Opnevpn cliente e site to site
-
@viragomann hello but there are already these tunnels
on the pfsense server 192.168.2.252 (where you connect with the client) there is the tunnel 192.168.222.0/24 and then there is the local network 192.168.2.0/24 which is the local network of the pfsense if I put that remote then the local no longer works
remotely there is another server which is 192.168.3.250 and it works fine, and the configuration is the samethe strange thing is that if I pin server 192.168.111.250 from server 192.168.2.250 it works, if instead I connect with opevpn client to site from an external office it doesn't work I only see the 192.168.2.x network and the 192.168.3 network .x but the 192.168.111.x network is not working
-
@miami71it said in Opnevpn cliente e site to site:
on the pfsense server 192.168.2.252 (where you connect with the client) there is the tunnel 192.168.222.0/24 and then there is the local network 192.168.2.0/24 which is the local network of the pfsense if I put that remote then the local no longer works
Nice. But I suggested you to add 192.168.111.0/24.
remotely there is another server which is 192.168.3.250 and it works fine, and the configuration is the same
Oh, that's a total new network. You didn't mention above.
the strange thing is that if I pin server 192.168.111.250 from server 192.168.2.250 it works, if instead I connect with opevpn client to site from an external office it doesn't work
This seems not strange to me, this let me assume that you're missing routes. And therefor I requested you to do some additional settings.
-
@viragomann where do you tell me to add 192.168.111.250/32 there is currently written 192.168.2.0/24, can you add both? or a single network?
sorry I didn't write about another remote server as I thought it was not relevant, basically there are two remote networks, one works and one doesn't.
the configurations are identical only obviously the ip address and the tunnel changes
-
@miami71it said in Opnevpn cliente e site to site:
where do you tell me to add 192.168.111.250/32 there is currently written 192.168.2.0/24, can you add both? or a single network?
Yes, the networks have to be in CIDR notation and comma separated. Should look like this line:
192.168.2.0/24,192.168.111.250/32 -
@viragomann .it doesn't work from this error
The following input errors were detected:
The field 'IPv4 Tunnel Network' must contain a single valid ipv4 CIDR range.
-
@miami71it
So what did you try to enter, dude?
The line what I suggested should work at all. -
@viragomann ok I inserted it, I restarted the service but the problem remains I connect to the VPN remotely and the server 192.168.111.250 does not pin it and I do not reach it
other ideas?
-
@miami71it
Okay, for deeper investigation, please post the IPv4 Routing tables of both pfSense (Diagnostics > Routes) and of the client, also the firewall rules of the VPN interfaces and content of Status > Interfaces. -
@viragomann I am attaching a word document with the info yoPFSENSE.zip u requested
-
@miami71it
So at the remote site (192.168.111.252) you're still missing the entries, which I suggested to add above.In the OpenVPN peer-to-peer client the "IPv4 Remote Networks" box has to look like this
192.168.2.0/24,192.168.3.0/24,192.168.222.0/24However, the routing table on 192.168.2.252 look somewhat odd. You should probably reboot the machine.
-
@viragomann perfect now with your directions it works great
I THANK YOU
-
This post is deleted!