pfSense 22.05 breaks VLANS, restoring pfSense 22.01 fixes the issue

NRgia

@stephenw10 said in pfSense 22.05 breaks VLANS, restoring pfSense 22.01 fixes the issue:

What I expect to see if you have any sort of priotiy tagging on a VLAN is something like this:
18:23:28.004183 00:90:7f:b4:38:fa (oui Unknown) > 90:ec:77:1f:8a:5f (oui Unknown), ethertype 802.1Q (0x8100), length 102: vlan 1001, p 4, ethertype IPv4, AP300.stevew.lan > 10.101.0.1: ICMP echo request, id 10296, seq 2, length 64
18:23:28.004212 90:ec:77:1f:8a:5f (oui Unknown) > 00:90:7f:b4:38:fa (oui Unknown), ethertype 802.1Q (0x8100), length 102: vlan 1001, p 0, ethertype IPv4, 10.101.0.1 > AP300.stevew.lan: ICMP echo reply, id 10296, seq 2, length 64
There I have set egress tagging in OpenWRT to map 0 to 4 so pfSense sees it on the incoming traffic. But there is only one set of tags.

Just a question, what we except to happen if set some priority to VLANS form pfSense? I know the documentation says to leave that on zero?

I don't know how to provide what you want to see.

NRgia

@stephenw10
From the switch in order to apply priority tags, I must disable the 802.1p mode, and apply per port, for the AP I don't see any option to apply a priority without buying a switch from Ubiquiti. I can provide you some screenshots.

This is how it looks for a VLAN:
https://imgur.com/a/3gBCTIL

johnpoz

@nrgia I have unifi APs, and yeah I just looked I do not see anywhere to set priority on a vlan at all.

Running the lastest firmware on APs 6.2.27 and 7.2.87 controller software. I could try moving to the new UI vs legacy that I use.

NRgia

@johnpoz I'm using the new UI, don't bother. If you don't buy the whole ecosystem you can do so much. But a four eyes check doesn't do any harm. Thank you

NRgia

@nrgia How your networks are configured in the AP, I mean in the Networks tab? Are the VLANS set to VLANs only network? Or how? Thank you

stephenw10

@nrgia said in pfSense 22.05 breaks VLANS, restoring pfSense 22.01 fixes the issue:

Just a question, what we except to happen if set some priority to VLANS form pfSense?

Applying it on the VLAN should show in the VLAN tag outbound as expected like:

19:16:32.694149 00:90:7f:b4:38:fa (oui Unknown) > 90:ec:77:1f:8a:5f (oui Unknown), ethertype 802.1Q (0x8100), length 102: vlan 1001, p 4, ethertype IPv4, AP300.stevew.lan > 10.101.0.1: ICMP echo request, id 10347, seq 1, length 64
19:16:32.694172 90:ec:77:1f:8a:5f (oui Unknown) > 00:90:7f:b4:38:fa (oui Unknown), ethertype 802.1Q (0x8100), length 102: vlan 1001, p 3, ethertype IPv4, 10.101.0.1 > AP300.stevew.lan: ICMP echo reply, id 10347, seq 1, length 64

pfSense sets prio 3 and the AP replies prio 4.

Try using port mode on your switch then. If you can set anything that appears in the pcap it might be useful.

Steve

NRgia

@stephenw10 said in pfSense 22.05 breaks VLANS, restoring pfSense 22.01 fixes the issue:

ng that appears in the pcap it might be useful.
Steve

First I selected Normal priority on the switch for the pfSense port and the AP port. The switch don't have numbers. Also I select 3 for VLAN 20 on pfSense.

I got this:
tcp_dump_vlan_prioriry_pfsense_and_switch.txt

I lost connection after doing this, I could only connect to devices via their IPs

Then i reset the priority from VLAN 20 from pfSense to zero(0) and I got this:
tcp_dump_vlan_prioriry_on_switch.txt

stephenw10

Those pcaps were on the mirror port again?

In both those pcaps there are no packets from pfSense at all....

Do you still see outbound packets if you tcpdump on ix2 on pfSense in either of those setups?

Steve

NRgia

@stephenw10 said in pfSense 22.05 breaks VLANS, restoring pfSense 22.01 fixes the issue:

Those pcaps were on the mirror port again?

In both those pcaps there are no packets from pfSense at all....

Do you still see outbound packets if you tcpdump on ix2 on pfSense in either of those setups?

Steve

Ok I redone the tests:
First test:
Steps:

Set priority to 3 in pfSense to VLAN 20
Set Normal Priority in the switch to the port where the AP is connected
Set High priority in the switch to the port where pfSense LAN side is connected.
Done a tcpdump from pfSense.
Results:
tcpdump_priority_set_to pfsense_and_switch.txt

As you can see, only the priority (3) set in pfSense is intercepted.

Second test:

Removed priority 3 set in pfSense to VLAN 20
Left the Normal Priority in the switch to the port where the AP is connected
Left the High priority in the switch to the port where pfSense LAN side is connected.
Done a tcpdump from pfSense.

