Fix the VPN IPSEC Dead Peer Detection in 1.2.2 or 1.2.3 {$200}

[kapara]

Could it be something to do with the version of racoon?  I could not find much info about it besides a project called Kame..but that did not tell me much.

[kapara]

I have another tunnel between this 1.2.2 and another 1.2.2 and the tunnel has no problem coming back up.  But others have complained about it so there is no consistency.

[jimp]

@kapara:

Could it be something to do with the version of racoon?  I could not find much info about it besides a project called Kame..but that did not tell me much.

That's possible, which is why I want to try it against 2.0 as well. They are both running the same version of ipsec-tools (http://ipsec-tools.sourceforge.net/) though:

from 1.2.3:
May 11 12:33:07 pfsense-123test racoon: INFO: @(#)ipsec-tools 0.7.1 (http://ipsec-tools.sourceforge.net)

from 2.0:
May 11 11:32:58 pfSense-20test racoon: INFO: @(#)ipsec-tools 0.7.1 (http://ipsec-tools.sourceforge.net)

There is a slightly newer version of ipsec-tools (0.7.2) out, but I don't see any details release notes on the web site that state what bugs were fixed.

[jimp]

It appears that what I thought was the DPD packet may have been Cisco's IPSec keep-alive. I disabled that, and left DPD enabled on the pfSense side, and I see no regular traffic on the tunnel.

That makes me think that either DPD isn't being turned on, or it isn't being negotiated properly for the tunnel.

With Cisco's Keep-Alive turned on, I get:
May 11 15:41:44 pfsense-123test racoon: INFO: received Vendor ID: CISCO-UNITY
May 11 15:41:44 pfsense-123test racoon: INFO: received Vendor ID: draft-ietf-ipsra-isakmp-xauth-06.txt
May 11 15:41:44 pfsense-123test racoon: INFO: received Vendor ID: DPD

With it disabled, I get:
May 11 16:26:21 pfsense-123test racoon: INFO: received Vendor ID: CISCO-UNITY
May 11 16:26:21 pfsense-123test racoon: INFO: received Vendor ID: draft-ietf-ipsra-isakmp-xauth-06.txt

That makes me wonder if, perhaps, the Cisco side really doesn't support DPD as well as it claims to. I'm not sure if there is some other mechanism to signal racoon when something else fails (i.e. the keepalive ping) to reload a specific tunnel. That would probably be more reliable than DPD since that must be supported by both sides.

Why this works for some vendors/devices and not others is also puzzling…

[kapara]

Then why is it that when I reboot my concentrator the pfSense does not respond as seeing the tunnel go down at all but stays green?

[jimp]

@kapara:

Then why is it that when I reboot my concentrator the pfSense does not respond as seeing the tunnel go down at all but stays green?

That is what I'm trying to figure out… :-)

As you said, when both sides are pfSense, it seems to work. I'm wondering if the "invalid SPI" reply generated by the Cisco is broken in some way (or racoon's parsing thereof) such that it doesn't pick up on the fact that the tunnel traffic is being rejected.

[kapara]

Version history: –-------------- 0.7.1 - 23 July 2008 o Fixes a memory leak when invalid proposal received o Some fixes in DPD o do not set default gss id if xauth is used o fixed hybrid enabled builds o fixed compilation on FreeBSD8 o cleanup in network port value manipulation o gets ports from SADB_X_EXT_NAT_T_[SD]PORT if present in purge_ipsec_spi() o Generates a log if cert validation has been disabled by configuration o better handling for pfkey socket read errors o Fixes in yacc / bison stuff o new plog() macro (reduced CPU usage when logging is disabled) o Try to works better with huge SPD/SAD o Corrected modecfg option syntax o Many other various fixes…

[kapara]

That is all foreign to me but maybe it has something to do with the problem.

[jimp]

I'll have to look at it more tomorrow, but I might be able to see if bumping ipsec-tools to 0.7.2 might help things along.
Can't promise anything though.

[drees]

Those aren't the changes in 0.7.2, but the changes in 0.7.1.  Here are the changes in 0.7.2:

0.7.2 - 22 April 2009

• Fix a remote crash in fragmentation code

• Phase2 message identities are phase1 specific (Vista compatibility)

• Autogenerate ChangeLog from cvs metadata

• Fix mode config pool resizing

• NAT-T fixes related to purging of IPsec SA:s and retransmission

• Remove phase1 handler immediately if first exchange is bad

• A bunch of memory leak and possible memory corruptions (triggerable
            by bad configuration or startup parameters)

Seems like an update that is worth upgrading to given how many crash fixes there are in it.

[kapara]

But this is not likely to be applied to 1.2.2….... :'(  Or at least in 1.2.3 unless it is already there.  Just concerned about stability.

