Wireless not allowing connection to internet
-
Have you set up some firewall rules yet? If so, please post, if not, that might be your problem since any interface after the lan and wan have no default rule base (opt##), like pass all.
Hi LostInIgnorance,
There was no rule set by default so i have added the following;
action - pass
interface - OPT1
sourse - any
destination - any
gateway - 192.168.1.1Still no luck, Any ideas?
[edit] looking at the system logs- the traffic is being blocked by
The rule that triggered this action is:
@70 block drop in log quick all label "Default deny rule"
[edit/]
-
try using the below rule without specifying the gateway
action - pass
interface - OPT1
sourse - any
destination - any
gateway - 192.168.1.1Also, have you done any manual setup with nat, or have you left it as the default of pfsense creating the nat rules for you?
Another thing you can try is pinging google.com from the firewall gui directly [Diagnostics>Ping]
EDIT: Are you trying to bridge the wired lan and the wireless? Just wondering since on the wireless (opt1) interface you are specifying the gateway of the lan. If they are two separate networks (like my "pube-lic" wifi is at the house [don't need friends crapboxes screwing up my local lan]) then the gateway does not need to be specified since pfsense uses the wan gateway as its link.
If you're looking to bridge the two so you have lan resources, let me know and I can walk you through how to configure it. -
cheers for the replys LostInIgnorance,
I really appreciate the help! At the moment the pfsense box isn't plugged in but what ill do is post up some screenshots of my config pages tomorrow and hopefully that will be better than me trying to post information.
thanks again
-
Righty, Hopefully these can help.
Lan interface
Opt1 interface
DHCP on Lan
DHCP on opt1
Nat Outbound
Interface Status (WAN has no carrier as i only plugged the box in to get the screenshots)
Wan Firewall rules
LAN Firewall rules
Opt1 Firewall Rules
Opt1 firewall rules expanded
Hope this helps.
-
Yeah, looks like you wanna bridge. When I get home in another hour, I'll post an easier how to, otherwise, see if this makes any sense.
http://forum.pfsense.org/index.php?topic=7946.0 -
One thing that is easy to forget after changing firewall rules is that it is often necessary to reset firewall states after the rule change: see Diagnostics -> States and click on the Reset States tab.
-
Cheers for the help guys, it's very much appreciated!
Yeah, looks like you wanna bridge. When I get home in another hour, I'll post an easier how to, otherwise, see if this makes any sense.
http://forum.pfsense.org/index.php?topic=7946.0I was sure that i tried bridging before but ill have a look through that link later on when i'm back from work and see how it goes
One thing that is easy to forget after changing firewall rules is that it is often necessary to reset firewall states after the rule change: see Diagnostics -> States and click on the Reset States tab.
Ill have a look at that one first before the bridging as it appears alot simpler.
ill let you know how i get on, thanks again
-
Yeah, looks like you wanna bridge. When I get home in another hour, I'll post an easier how to, otherwise, see if this makes any sense.
http://forum.pfsense.org/index.php?topic=7946.0Just been having a look at Bridging the OPT1 to the LAN and it appears the DHCP is only functioning on LAN so anything that tries to connect to the wireless will not get an IP so doesn't connect.
OPT1 interface (ath0)
Status associated
MAC address 00:1f:3a:52:ef:58
IP address 0.0.0.0
Subnet mask 255.0.0.0
Gateway 192.168.1.1
Media autoselect mode 11g <hostap>Channel 1
SSID LocalWAP
In/out packets 64/409 (15 KB/283 KB)
In/out errors 127/380
Collisions 0
Bridge (bridge0) learning</hostap> -
Oh, Nevermind - after i posted the above i managed to fix it!
I turned off "Allow intra-BSS communication"
Under - "General configuration" Changed 'Type' from DHCP to Static and added an ip address then it is now working. -
I forgot to say - thatnks for the help on this one guys but i've decided to just stick with my current wireless router - there's just too much messing about to be done to get pfsense working properly - after i got wireless working, VNC stopped working on my internal network