Transparent firewall

hoba

Use a dummy adress there. it just needs to have an IP for some reason.

fnemo

Ok, I think I worked to much today ???

So, lets resume,

on WAN, i select my dummy address (ie: 0.0.0.0/32) and gateway (the ip of the real gw)
on LAN, i select the IP I wish for the bridge and I bridge it to WAN

Then I don't see … Maybe I should sleep and re read manual :/

hoba

Nope:

1. Set a real IP on WAN and gateway (as this interface is the one the other gets bridged to). You will access your webgui by that IP from LAN-side. (If your WAN-IP-Range is inside a private range uncheck "block private IP range")
2. select bridge at your LAN interface and give THAT ONE a dummy IP (like 10.10.10.10/32).
3. Access your webgui by the WAN IP coming from your LAN-side and set up your rules.

Good night ;D

fnemo

I slept well . Now I can work again on it :p

rds_correia

@fnemo:

I slept well . Now I can work again on it :p

So tell us, did it work, huh? did it work? ;D
If you get that to work you could make us a nice tutorial with wink, what do you say?
Cheers

fnemo

In fact it fails. Since I'm using a Shuttle XPC as the firewall, I order a double interfaced network card so I'll have 3 NIC and configure WAN, LAN and OPT.
WAN <-> OPT as a bridge on a certain IP
LAN as control interface.

Once I succeed I'll try to write some kind of tutorial . but for now, I just gave up about a bridge with pfSence on a 2 NIC setup.

hoba

Sorry, we had a bridge bug in the latest version. Please try again with the upcoming version (ETA some minutes/hours).

fnemo

Will check that then ;)

fnemo

I justed DL the 96.2 iso … and it seems buggy . I DL twice on different computers, burned the same ...
When I boot on the disc, I get weird sound from the CD (no problem with another CD) and when it read the acd0 informations, several error occurs.

I'll retry tomorrow, some other work to do today ...

sullrich

This error report is of no use. Next time write down the errors.

fnemo

Ok, I downloaded and burned a new ISO 96.2 from today on one of the mirrors. Installed. Configured.

Then, I created my bridge, deactivated NAT reflections … AND THERE IT WAS !

I rebooted to check something in the BIOS (didn't change anything though) ... and on reboot, configuration was there ... but no more bridge working. I don't have time to double check today so i'll do it tomorrow but that's quite annoying :/

dvserg

OK, i'm build new bridge configuration
One moment - Lan mask (must be 32) take many my time.
My bridge dont work along i not memory this mask settings.

Second moment - if i set any dummy address in Lan (not WAN address) - filter reload progress give error in [].. - what this i don't understand. But only i setup In LAN address IP= WAN address or mask=32 - all filter reload update normally

Please set in GUI avtomatic update LAN IP = WAN IP but only mask=32. This must leave many errors.
May be disable IP setting edit field LAN ip for BRIDGE mode?
And other any Bridged internal interfaces (OPT and etc)?

jeroen234

on wan set a real ip adress this is the interface you will conect to

on lan set a ipadress it don't make out wat
it wil be ignord when you bridge it with youre wan

make sure youre on beta4 with the updates

jeroen234

list of interfaces for bridging

wan - lan wan ipadress
lan - opt1 lan ipadress
opt1 - opt2 opt1 ipadress
wan - opt1 wanipadress
opt1 - wan - lan wanipadress
etc

list of interface weight
wan-lan-opt1-opt2 etc
interface with most weight is the ipadress that will work after the bridged melting

dvserg

Beta 4 updated, Bridge mode ON
If i set Lan any other address - i can ping them ( 2 address of firewall present!)
And - periodical error update rules + shaper problem

Now i Begining test what i setup new (with prevous my post)
7 filtersupdate processes pass without errors (i dont change eny rule - only Edit-Save-Apply)
And shaper perhaps work too - this needs more testing.

hoba

The shaper won't work in a bridging configuration.

dvserg

This conceptual? Or in future shaping bridge possoble?

ps. I wanted use bridge(Or equivalence) + shapping + proxy in one system :(

hoba

It's a limitation. Not sure if there is a way to work around it. However, it won't be included in 1.0 and there is no promise that it will be in 1.1.

dvserg

OK
If this can be in future - i very glad.
Thks.