[drees]

@kapara:

But this is not likely to be applied to 1.2.2….... :'(  Or at least in 1.2.3 unless it is already there.  Just concerned about stability.

The devs have to consider what is worse:

1. Potential instability due to a new version of ipsec-tools or even an increase in stability due to bugs being fixed.
2. Shipping with a remote DoS attack vulnerability that has been known for 3 weeks now.

[jimp]

I am testing a build of 1.2.3-RC with ipsec-tools 0.7.2 and it may be my slightly weird test environment, but it didn't fix the issue so far.

That said, if I switch both ends of the IPSec tunnel to Aggressive Mode instead of Main Mode, then DPD seems to want to work, but doesn't actually get all the way.

May 14 10:17:55 pfsense-123test racoon: INFO: IPsec-SA request for x.x.x.49 queued due to no phase1 found.
May 14 10:17:55 pfsense-123test racoon: INFO: initiate new phase 1 negotiation: x.x.x.40[500]<=>x.x.x.49[500]
May 14 10:17:55 pfsense-123test racoon: INFO: begin Aggressive mode.
May 14 10:17:55 pfsense-123test racoon: INFO: received Vendor ID: CISCO-UNITY
May 14 10:17:55 pfsense-123test racoon: INFO: received Vendor ID: draft-ietf-ipsra-isakmp-xauth-06.txt
May 14 10:17:55 pfsense-123test racoon: INFO: received Vendor ID: DPD
May 14 10:17:55 pfsense-123test racoon: NOTIFY: couldn't find the proper pskey, try to get one by the peer's address.
May 14 10:17:55 pfsense-123test racoon: INFO: ISAKMP-SA established x.x.x.40[500]-x.x.x.49[500] spi:5570f421d746e391:6a94f32073b1ed3f
May 14 10:17:56 pfsense-123test racoon: INFO: initiate new phase 2 negotiation: x.x.x.40[500]<=>x.x.x.49[500]
May 14 10:17:56 pfsense-123test racoon: WARNING: ignore RESPONDER-LIFETIME notification.
May 14 10:17:56 pfsense-123test racoon: INFO: IPsec-SA established: ESP x.x.x.49[0]->x.x.x.40[0] spi=165272301(0x9d9daed)
May 14 10:17:56 pfsense-123test racoon: INFO: IPsec-SA established: ESP x.x.x.40[500]->x.x.x.49[500] spi=463118085(0x1b9a9f05)
[Power off Cisco VPN Concentrator]
May 14 10:19:10 pfsense-123test racoon: INFO: DPD: remote (ISAKMP-SA spi=5570f421d746e391:6a94f32073b1ed3f) seems to be dead.
May 14 10:19:11 pfsense-123test racoon: INFO: ISAKMP-SA deleted x.x.x.40[500]-x.x.x.49[500] spi:5570f421d746e391:6a94f32073b1ed3f

The log message is all well and good except it didn't actually delete the SAs. They're still there.

I'm making a new build right now to see if things behave any differently. Before that, I'm going to go back to a stock 1.2.3 snapshot and see if Aggressive mode behaves the same way.

[kapara]

All is now working!  I removed the Concentrator from the DMZ of my local pfSense and connected it directly to a public IP.  I noticed in the firewall logs that my firewall was blocking port 500 traffic and all other traffic which originated from the remote sites to my local site.  Odd since I created a rule on my DMZ allowing all traffic to pass to the public interface of my concentrator.

Lan 10.20.30.1
DMZ 10.20.20.1

Concentrator Private: 10.20.30.2
Concentrator Public: 10.20.20.2

I was seeing my customers IP's being blocked:

10.0.0.0/24
192.168.127.0/24
172.20.30.0/16

These were being blocked both on the LAN interface and on the DMZ.  I will post some of the logs.  I just need to reconfigure to internal again rather than direct connect to public IP on Concentrator Public interface.

[jimp]

So your tunnel reestablishes OK now after a power cycle?

That is strange, since my concentrator is already on a public IP and has no filtering in front of it. Its public is on the same switch as my pfSense test box.

And yet if I power cycle the concentrator, the tunnel never comes back up.

Are you sure nothing else changed in all that?

[kapara]

I did modify the DPD setting in the pfSense 1.2.2 by modifying the file.  I think DPD was enabled for phase 1 or phase 2 and I enabled it for the other one in the conf file.  If I can remember which file I will post the changes I made.

[jimp]

Ok, that would help a lot.

It should be /var/etc/racoon.conf

If I can see how you changed it, I can probably get that into the code to see if it fixes for everyone.

