Everything works except loading a webpage
-
I've deleted the allow all firewall rule on the WAN side and unchecked Allow IPv6. Nothing has changed unfortunatly.
I've also added some more screenshots with the error and captured the packages.
-
You can add images directly here without having to link to an Imgur url, btw.
Everything looks like it should be working. This is a Hail Mary last resort, but I've seen cases of really weird behaviour that simply goes away with a reinstall. For you that should be easy since there is no extra configuration required. Reinstall from scratch, configure your interfaces and then try again. Do NOT add any extra or funny rules until you have learned a bit more about how they work. What you're trying to accomplish should work right out of the box with only NIC configuration required.
-
Okay I'll try that. Can I reformat the drive with the pfsense installer? Or should I just install it on top of the old installation? (sorry for the stupid question).
-
I haven't played with the new installer that much so I can't answer that definitively. You might try the Reset to factory defaults option #4 from the console first.
-
I've already tried the "Reset to factory defaults" and that does not solve the issue unfortunately. I guess I'll try installing it again and hope it will reformat the drive or something.
-
I can't see what else it could be at this point. You have connectivity and DNS. It should work.
-
did you mess with your outbound nat?
Post your outbound nat tab
-
Hi @johnpoz
I've done a complete reinstall of the pfsense system. I haven't touched anything at all.
I have the same issue. Here are the nat settings:
I can ping and nslookup just fine again except load a webpage.
-
I didn't see it in your troubleshooting steps, but did you reboot your ISP modem? And by that I mean, unplug it for at least 10 minutes.
Sometimes ISP modems lock onto an internal MAC address and won't send traffic to anything but that address until you reboot it.
Jeff
-
Hi John.
I've unplugged the modem for 15 min with no power. The issue still persists.
I'm starting to believe me and pfsense are just not meant to be. -
@kimyeti said in Everything works except loading a webpage:
I'm starting to believe me and pfsense are just not meant to be.
Do you have another router/firewall you could try?
Jeff
-
Unfortunately I do not. I have no problem buying a new router, but I'm afraid that I would get home and get the exact same issue. Then I would have two perfectly fine routers and still a broken network :(
-
@kimyeti said in Everything works except loading a webpage:
Unfortunately I do not. I have no problem buying a new router, but I'm afraid that I would get home and get the exact same issue. Then I would have two perfectly fine routers and still a broken network :(
How about your ISP modem? Does it have LAN ethernet ports on the back? If it does, there's a router you could try...
Jeff
-
I do not understand. Do you want to disable bridged mode on the ISP Router/modem? I know that would work because I've used that for 2 years.
But I would have to call my ISP again to switch the MAC address from the WAN interface on the pfsense to the ISP router.
I cannot install pfsense on their equipment.
-
@kimyeti said in Everything works except loading a webpage:
Do you want to disable bridged mode on the ISP Router/modem?
No, you don't have to do that.
Are you sure you're supposed to set your WAN interface to get an IP address via DHCP? On most (and I could count the number of times on one hand) of the bridged WAN connections I've had, they were always static IP addresses, with an upstream gateway manually typed in.
You mention calling the ISP to switch MAC addresses. Did you do that to get the pfsense box online? Did you give them the correct MAC address for the pfsense box? Can they help you with pinging the pfsense box, or verifying that it is even on their network?
I know you can't install pfsense on the ISP equipment. My point in asking about switching back to it was that would tell you if your pfsense box was truly malfunctioning, or if the problem lies somewhere with your ISP. By swapping another router with default configs, if that worked and got you online, your pfsense box would be bad. Get it? :)
Jeff
-
Simple test... sniff on pfsense wan... Have a client try and open a website... Do you see the SYN go out? Do you see the syn,ack come back?
The traffic outbound should be changed to your public IP via the outbound nat, and the source port changed... What does your state table show for the website you tried to access.
In the cable world - when you have place the ISP gateway device in bridge mode wan of pfsense would always be dhcp... And yes in the cable world you always have to powercycle the modem/gateway to free up the mac binding when you change devices.
It could be the isp is preventing access to the mac that is pfsense wan... The can happen when you get a new cable modem... Where you get access but you can not go anywhere other than the registration page of the ISP.. Possible if your resolving vs using the isp dns that your not getting some sort of dns redirect that your ISP does to say hey new device do you want to register it or call 1234, etc. etc..
But if you see the syn go out of pfsense with the correct public IP and you get no answer then the problem is UPSTREAM...
-
"Are you sure you're supposed to set your WAN interface to get an IP address via DHCP?"
According to the ISP guy I spoke with that's how they do it." Did you give them the correct MAC address for the pfsense box?"
The guy repeated it back to me, so I'm 99% sure."Can they help you with pinging the pfsense box, or verifying that it is even on their network?"
We can ping each other just fine."By swapping another router with default configs, if that worked and got you online, your pfsense box would be bad. Get it? :)"
True, but the reason why I got confused is because I would need another router to test with which I don't have at the moment. But it's a good idea and I will buy a cheap pre-configured router and see if that works. If I get the same error then we know for sure It's either the ISP's modem or something else in their end :) -
"Simple test... sniff on pfsense wan... Have a client try and open a website... Do you see the SYN go out? Do you see the syn,ack come back?"
Do you mean sniff with the diagnostic tool "packet capture" in pfsense or maybe Wireshark? I already did a few tests before I reinstalled pfSense where I started the capture tool while trying to load websites on the client machine.
WAN IP = 80.162.60.53
Reddit.com = 151.101.193.140
Google.com = 216.58.207.227Unfortunately I can't do more tests right now because my brother needs to be able to do work from home. I've reversed it back at the moment to get internet.
"And yes in the cable world you always have to powercycle the modem/gateway to free up the mac binding when you change devices."
I've definitely done that to the full extent in pure frustration ;)
"Where you get access but you can not go anywhere other than the registration page of the ISP"
That is a possibility and if that's correct then my ISP has horrible customer service if they fail to mention such crucial details. I'm gonna go for @akuma1x advice first by purchasing a cheap pre-configured router and see if the same issue occurs. Whatever happens from there will rule out a lot. Even though it's not solved yet I just want to say thank you to everybody in the thread for trying to help me.
If you want I'll keep you posted on this thread :)
-
I found the solution to the issue and I just wanted to share what it was.
Short Story: pfSense rocks - my ISP sucks
Long Story:
After connecting a new cheap router I experinced the same issue. The fault must be at the ISP then, but they repeatedly told me that there were no issues in their end. I found the solution by reading a bunch of forum posts on their forum and someone posted if you had port forwards on their router, then it would block those ports in bridge mode. It's a bug in the system. The solution was to reset the router/modem to factory settings and shutdown all power for 10 min. Boom !
Everything worked after that. I appreciate all the help that I got here, cheers.
-
So just to clarify.. You had say tcp 80 forwarded to 192.168.1.100 on their device.
Now you put their device in bridge mode, and you get public IP on pfsense 1.2.3.4 wan... But inbound traffic to your public IP so that pfsense would see it is blocked for tcp 80 and pfsense would never get syn to its wan on tcp 80.
How would that be a problem with accessing websites? Unless you for example ALL ports forwarded in say a DMZ host.. So now when you talk outbound from pfsense to 80 from source port lets say 50452, the return syn,ack to 50452 was being blocked?
You could of clearly seen that with packet capture on pfsense.. You would of seen your syn go out, but no syn,ack back.
