PortForward Not woking no matter what i do
-
@dark_prophet I posted them...
you sure that IP is correct.. if pfsense can not talk to that IP, then it can not send on the traffic - since it doesn't know the mac address of it.
I posted the portforward and the rule that it generates on my wan..
The rules on your wan are evaluated top down, if you have some rule that blocks before your allow then no it would never work, if you have some rule on floating that would block, again it wouldn't work.
-
ok i think you got it that could be the problem LAN interface is not getting anything
i ping my Plex server on 32400 port on WAN and LAN and i get an output
but now on 2302. what could be the issue now ? any ideas ?
-
@dark_prophet have no idea you haven't posted your wan rules, nor if you have any rules in your floating. Nor again that pfsense can even talk to this IP you want to send 2302 too..
Can pfsense ping this IP your trying to forward too, does it show mac address?
If pfsense does not have the mac address of where to send traffic for this IP - then no it can not send it, even if your port forward and wan rules would allow it.
You have different IPs in your plex forward vs this 2302 forward, one is to a .99 the other is to a .98 is that a typo? And your trying to send 2302 to your plex box as well?
-
-
-
@dark_prophet what advanced thing did you do on that 2302 rule - see the gear on it.. Also I see no hits on that rule.. see the 0/0 B in the states - if you had sent traffic from the outside that rule matched on it would be something other than 0/0 like see your plex rule above it.
-
there it shows MasterPC
-
@dark_prophet all good info.. But what is that Gear Settings on that rule - means you did some sort of advanced filter on it.. Also it shows 0/0 hits on it - do you have something in floating rules that would prevent traffic from ever hitting the interface (wan) rule..
Also that shows its on a vlan, not your lan - if you sniffed on lan you wouldn't see traffic going to it..
-
that's the sloppy state that i was trying to make it work lol
i did have something on flotting rules but i deleted everything and started from scratch -
problem LAN interface is not getting anything
Did you do the packet capture on the correct interface - your lan would never see anything because from your arp table that IP is on your main_vlan interface.
-
When i capture in MAIN_VLAN not output
when i capture on WAN i see trafficmy Plex server is on the same interface and i see output on all interfaces
-
@dark_prophet well that doesn't make a lot of sense.. Are you showing that wan rule trigger when you send traffic - or is it still at 0/0
-
thats why im scratching my head here lol
still showing 0/0 on everythingi wonder if the Main_vlan might be conflicting with something else.
-
@dark_prophet said in PortForward Not woking no matter what i do:
i wonder if the Main_vlan might be conflicting with something else.
No that has nothing to do with it... I just sent traffic to 2302 on your IP.. Does the rule show any evaluations?
Les see your port forward rules not the individual rules - all of them, want to see the order, did you place anything in the advanced source for that 2302 rule?
-
still nothing
where did i forgot to cover my ip address lol
-
@dark_prophet you covered the last octet, but I got it from the ip you talked to the forum from.. As mod I can see that.
I had to assume that was your IP, since the first 3 octets matched.
So you still don't see any evaluations on that rule - shows 0/0 then yeah something is wrong.. You sure you have no rules in floating... You sure your rules reloaded after changing say floating - you say you removed stuff.. Do a reload of your filters..
-
lol forgot
im taking all the pictures now
-
do a reload
Did you copy and paste any rules - there was some issue going around where rules that were copied got the same ID..
-
ok i did filter reload now
-
i deleted every rules and started clean again