[kapara]

Look for the dpd_delay.  On one of them it is commented out.  File is:  /etc/inc/vpn.inc

See post: http://forum.pfsense.org/index.php/topic,10371.0.html

From Pesh:

I don't know if everyone else has encountered this, but I recently had a problem where if one of my pfSense firewalls was restarted for whatever reason, the other pfSenses on the other ends of the VPN tunnels wouldn't recognise this. They would keep the old SA up and not negotiate any new ones, causing a failure to pass any traffic over the VPN. The only fix was to manually delete the entries from the SAD on these other firewalls so it would make a fresh tunnel again.

After reading around a bit, I saw an option for the racoon.conf that would turn on Dead Peer Detection, and figured I'd give that a try. In /etc/inc/vpn.inc, after each line saying proposal_check obey;, I added a line dpd_delay 20;. Then restarted racoon on each firewall, restarted one of the firewalls on its own and found that it renegotiated the tunnels straight away!

Anyway just a suggestion, I think this would be a useful option to add to pfSense.

/*
	vpn.inc
	Copyright (C) 2004-2006 Scott Ullrich
	All rights reserved.

	originally part of m0n0wall (http://m0n0.ch/wall)
	Copyright (C) 2003-2004 Manuel Kasper <mk@neon1.net>.
	All rights reserved.

	Redistribution and use in source and binary forms, with or without
	modification, are permitted provided that the following conditions are met:

	1\. Redistributions of source code must retain the above copyright notice,
	   this list of conditions and the following disclaimer.

	2\. Redistributions in binary form must reproduce the above copyright
	   notice, this list of conditions and the following disclaimer in the
	   documentation and/or other materials provided with the distribution.

	THIS SOFTWARE IS PROVIDED ``AS IS'' AND ANY EXPRESS OR IMPLIED WARRANTIES,
	INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY
	AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
	AUTHOR BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY,
	OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF
	SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS
	INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN
	CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE)
	ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
	POSSIBILITY OF SUCH DAMAGE.
*/

/* include all configuration functions */
require_once("functions.inc");

/* master setup for vpn (mpd) */
function vpn_setup() {
	/* start pptpd */
	vpn_pptpd_configure();

	/* start pppoe server */
	vpn_pppoe_configure();
}

function vpn_ipsec_failover_configure() {
	global $config, $g;

	$sasyncd_text = "";

	if($config['installedpackages']['sasyncd']['config'] <> "")
		foreach($config['installedpackages']['sasyncd']['config'] as $sasyncd) {
			$enabled = isset($sasyncd['enable']);
			if(!$enabled)
				return;
			if($sasyncd['peerip'] <> "")
				$sasyncd_text .= "peer {$sasyncd['peerip']}\n";
			if($sasyncd['interface'])
				$sasyncd_text .= "carp interface {$sasyncd['interface']}\n";
			if($sasyncd['sharedkey'] <> "")
				$sasyncd_text .= "sharedkey {$sasyncd['sharedkey']}\n";
			if($sasyncd['mode'] <> "")
				$sasyncd_text .= "mode {$sasyncd['mode']}\n";
			if($sasyncd['listenon'] <> "")
				$sasyncd_text .= "listen on {$sasyncd['listenon']}\n";
			if($sasyncd['flushmodesync'] <> "")
				$sasyncd_text .= "flushmode sync {$sasyncd['flushmodesync']}\n";
		}

	$fd = fopen("{$g['varetc_path']}/sasyncd.conf", "w");
	fwrite($fd, $sasyncd_text);
	fclose($fd);
	chmod("{$g['varetc_path']}/sasyncd.conf", 0600);

	mwexec("killall sasyncd", true);

	/* launch sasyncd, oh wise one */
	/* mwexec_bg("/usr/local/sbin/sasyncd -d -v -v -v"); */
}

function find_last_gif_device() {
	 	$regs = "";
        $last_gif_found = -1;
        if (!($fp = popen("/sbin/ifconfig -l", "r"))) return -1;
        $ifconfig_data = fread($fp, 4096);
        pclose($fp);
        $ifconfig_array = split(" ", $ifconfig_data);
        foreach ($ifconfig_array as $ifconfig) {
                ereg("gif(.)", $ifconfig, $regs);
                if($regs[0]) {
                        if($regs[0] > $last_gif_found)
                                $last_gif_found = $regs[1];
                }
        }
        return $last_gif_found;
}

function vpn_ipsec_configure($ipchg = false) {
	global $config, $g, $sa, $sn;

	mwexec("/sbin/ifconfig enc0 create", true);
	mwexec("/sbin/ifconfig enc0 up", true);

