1 MBytes 94.2 Mbits/sec [ 4] 7.00-8.00 sec 11.2 MBytes 94.2 Mbits/sec [ 4] 8.00-9.00 sec 11.4 MBytes 95.3 Mbits/sec [ 4] 9.00-10.00 sec 11.2 MBytes 94.5 Mbits/sec [ 4] 10.00-11.01 sec 11.4 MBytes 94.6 Mbits/sec [ 4] 11.01-12.01 sec 11.1 MBytes 93.7 Mbits/sec [ 4] 12.01-13.01 sec 11.4 MBytes 95.5 Mbits/sec [ 4] 13.01-14.00 sec 11.1 MBytes 93.6 Mbits/sec [ 4] 14.00-15.00 sec 11.4 MBytes 95.6 Mbits/sec [ 4] 15.00-16.01 sec 11.4 MBytes 94.6 Mbits/sec [ 4] 16.01-17.01 sec 11.2 MBytes 94.6 Mbits/sec [ 4] 17.01-18.00 sec 11.0 MBytes 92.8 Mbits/sec [ 4] 18.00-19.00 sec 11.5 MBytes 96.3 Mbits/sec [ 4] 19.00-20.00 sec 11.2 MBytes 94.6 Mbits/sec [ 4] 20.00-21.01 sec 11.4 MBytes 94.6 Mbits/sec [ 4] 21.01-22.00 sec 11.1 MBytes 94.1 Mbits/sec [ 4] 22.00-23.00 sec 11.2 MBytes 94.1 Mbits/sec [ 4] 23.00-24.00 sec 11.4 MBytes 95.5 Mbits/sec [ 4] 24.00-25.01 sec 11.4 MBytes 94.6 Mbits/sec [ 4] 25.01-26.00 sec 11.1 MBytes 94.2 Mbits/sec [ 4] 26.00-27.01 sec 11.4 MBytes 95.1 Mbits/sec [ 4] 27.01-28.01 sec 11.2 MBytes 94.2 Mbits/sec [ 4] 28.01-29.00 sec 11.2 MBytes 95.0 Mbits/sec [ 4] 29.00-30.01 sec 11.4 MBytes 94.6 Mbits/sec [ 4] 30.01-31.00 sec 11.1 MBytes 94.1 Mbits/sec [ 4] 31.00-32.01 sec 11.4 MBytes 95.1 Mbits/sec [ 4] 32.01-33.01 sec 11.2 MBytes 94.3 Mbits/sec [ 4] 33.01-34.00 sec 11.2 MBytes 94.6 Mbits/sec [ 4] 34.00-35.00 sec 11.1 MBytes 93.5 Mbits/sec [ 4] 35.00-36.00 sec 11.4 MBytes 95.1 Mbits/sec [ 4] 36.00-36.43 sec 4.75 MBytes 93.4 Mbits/sec - - - - - - - - - - - - - - - - - - - - - - - - - [ ID] Interval Transfer Bandwidth [ 4] 0.00-36.43 sec 411 MBytes 94.6 Mbits/sec sender [ 4] 0.00-36.43 sec 0.00 Bytes 0.00 bits/sec receiver
But this box is capable of 500 Mbits/sec and it already worked just fine when I first upgraded from 2.2.6 to 2.3
After clean install I have above situation.
I
m confused :) Can anyone suggest something? I tried with offloading settings and it doesn
t matter what I tick or untick, always the same 100 mbit speed :S -
Perhaps you had some change to /boot/loader.conf or /boot/loader.conf.local that wouldn't have been backed up?
-
Oh crap.
I have no idea what was there :S -
Probably something from https://doc.pfsense.org/index.php/Tuning_and_Troubleshooting_Network_Cards#Intel_igb.284.29_and_em.284.29_Cards (or an older revision of the page), or who knows… could have been tweaks to the card queues, rx/tx queues/buffers, etc.
-
It`s weird that limit is almost exactly 100Mbits :)
Everywhere it shows as gig ethernet… -
OMG I
m such a dumbass. Why the hell I
m working this on friday night geez.OK, I tested on a virtual machine on server which has flaky DLINK NIC.
Sure, virtual machine was showing me 10Gig (default for Hyper-v guest) and after I checked actual NIC it was 100Mbit/s.
Tomorrow morning this NIC leaves for good.
Now speeds are OK again.
Sorry for the trouble.