Beta3 bridge
-
This normal state of configuration for bridge?
Beta2->upgBeta3$ ifconfig rl0: flags=8943 <up,broadcast,running,promisc,simplex,multicast>mtu 1500 options=8 <vlan_mtu>inet6 fe80::2c1:28ff:fe01:ff3%rl0 prefixlen 64 scopeid 0x1 inet 10.62.0.3 netmask 0xffffff00 broadcast 10.62.0.255 ether 00:c1:28:01:0f:f3 media: Ethernet autoselect (100baseTX <full-duplex>) status: active ed0: flags=8943 <up,broadcast,running,promisc,simplex,multicast>mtu 1500 inet6 fe80::250:bfff:fe68:4337%ed0 prefixlen 64 scopeid 0x2 inet 10.62.0.3 netmask 0xffffff00 broadcast 10.62.0.255 ether 00:50:bf:68:43:37 media: Ethernet autoselect (10baseT/UTP) pfsync0: flags=41 <up,running>mtu 1348 pfsync: syncdev: rl0 maxupd: 128 lo0: flags=8049 <up,loopback,running,multicast>mtu 16384 inet 127.0.0.1 netmask 0xff000000 inet6 ::1 prefixlen 128 inet6 fe80::1%lo0 prefixlen 64 scopeid 0x4 pflog0: flags=100 <promisc>mtu 33208 bridge0: flags=8043 <up,broadcast,running,multicast>mtu 1500 ether ac:de:48:3e:40:a1 priority 32768 hellotime 2 fwddelay 15 maxage 20 member: ed0 flags=7 <learning,discover,stp>port 2 priority 128 path cost 55 disabled member: rl0 flags=7 <learning,discover,stp>port 1 priority 128 path cost 55 forwarding carp0: flags=49 <up,loopback,running>mtu 1500 carp: MASTER vhid 1 advbase 1 advskew 0</up,loopback,running></learning,discover,stp></learning,discover,stp></up,broadcast,running,multicast></promisc></up,loopback,running,multicast></up,running></up,broadcast,running,promisc,simplex,multicast></full-duplex></vlan_mtu></up,broadcast,running,promisc,simplex,multicast>
I unsure for this
bridge0: flags=8043 <up,broadcast,running,multicast>mtu 1500 ether ac:de:48:3e:40:a1 priority 32768 hellotime 2 fwddelay 15 maxage 20 member: ed0 flags=7 <learning,discover,stp>port 2 priority 128 path cost 55 disabled</learning,discover,stp></up,broadcast,running,multicast>
Sory for new topic
-
OK
this resolveIn Ed0 i change net card
Tomorrow i read about FreeBSD bridge. Bridge interface too, but in webgui this interface not present. And firewall cant filtered them. May be possible add Bridge interface IF them activate?
I understand problem with this. But for user-configuration this is more simplest
-
For success activate bridge
IFCONFIG - all interfaces must be status active (check this)
interfaces must be plugin to active lan hardvare
interfaces cant plug to one switch or make cirkle shemeIn bridge0 all members must be forwarding state.
Need add procedure to webgui for test bridge problem (for begining – with writen me)
Next time i test Firewall with bridge & possoble write about