	/* get the automatic /etc/ping_hosts.sh ready */
	unlink_if_exists("/var/db/ipsecpinghosts");
	touch("/var/db/ipsecpinghosts");

	if($g['booting'] == true) {
		/* determine if we should load the via padlock module */
		$dmesg_boot = `cat /var/log/dmesg.boot | grep CPU`;
		if(stristr($dmesg_boot, "ACE") == true) {
			//echo "Enabling [VIA Padlock] ...";
			//mwexec("/sbin/kldload padlock");
			//mwexec("/sbin/sysctl net.inet.ipsec.crypto_support=1");
			//mwexec("/usr/local/sbin/setkey -F");
			//mwexec("/usr/local/sbin/setkey -FP");
			//echo " done.\n";
		}
	}

	if(isset($config['ipsec']['preferredoldsa'])) {
		mwexec("/sbin/sysctl net.key.preferred_oldsa=0");
	} else {
		mwexec("/sbin/sysctl -w net.key.preferred_oldsa=-30");
	}

	$number_of_gifs = find_last_gif_device();
	for($x=0; $x<$number_of_gifs; $x++) {
		mwexec("/sbin/ifconfig gif" . $x . " delete");
	}

	$curwanip = get_current_wan_address();

	$syscfg = $config['system'];
	$ipseccfg = $config['ipsec'];
	$lancfg = $config['interfaces']['lan'];
	$lanip = $lancfg['ipaddr'];
	$lansa = gen_subnet($lancfg['ipaddr'], $lancfg['subnet']);
	$lansn = $lancfg['subnet'];

	if (!isset($ipseccfg['enable'])) {
		mwexec("/sbin/ifconfig enc0 down");
		mwexec("/sbin/ifconfig enc0 destroy");

		/* kill racoon */
		mwexec("/usr/bin/killall racoon", true);

		/* wait for process to die */
		sleep(2);

		/* send a SIGKILL to be sure */
		sigkillbypid("{$g['varrun_path']}/racoon.pid", "KILL");

		/* flush SPD and SAD */
		mwexec("/usr/local/sbin/setkey -FP");
		mwexec("/usr/local/sbin/setkey -F");

		return true;
	}

	if ($g['booting']) {
		echo "Configuring IPsec VPN... ";
	}

	if (isset($ipseccfg['enable'])) {

		/* fastforwarding is not compatible with ipsec tunnels */
		system("/sbin/sysctl net.inet.ip.fastforwarding=0 >/dev/null 2>&1");

		if (!$curwanip) {
			/* IP address not configured yet, exit */
			if ($g['booting'])
				echo "done\n";
			return 0;
		}

		/* this loads a route table which is used to determine if a route needs to be removed. */
		exec("/usr/bin/netstat -rn", $route_arr, $retval);
		$route_str = implode("\n", $route_arr);

		if ((is_array($ipseccfg['tunnel']) && count($ipseccfg['tunnel'])) ||
				isset($ipseccfg['mobileclients']['enable'])) {

			if (is_array($ipseccfg['tunnel']) && count($ipseccfg['tunnel'])) {

				/* generate spd.conf */
				$fd = fopen("{$g['varetc_path']}/spd.conf", "w");
				if (!$fd) {
					printf("Error: cannot open spd.conf in vpn_ipsec_configure().\n");
					return 1;
				}

				$spdconf = "";

				$spdconf .= "spdadd {$lansa}/{$lansn} {$lanip}/32 any -P in none;\n";
				$spdconf .= "spdadd {$lanip}/32 {$lansa}/{$lansn} any -P out none;\n";

				foreach ($ipseccfg['tunnel'] as $tunnel) {

					if (isset($tunnel['disabled']))
						continue;

					$ep = vpn_endpoint_determine($tunnel, $curwanip);
					if (!$ep) {
						log_error("Could not deterimine VPN endpoint for {$tunnel['descr']}");
						continue;	
					}

					vpn_localnet_determine($tunnel['local-subnet'], $sa, $sn);

					if(is_domain($tunnel['remote-gateway'])) {
						$tmp = gethostbyname($tunnel['remote-gateway']);
						if($tmp)
							$tunnel['remote-gateway'] = $tmp;
					}

					/* add entry to host pinger */
					if ($tunnel['pinghost']) {
						$pfd = fopen("/var/db/ipsecpinghosts", "a");
						$iflist = array("lan" => "lan", "wan" => "wan");
			          	for ($i = 1; isset($config['interfaces']['opt' . $i]); $i++)
			          		$iflist['opt' . $i] = "opt{$i}";
			            foreach ($iflist as $ifent => $ifname) {
			            	$interface_ip = find_interface_ip($config['interfaces'][$ifname]['if']);
			            	if (ip_in_subnet($interface_ip, $sa . "/" . $sn))
			                	$srcip = find_interface_ip($config['interfaces'][$ifname]['if']);
			            }
						$dstip = $tunnel['pinghost'];
						fwrite($pfd, "$srcip|$dstip|3\n");
						fclose($pfd);
					}
					if(isset($tunnel['creategif'])) {
						$number_of_gifs = find_last_gif_device();
						$number_of_gifs++;
						$curwanip = get_current_wan_address();

						mwexec("/sbin/ifconfig gif" . $number_of_gifs . " tunnel" . $curwanip . " " . $tunnel['remote-gateway']);
						mwexec("/sbin/ifconfig gif" . $number_of_gifs . " {$lansa}/{$lansn} {$lanip}/32");
					}

