Latest pfsense+ 23.01 beta freezes on Hyper-v
-
I may try with a fresh install of Windows Server 2022 when 23.01 is released.
I'm curious; my VM configuration dump says the VM has two COM ports, but Hyper-V doesn't pass the physical one I have to the VMs - third party software is required for that. This isn't exposed in the Hyper-V Manager GUI. Does your VMCX configuration file show ComPort1 and ComPort2?
-
@andrew_241 said in Latest pfsense+ 23.01 beta freezes on Hyper-v:
Does your VMCX configuration file show ComPort1 and ComPort2?
I can't tell because I don't know any of the syntax of you command. I am just an advanced home user, don't know nothing about powershell etc.
-
My VM config that works also shows the COM ports, so that's unlikely to be related.
One of our TAC crew who could reproduce this noticed that they could get theirs to boot if they removed the DVD drive from the VM, so that's something else to try.
Mine works with the DVD drive attached (and with no media mounted). Theirs appeared to be set the same but failed until they removed it.
-
Sadly but removing DVD drive did not solve the problem. Even vm that booted successfully after upgrade started displaying same behavior after some reboots. There was the confusion that it only crashing with console open when booting, that seems no longer be the case. It seems that sometimes it just boots after upgrade, but breaks later and sometimes it just broken as soon as you upgrade.
-
Might be a long shot, but do your configurations on those VMs have the serial console enabled even though they don't have COM ports mapped in Hyper-V?
There is a known issue in that area with FreeBSD on Azure Gen2 VMs but I wouldn't think it would manifest on local Hyper-V setups since even though the VM contains COM port configurations it doesn't actually have any uart controllers or serial ports visible to the guest.
-
Most likely related thread
https://forum.netgate.com/topic/176572/hyper-v-upgrade-from-22-05-to-23-01-b-20221217-1429-fails-to-boot/7Will test rc tomorrow.
Also 2.7 ce builds worked ok
-
Tried installing 23.01 rc
2.6ce to 22.1 then 22.5 and 23.1 rc
First boot after upgrade successful then tried rebooting same pattern crashing
First boot after upgrade
Reboot
-
I have yet to see an answer to my last question:
Do these VMs have the serial console option enabled in settings? (System > Advanced, Admin Access tab)? If so, disable it before upgrading.
Remember: Upvote with the 👍 button for any user/post you find to be helpful, informative, or deserving of recognition!
Need help fast? Netgate Global Support!
Do not Chat/PM for help!
-
@jimp they don't have serial enabled at least when it booted after upgrade I checked in ui and serial check box was unchecked if that's what you mean.
-
@jimp said in Latest pfsense+ 23.01 beta freezes on Hyper-v:
Do these VMs have the serial console option enabled in settings? (System > Advanced, Admin Access tab)? If so, disable it before upgrading.
Mine doesn't and I never had any problem. I don't even know what a serial console is.
-
If you can, look at
/boot/loader.confand/boot/loader.conf.localand post the contents from before the upgrade (or the first boot after if that works would be even better).The similar problem that happens in Hyper-V is definitely loader related, but it has to do with serial output. We have a potential fix but since it's in the loader it's a bit too disruptive to get into this release at this stage. Even though Hyper-V doesn't have serial consoles per se in Gen2 it may still interfere. Most of us still can't even reproduce the boot failure here in Hyper-V which is a bit maddening.
-
@jimp
Got contents of loader.conf couldn't find loader.conf.local (sorry for picture format was easiest to grab this way)
This is from 22.5 before upgrade to RC. Rolled back to vm snapshot.
(Tried upgrade to 23.1 again but this time it crashed even on first boot)
Contents of boot folder no local file
-
There isn't always a
.localfile unless someone created it manually, but it's good to check for it in case it is there. Nothing stands out in that loader config, definitely no sign of serial or console config which is what I was curious about.Did you check for and remove any optical drives from that VM? We have one person here who only saw it crash/fail to boot with an optical drive on the VM.
-
@jimp
No DVD drive
-
@bob-dig said in Latest pfsense+ 23.01 beta freezes on Hyper-v:
Maybe MS is just doing MS things and it depends on the age of your Windows Installation and what not... I have problems running a service in a debian VM in Hyper-V, I always have to boot it twice.
After this MS-patchday my problem with the debian VM is gone. But I had some other changes too... it is a possibility. -
J jimp moved this topic from Plus 23.01 Development Snapshots (Retired) on
-
Just quick update. The official release of 23.01 still does not boot in Hyper-v.
Tried on 2 different hosts (Both Windows server 2022 standard all updates installed) still getting stuck at boot. -
@vbjp said in Latest pfsense+ 23.01 beta freezes on Hyper-v:
Just quick update. The official release of 23.01 still does not boot in Hyper-v.
Tried on 2 different hosts (Both Windows server 2022 standard all updates installed) still getting stuck at boot.same issue while updating with all settings/packages/configuration in place.
If you open the Hyper-V machine and check the logs while updating, you will see a log saying disk out of space, and the system continues, as it finished. I believe that's the reason. corrupt/partial update.
Negate minimum requirement says you needs a minimum of 8GB. (mine was 5GB fixed)
You can expand the vhdx file and shell into pfsense and resize the partitions.
Here is a good link on how adjust your disk after expanding the vhdx
https://people.freebsd.org/~rodrigc/doc/handbook/disks-growing.htmlOr
- backup your pfsense
- create a new vhdx disk (I set mine to 15GB)
- install pfSense-CE-2.6.0
- update to pfsense + 22.05 then 23.01
- restore the backup.
I can confirm it worked for me.
Cheers. -
@fiblimitless my pfsense vm has 30gb (other one has 60gb both not booting) drive assigned to it is that not enough? Possibly not same problem.
-
@vbjp shell into pfsense check your partitions: gpart show
what do you have?
-
S stephenw10 referenced this topic on
-
S stephenw10 referenced this topic on
-
Yes, is the disk space error actually whilst updating the main root filesystem or possibly the EFI partition?
