<![CDATA[(Solved) Multiwan (failover) DNS not working]]>I need some help with a multi-wan configuration. It is DSL primary and 4G as failover. I'm having trouble with the 4G modem staying up, but something has happened and now I can't get DNS resolution at all.

I can ping 8.8.8.8 both from the pfsense VM command line as well as a client vm connected to the LAN side interface. But no DNS resolution works at the PFsense itself or from the client. I can point the client DIRECTLY to opendns servers and it works and can browse the internet, but if I point it at the pfsense forwarder it fails. The forwarding service is running.

I have DNS servers entered for both WAN gateways.

Any ideas or help?

]]>https://forum.netgate.com/topic/95654/solved-multiwan-failover-dns-not-workingRSS for NodeSat, 18 Apr 2026 16:10:56 GMTWed, 17 Feb 2016 15:49:25 GMT60<![CDATA[Reply to (Solved) Multiwan (failover) DNS not working on Wed, 03 Aug 2016 18:49:06 GMT]]>I ran into the same issue but no matter if I had different Dns addresses I still could not connect on secondary wan of failover.  Disabling Dns resolver and enabling Dns forwarder solved the problem for me.

]]>https://forum.netgate.com/post/641732https://forum.netgate.com/post/641732Wed, 03 Aug 2016 18:49:06 GMT<![CDATA[Reply to (Solved) Multiwan (failover) DNS not working on Sat, 20 Feb 2016 09:53:48 GMT]]>Yeah that's not a valid config. I added input validation so that can't be configured.
https://redmine.pfsense.org/issues/5915

]]>https://forum.netgate.com/post/604171https://forum.netgate.com/post/604171Sat, 20 Feb 2016 09:53:48 GMT<![CDATA[Reply to (Solved) Multiwan (failover) DNS not working on Fri, 19 Feb 2016 19:18:17 GMT]]>Solved… Hopefully this helps someone else using MultiWAN in the future.

When I set up my DNS, I followed the instructions about setting up DNS for each gateway. I use OpenDNS and when I set this up, I set it as follows and it didn't work:

208.67.222.222 on WANA
208.67.220.220 on WANA
208.67.222.222 on WANB
208.67.222.222 on WANB

Long story short, you can't use the same DNS servers on each WAN. Behind the scenes, the system sets a static route for each DNS server using its assigned gateway.

The reason that I was seeing what I was seeing was due to the first two DNS routes being set, then immediately overwritten by the last 2. So when I was in a state where both gateways were started and operational my DNS was attempting to be routed over the disabled gateway. If I brought down the secondary interface the routing for the DNS on that gateway was removed and the primary routes worked.

]]>https://forum.netgate.com/post/604088https://forum.netgate.com/post/604088Fri, 19 Feb 2016 19:18:17 GMT<![CDATA[Reply to (Solved) Multiwan (failover) DNS not working on Wed, 17 Feb 2016 16:02:34 GMT]]>Well I found out some additional information. It is related to the multi wan, but it just stopped working. I didnt make any changes.

If I disable the WANB interface, I get DNS resolution. When I turn WANB back on again, I can resolve for a couple seconds then it starts failing again… don't think it is caching because I try to resolve new sites and it works for 10-30 seconds with newly resolved sites before starting to fail again. Then when it starts failing I get 4 fails in a row (2 servers configured, each with 2 different gateways).

]]>https://forum.netgate.com/post/603481https://forum.netgate.com/post/603481Wed, 17 Feb 2016 16:02:34 GMT