					$spdconf .= "spdadd {$sa}/{$sn} " .
						"{$tunnel['remote-subnet']} any -P out ipsec " .
						"{$tunnel['p2']['protocol']}/tunnel/{$ep}-" .
						"{$tunnel['remote-gateway']}/unique;\n";

					$spdconf .= "spdadd {$tunnel['remote-subnet']} " .
						"{$sa}/{$sn} any -P in ipsec " .
						"{$tunnel['p2']['protocol']}/tunnel/{$tunnel['remote-gateway']}-" .
						"{$ep}/unique;\n";

					/* static route needed? */
					if(preg_match("/^carp/i", $tunnel['interface'])) {
						$parentinterface = link_carp_interface_to_parent($tunnel['interface']);
					} else {
						$parentinterface = $tunnel['interface'];
					}
					if($parentinterface <> "wan") {
						/* add endpoint routes to correct gateway on interface */
						if(interface_has_gateway($parentinterface)) {
							$gatewayip = get_interface_gateway("$parentinterface");
							$interfaceip = $config['interfaces'][$parentinterface]['ipaddr'];
							$subnet_bits = $config['interfaces'][$parentinterface]['subnet'];
							$subnet_ip = gen_subnet("{$interfaceip}", "{$subnet_bits}");
							/* if the remote gateway is in the local subnet, then don't add a route */
							if(! ip_in_subnet($tunnel['remote-gateway'], "{$subnet_ip}/{$subnet_bits}")) {
								if(is_ipaddr($gatewayip)) {
									log_error("IPSEC interface is not WAN but {$tunnel['interface']}, adding static route for VPN endpoint {$tunnel['remote-gateway']} via {$gatewayip}");
									mwexec("/sbin/route delete -host {$tunnel['remote-gateway']}");
                                                                        mwexec("/sbin/route add -host {$tunnel['remote-gateway']} {$gatewayip}");
								}
							}
						}
					} else {
						if(stristr($route_str, "/{$tunnel['remote-gateway']}/")) {
							mwexec("/sbin/route delete -host {$tunnel['remote-gateway']}");
						}
					}
				}

				fwrite($fd, $spdconf);
				fclose($fd);
			}

			/* generate racoon.conf */
			$fd = fopen("{$g['varetc_path']}/racoon.conf", "w");
			if (!$fd) {
				printf("Error: cannot open racoon.conf in vpn_ipsec_configure().\n");
				return 1;
			}

			$racoonconf = "";

			$racoonconf .= "path pre_shared_key \"{$g['varetc_path']}/psk.txt\";\n\n";
			$racoonconf .= "path certificate  \"{$g['varetc_path']}\";\n\n";

			/* generate CA certificates files */
			$cacertnum = 0;
			if (is_array($ipseccfg['cacert']) && count($ipseccfg['cacert']))
				foreach ($ipseccfg['cacert'] as $cacert) {
					++$cacertnum;
					if (isset($cacert['cert'])) {
						$cert = base64_decode($cacert['cert']);
						$x509cert = openssl_x509_parse(openssl_x509_read($cert));
						if(is_array($x509cert) && isset($x509cert['hash'])) {
							$fd1 = fopen("{$g['varetc_path']}/{$x509cert['hash']}.0", "w");
							if (!$fd1) {
								printf("Error: cannot open {$x509cert['hash']}.0 in vpn.\n");
								return 1;
							}
							chmod("{$g['varetc_path']}/{$x509cert['hash']}.0", 0600);
							fwrite($fd1, $cert);
							fclose($fd1);
						}
					}
				}

			$tunnelnumber = 0;
			if (is_array($ipseccfg['tunnel']) && count($ipseccfg['tunnel']))
				foreach ($ipseccfg['tunnel'] as $tunnel) {

				++$tunnelnumber;

				if (isset($tunnel['disabled']))
					continue;

