ATT Uverse RG Bypass (0.2 BTC)

GPz1100

@stephenw10 Use of openssl 3.0 introduced other issues requiring some additional parameters in later pf versions.

I've attached a txt containing my notes from the discord discussion on the issue.

jasonsansone

I upgraded to 23.09.1 and changed to using the method detailed here. However, wpa_cli status reports "connecting" and "unauthorized". The exact same hardware and certs authenticate fine on 22.05 using the old pfatt wpa_supplicant script. Any recommendations?

dreamdenizen

@jasonsansone

I put my certs and wpa_supplicant.conf file in /root/wpa and used the following earlyshellcmd and shellcmd. Worked perfectly fine on 23.09.1 until I bailed to OPNsense last week. Same commands are also working great on OPNsense 23.7.10 using rc.syshook.d scripts.

earlyshellcmd

ifconfig igb0 ether "xx:xx:xx:xx:xx:xx" && wpa_supplicant -s -dd -B -Dwired -i igb0 -c /root/wpa/wpa_supplicant.conf -P /var/run/wpa_supplicant.pid && sleep 10 && wpa_cli logon

Plug your RG ethernet MAC in place of the xx:xx... above

shellcmd

wpa_cli logoff && sleep 10 && wpa_cli logon

the -s and -dd flags in my earlyshellcmd will cause wpa_supplicant to push all debug log activity to syslog, so look there for clues as to what's happening if you still can't auth.

You may have caused your ONT to flag due to too many failed auth attempts, so make sure to push the reset pin in on the back before your first boot with these commands.

Good luck.

jasonsansone

@dreamdenizen can you please post your .conf just so I can verify? Thank you. Your method is what I was testing, except I will enable debug logging to better investigate. I had it working once, and then it stopped, which lead me to also suspect I got flagged for too many repeat authentications. Except it’s strange that a reboot into the old boot environmental using the supplicant script works. I would have thought that if I was blocked or suspended, it would fail regardless of method.

dreamdenizen

@jasonsansone your flags may vary based on what was extracted from your BGW210-700 or NVG so I would not recommend changing anything produced by the devicelocksmith extraction tool. My wpa_supplicant.conf is exactly what was spit out by the tool with the addition of

ctrl_interface=DIR=/var/run/wpa_supplicant

to account for running patched versions of wpa_supplicant prior to vlan0 handling being added to mainline. That added line works fine with mainline as well, so I never removed it.

ctrl_interface=DIR=/var/run/wpa_supplicant
eapol_version=1
ap_scan=0
fast_reauth=1
network={
        ca_cert="/root/wpa/CA.pem"
        client_cert="/root/wpa/Client.pem"
        eap=TLS
        eapol_flags=0
        identity="xx:xx:xx:xx:xx:xx" # Internet (ONT) interface MAC address must match this value
        key_mgmt=IEEE8021X
        phase1="allow_canned_success=1"
        private_key="/root/wpa/PrivateKey.pem"
}

jasonsansone

@dreamdenizen thank you. Unfortunately the originally extracted conf has been lost. I was trying to avoid doing the extraction process again.

jasonsansone

Here is the syslog output:

Dec 23 08:38:29 pfsense pfatt[63277]: starting wpa_supplicant... Dec 23 08:38:29 pfsense wpa_supplicant[63663]: Successfully initialized wpa_supplicant Dec 23 08:38:33 pfsense pfatt[71584]: wpa_supplicant running on PID 70876... Dec 23 08:38:33 pfsense pfatt[72244]: setting wpa_supplicant network configuration... Dec 23 08:38:33 pfsense wpa_supplicant[70876]: igb0: Associated with 01:80:c2:00:00:03 Dec 23 08:38:33 pfsense wpa_supplicant[70876]: igb0: CTRL-EVENT-SUBNET-STATUS-UPDATE status=0 Dec 23 08:39:34 pfsense wpa_supplicant[70876]: igb0: CTRL-EVENT-EAP-FAILURE EAP authentication failed Dec 23 08:39:48 pfsense wpa_supplicant[70876]: igb0: CTRL-EVENT-EAP-STARTED EAP authentication started

And here is the output from wpa_cli status:

`wpa_cli status
Selected interface 'igb0'
bssid=01:80:c2:00:00:03
freq=0
ssid=
id=0
mode=station
pairwise_cipher=NONE
group_cipher=NONE
key_mgmt=IEEE 802.1X (no WPA)
wpa_state=ASSOCIATED
address=74:8a:0d:5f:be:21
Supplicant PAE state=CONNECTING
suppPortStatus=Unauthorized
EAP state=IDLE
uuid=666db3f9-54bb-5d96-8859-3fd4bbaa9546

wpa_cli status
Selected interface 'igb0'
bssid=01:80:c2:00:00:03
freq=0
ssid=
id=0
mode=station
pairwise_cipher=NONE
group_cipher=NONE
key_mgmt=IEEE 802.1X (no WPA)
wpa_state=ASSOCIATED
address=74:8a:0d:5f:be:21
Supplicant PAE state=HELD
suppPortStatus=Unauthorized
EAP state=FAILURE
uuid=666db3f9-54bb-5d96-8859-3fd4bbaa9546`

jasonsansone

Extracted certs and conf from RG again. Used exact conf parameters and certs. Tested with and without PCP 1 and/or -vlanhwfilter. Same result.

dreamdenizen

@jasonsansone is that mac address listed in your post the MAC of the RG ethernet? If not, make sure to override the MAC address in Interfaces > WAN with that of your ethernet RG. I also recommend redacting it in your last post.

GPz1100

@jasonsansone Did you read my comments in post # 544?

jasonsansone

@dreamdenizen Good point on redacting, but it will no longer let me edit the post. Yes, the MAC is what was provided in the extracted conf and is also written on the RG. I have used the same MAC in pfatt.sh for years. Do I need to override the MAC in Interfaces > WAN in addition to setting it with ifconfig in the script?

@GPz1100 I attempted to, but admittedly wasn't able to fully track. I understand something with openssl has changed in 23.09, but it appears others have been successful using the same release. I may need an idiots guide to 23.09.1 because I have thus far failed.

Thank you both!

dreamdenizen

@jasonsansone mine wouldn't work without the MAC override in Interfaces > WAN

GPz1100

@jasonsansone I haven't tested the new pf versions yet. Will be starting my migration project in the next few weeks.

The details are fairly self explanatory I thought. Basically openssl disables certain weaker ciphers. The config file re-enables them for the wpa_supplicant session. Depending on which wpa_supplicant is in use, this is either done simply through the wpa_supplicant.conf file (example at the end of the file), or through a config file for openssl that's referenced in the command line launching wpa_supplicant.

@dreamdenizen Mac for wpa_supplicant doesn't have to be that of RG, or even RG where certs came from. What matters is the mac in wpa_supplicant.conf file match that of the wan interface mac requesting dhcp. Otherwise, you'll get eapol authentication, but never received an IP because of the mismatch.