Results:
tcpdump_priority_set_to_switch.txt

I don't see anu priorities besides (p0) when done from the switch.

I hope the steps are ok, now.

stephenw10

Hmm, OK.

Can I assume traffic was failing during those tests?
We see no ARP replies to pfSense's queries and it looks like one way traffic from the clients.

NRgia

@stephenw10 said in pfSense 22.05 breaks VLANS, restoring pfSense 22.01 fixes the issue:

Hmm, OK.

Can I assume traffic was failing during those tests?
We see no ARP replies to pfSense's queries and it looks like one way traffic from the clients.

Correct, I could communicate only via IP with pfSense. Only that worked.

johnpoz

@nrgia said in pfSense 22.05 breaks VLANS, restoring pfSense 22.01 fixes the issue:

Correct, I could communicate only via IP with pfSense. Only that worked.

If you were not getting arp replies then wouldn't work even with IP..

NRgia

@johnpoz said in pfSense 22.05 breaks VLANS, restoring pfSense 22.01 fixes the issue:

@nrgia said in pfSense 22.05 breaks VLANS, restoring pfSense 22.01 fixes the issue:

Correct, I could communicate only via IP with pfSense. Only that worked.

If you were not getting arp replies then wouldn't work even with IP..

If you say so

johnpoz

@nrgia said in pfSense 22.05 breaks VLANS, restoring pfSense 22.01 fixes the issue:

If you say so

Not something making up dude - if you can not arp for the mac of something, it is impossible to talk to it even with an IP.

Mac is what is used to talk to something on a network.. Just not possible if you do not have the mac to talk to.

As Steve mentioned

We see no ARP replies to pfSense's queries and it looks like one way traffic from the clients.

Look at your arp table on your client, arp -a will show you the full table.. If there is no mac for an IP then your not going to talk to it.

NRgia

@johnpoz said in pfSense 22.05 breaks VLANS, restoring pfSense 22.01 fixes the issue:

@nrgia said in pfSense 22.05 breaks VLANS, restoring pfSense 22.01 fixes the issue:

If you say so

Not something making up dude - if you can not arp for the mac of something, it is impossible to talk to it even with an IP.

Mac is what is used to talk to something on a network.. Just not possible if you do not have the mac to talk to.

As Steve mentioned

We see no ARP replies to pfSense's queries and it looks like one way traffic from the clients.

Look at your arp table on your client, arp -a will show you the full table.. If there is no mac for an IP then your not going to talk to it.

The host, the switch and pfSense have static IP. If it did not work, how I could provide the tcpdump?
As you can see the tcpdump is from ix2 interface,from pfSense, you can see that priority 3 set from pfSense.
Is this discussion productive, in any way ? Do you think I'm lying ?

johnpoz

@nrgia said in pfSense 22.05 breaks VLANS, restoring pfSense 22.01 fixes the issue:

The host, the switch and pfSense have static IP. If it did not work

Then there must be an mac listed in the arp table.. Keep in mind that connecting to pfsense on its lan interface, and then sniffing on a different interface has little to do with if the clients on that other interface or vlan can arp for stuff..

You might see the arp request go out, or come in, but if you do not see replies then those devices that are arping for each other are not going to be able to talk to each other - period.

Don't think anyone is lying - just trying to understand all the pieces to the puzzle. I do recall looking at some of the sniffs and while I saw arp request, I don't recall ever seeing any answers.

NRgia

@johnpoz

So I did like that:

I was connected via ssh to pfSense
Set the priority to 3 from pfSense from GUI
Set the priority from the switch
After that all the hosts lost communication besides pfSense and the host I was running the test
I performed a tcpdump on pfsense LAN interface ix2
I could also connect to pfSense GUI via it's LAN IP, but not with it's domain name.

Other technicalities I don't know how to explain. If the test wasn't good, then this is how I understood to reproduce it, following what Steve has told me.

stephenw10

Right but the LAN interface here is ix2 unatgged, no VLAN right?

The pcap only captured VLAN tagged traffic, the GUEST interface, and it looked like that was failing?

It appeared as though the priority setting in the switch was in fact filtering the traffic in some way rather than applying tags. Which might well be what it's supposed to be doing in that mode.
Are you able to test that on your switch @johnpoz?

johnpoz

@stephenw10 yeah my switch is still up, I could setup some vlans to go through it.

What exactly would you like me to test, doing port based qos? vs the 802.1p

Let me add the vlans to the switch, so I can just connect my AP to it, it has 1 untagged vlan and 3 other tagged vlans. 2 of which are tagged all the way to pfsense, and another that has its own uplink to pfsense that is untagged.

stephenw10

Yeah any test you can do there to see what those QoS settings it has do.

I expected it to apply tags but I have no idea if that's inbound or outbound on the ports.

However it looks more like it's filtering based on the tags from those last pcaps. No ARP replies to queries sent as p 3.