				$ep = vpn_endpoint_determine($tunnel, $curwanip);
				if (!$ep)
					continue;

				vpn_localnet_determine($tunnel['local-subnet'], $sa, $sn);

				if (isset($tunnel['p1']['myident']['myaddress'])) {
					$myidentt = "address";
					$myident = $ep;
				} else if (isset($tunnel['p1']['myident']['address'])) {
					$myidentt = "address";
					$myident = $tunnel['p1']['myident']['address'];
				} else if (isset($tunnel['p1']['myident']['fqdn'])) {
					$myidentt = "fqdn";
					$myident = $tunnel['p1']['myident']['fqdn'];
				} else if (isset($tunnel['p1']['myident']['ufqdn'])) {
					$myidentt = "user_fqdn";
					$myident = $tunnel['p1']['myident']['ufqdn'];
 				} else if (isset($tunnel['p1']['myident']['dyn_dns'])) {
					$myidentt = "dyn_dns";
					$myident = gethostbyname($tunnel['p1']['myident']['dyn_dns']);
 				}

				if (!($myidentt == "asn1dn" && $myident == "")) {
					$myident = " \"".$myident."\"";
				}

				$nattline = '';
				if (isset($tunnel['natt'])) {
					$nattline = "nat_traversal on;";
				}

				if (isset($tunnel['p1']['authentication_method'])) {
					$authmethod = $tunnel['p1']['authentication_method'];
				} else {$authmethod = 'pre_shared_key';}

				$certline = '';

				if ($authmethod == 'rsasig') {
					if ($tunnel['p1']['cert'] && $tunnel['p1']['private-key']) {
						$cert = base64_decode($tunnel['p1']['cert']);
						$private_key = base64_decode($tunnel['p1']['private-key']);
					} else {
						/* null certificate/key */
						$cert = '';
						$private_key = '';
					}

					if ($tunnel['p1']['peercert'])
						$peercert = base64_decode($tunnel['p1']['peercert']);
					else
						$peercert = '';

					$fd1 = fopen("{$g['varetc_path']}/server{$tunnelnumber}-signed.pem", "w");
					if (!$fd1) {
						printf("Error: cannot open server{$tunnelnumber}-signed.pem in vpn.\n");
						return 1;
					}
					chmod("{$g['varetc_path']}/server{$tunnelnumber}-signed.pem", 0600);
					fwrite($fd1, $cert);
					fclose($fd1);

					$fd1 = fopen("{$g['varetc_path']}/server{$tunnelnumber}-key.pem", "w");
					if (!$fd1) {
						printf("Error: cannot open server{$tunnelnumber}-key.pem in vpn.\n");
						return 1;
					}
					chmod("{$g['varetc_path']}/server{$tunnelnumber}-key.pem", 0600);
					fwrite($fd1, $private_key);
					fclose($fd1);

					$certline = "certificate_type x509 \"server{$tunnelnumber}-signed.pem\" \"server{$tunnelnumber}-key.pem\";";

					if ($peercert!=''){
						$fd1 = fopen("{$g['varetc_path']}/peer{$tunnelnumber}-signed.pem", "w");
						if (!$fd1) {
							printf("Error: cannot open server{$tunnelnumber}-signed.pem in vpn.\n");
							return 1;
						}
						chmod("{$g['varetc_path']}/peer{$tunnelnumber}-signed.pem", 0600);
						fwrite($fd1, $peercert);
						fclose($fd1);
						$certline .= << <eod<br>peers_certfile "peer{$tunnelnumber}-signed.pem";
EOD;
					}
				}
				$racoonconf .= <<<eod<br>remote {$tunnel['remote-gateway']} \{
	exchange_mode {$tunnel['p1']['mode']};
	my_identifier {$myidentt}{$myident};
	{$certline}
	peers_identifier address {$tunnel['remote-gateway']};
	initial_contact on;
	#dpd_delay 120;                   # DPD poll every 120 seconds
	ike_frag on;
	support_proxy on;
	proposal_check obey;
	dpd_delay 20;

	proposal \{
		encryption_algorithm {$tunnel['p1']['encryption-algorithm']};
		hash_algorithm {$tunnel['p1']['hash-algorithm']};
		authentication_method {$authmethod};
		dh_group {$tunnel['p1']['dhgroup']};

EOD;
				if ($tunnel['p1']['lifetime'])
					$racoonconf .= "		lifetime time {$tunnel['p1']['lifetime']} secs;\n";

				$racoonconf .= "	}\n";

				if ($tunnel['p1']['lifetime'])
					$racoonconf .= "	lifetime time {$tunnel['p1']['lifetime']} secs;\n";

				$racoonconf .= "}\n\n";

				$p2ealgos = join(",", $tunnel['p2']['encryption-algorithm-option']);
				$p2halgos = join(",", $tunnel['p2']['hash-algorithm-option']);

				$racoonconf .= <<<eod<br>sainfo address {$sa}/{$sn} any address {$tunnel['remote-subnet']} any \{
	encryption_algorithm {$p2ealgos};
	authentication_algorithm {$p2halgos};
	compression_algorithm deflate;

EOD;

				if ($tunnel['p2']['pfsgroup'])
					$racoonconf .= "	pfs_group {$tunnel['p2']['pfsgroup']};\n";

				if ($tunnel['p2']['lifetime'])
					$racoonconf .= "	lifetime time {$tunnel['p2']['lifetime']} secs;\n";

				$racoonconf .= "}\n\n";
			}

			/* mobile clients? */
			if (isset($ipseccfg['mobileclients']['enable'])) {

				$tunnel = $ipseccfg['mobileclients'];

				if (isset($tunnel['p1']['myident']['myaddress'])) {
					$myidentt = "address ";
					$myident = $curwanip;
				} else if (isset($tunnel['p1']['myident']['address'])) {
					$myidentt = "address ";
					$myident = $tunnel['p1']['myident']['address'];
				} else if (isset($tunnel['p1']['myident']['fqdn'])) {
					$myidentt = "fqdn ";
					$myident = $tunnel['p1']['myident']['fqdn'];
				} else if (isset($tunnel['p1']['myident']['ufqdn'])) {
					$myidentt = "user_fqdn ";
					$myident = $tunnel['p1']['myident']['ufqdn'];
 				}

				if (isset($tunnel['p1']['authentication_method'])) {
					$authmethod = $tunnel['p1']['authentication_method'];
				} else {$authmethod = 'pre_shared_key';}

				$certline = '';
				if ($authmethod == 'rsasig') {
					if ($tunnel['p1']['cert'] && $tunnel['p1']['private-key']) {
						$cert = base64_decode($tunnel['p1']['cert']);
						$private_key = base64_decode($tunnel['p1']['private-key']);
					} else {
						/* null certificate/key */
						$cert = '';
						$private_key = '';
					}

					if ($tunnel['p1']['peercert'])
						$peercert = base64_decode($tunnel['p1']['peercert']);
					else
						$peercert = '';

					$fd1 = fopen("{$g['varetc_path']}/server-mobile{$tunnelnumber}-signed.pem", "w");
					if (!$fd1) {
						printf("Error: cannot open server-mobile{$tunnelnumber}-signed.pem in vpn.\n");
						return 1;
					}
					chmod("{$g['varetc_path']}/server-mobile{$tunnelnumber}-signed.pem", 0600);
					fwrite($fd1, $cert);
					fclose($fd1);

					$fd1 = fopen("{$g['varetc_path']}/server-mobile{$tunnelnumber}-key.pem", "w");
					if (!$fd1) {
						printf("Error: cannot open server-mobile{$tunnelnumber}-key.pem in vpn.\n");
						return 1;
					}
					chmod("{$g['varetc_path']}/server-mobile{$tunnelnumber}-key.pem", 0600);
					fwrite($fd1, $private_key);
					fclose($fd1);

					$certline = "certificate_type x509 \"server-mobile{$tunnelnumber}-signed.pem\" \"server-mobile{$tunnelnumber}-key.pem\";";
				}
				$racoonconf .= <<<eod<br>remote anonymous \{
	exchange_mode {$tunnel['p1']['mode']};
	my_identifier {$myidentt}"{$myident}";	
	{$nattline}
	{$certline}
	initial_contact on;
	dpd_delay 120;                   # DPD poll every 120 seconds
	ike_frag on;
	passive on;
	generate_policy on;
	support_proxy on;
	proposal_check obey;
	dpd_delay 20;

	proposal \{
		encryption_algorithm {$tunnel['p1']['encryption-algorithm']};
		hash_algorithm {$tunnel['p1']['hash-algorithm']};
		authentication_method {$authmethod};
		dh_group {$tunnel['p1']['dhgroup']};

EOD;
				if ($tunnel['p1']['lifetime'])
					$racoonconf .= "		lifetime time {$tunnel['p1']['lifetime']} secs;\n";

				$racoonconf .= "	}\n";

				if ($tunnel['p1']['lifetime'])
					$racoonconf .= "	lifetime time {$tunnel['p1']['lifetime']} secs;\n";

				$racoonconf .= "}\n\n";

				$p2ealgos = join(",", $tunnel['p2']['encryption-algorithm-option']);
				$p2halgos = join(",", $tunnel['p2']['hash-algorithm-option']);

				$racoonconf .= <<<eod<br>sainfo anonymous \{
	encryption_algorithm {$p2ealgos};
	authentication_algorithm {$p2halgos};
	compression_algorithm deflate;

EOD;

				if ($tunnel['p2']['pfsgroup'])
					$racoonconf .= "	pfs_group {$tunnel['p2']['pfsgroup']};\n";

				if ($tunnel['p2']['lifetime'])
					$racoonconf .= "	lifetime time {$tunnel['p2']['lifetime']} secs;\n";

				$racoonconf .= "}\n\n";
			}

			fwrite($fd, $racoonconf);
			fclose($fd);

			/* generate psk.txt */
			$fd = fopen("{$g['varetc_path']}/psk.txt", "w");
			if (!$fd) {
				printf("Error: cannot open psk.txt in vpn_ipsec_configure().\n");
				return 1;
			}

			$pskconf = "";

			if (is_array($ipseccfg['tunnel'])) {
				foreach ($ipseccfg['tunnel'] as $tunnel) {
					if (isset($tunnel['disabled']))
						continue;
					$pskconf .= "{$tunnel['remote-gateway']}	 {$tunnel['p1']['pre-shared-key']}\n";
				}
			}

			/* add PSKs for mobile clients */
			if (is_array($ipseccfg['mobilekey'])) {
				foreach ($ipseccfg['mobilekey'] as $key) {
					$pskconf .= "{$key['ident']}	{$key['pre-shared-key']}\n";
				}
			}

			fwrite($fd, $pskconf);
			fclose($fd);
			chmod("{$g['varetc_path']}/psk.txt", 0600);

			if(is_process_running("racoon")) {
				/* flush SPD entries */
				mwexec("/usr/local/sbin/setkey -FP");
				sleep("0.1");
				mwexec("/usr/local/sbin/setkey -F");
				/* load SPD */
				sleep("0.1");
				mwexec("/usr/local/sbin/setkey -f {$g['varetc_path']}/spd.conf");
				/* We are already online, reload */
				sleep("0.1");
				mwexec("/usr/bin/killall -HUP racoon", true);
			} else {
				/* flush SA + SPD entries */
				mwexec("/usr/local/sbin/setkey -FP");
				sleep("0.1");
				mwexec("/usr/local/sbin/setkey -F");
				sleep("0.1");
				/* start racoon */
				mwexec("/usr/local/sbin/racoon -f {$g['varetc_path']}/racoon.conf");
				sleep("0.1");
				/* load SPD */
				mwexec("/usr/local/sbin/setkey -f {$g['varetc_path']}/spd.conf");
				/* We are already online, reload */
				sleep("0.1");
				mwexec("/usr/bin/killall -HUP racoon", true);
			}
		}
	}

	vpn_ipsec_failover_configure();

	if (!$g['booting']) {
		/* reload the filter */
		touch("{$g["tmp_path"]}/filter_dirty");
	}

	if ($g['booting'])
		echo "done\n";

	return 0;
}

function vpn_pptpd_configure() {
	global $config, $g;

	$syscfg = $config['system'];
	$pptpdcfg = $config['pptpd'];

	if ($g['booting']) {
		if (!$pptpdcfg['mode'] || ($pptpdcfg['mode'] == "off"))
			return 0;

		echo "Configuring PPTP VPN service... ";
	} else {
		/* kill mpd */
		killbypid("{$g['varrun_path']}/mpd-vpn.pid");

		/* wait for process to die */
		sleep(3);

		if(is_process_running("mpd -b")) {
			killbypid("{$g['varrun_path']}/mpd-vpn.pid");
			log_error("Could not kill mpd within 3 seconds.   Trying again.");
		}

		/* remove mpd.conf, if it exists */
		unlink_if_exists("{$g['varetc_path']}/mpd-vpn/mpd.conf");
		unlink_if_exists("{$g['varetc_path']}/mpd-vpn/mpd.links");
		unlink_if_exists("{$g['varetc_path']}/mpd-vpn/mpd.secret");
	}

	/* make sure mpd-vpn directory exists */
	if (!file_exists("{$g['varetc_path']}/mpd-vpn"))
		mkdir("{$g['varetc_path']}/mpd-vpn");

	switch ($pptpdcfg['mode']) {

		case 'server':

			/* write mpd.conf */
			$fd = fopen("{$g['varetc_path']}/mpd-vpn/mpd.conf", "w");
			if (!$fd) {
				printf("Error: cannot open mpd.conf in vpn_pptpd_configure().\n");
				return 1;
			}

			$mpdconf = <<<eod<br>pptpd:

EOD;

			for ($i = 0; $i < $g['n_pptp_units']; $i++) {
				$mpdconf .= "	load pt{$i}\n";
			}

			for ($i = 0; $i < $g['n_pptp_units']; $i++) {

				$clientip = long2ip(ip2long($pptpdcfg['remoteip']) + $i);
				$ngif = "ng" . ($i+1);

				$mpdconf .= << <eod<br>pt{$i}:
	new -i {$ngif} pt{$i} pt{$i}
	set ipcp ranges {$pptpdcfg['localip']}/32 {$clientip}/32
	load pts

EOD;
			}

			$mpdconf .= << <eod<br>pts:
	set iface disable on-demand
	set iface enable proxy-arp
	set iface enable tcpmssfix
	set iface idle 1800
	set iface up-script /usr/local/sbin/vpn-linkup
	set iface down-script /usr/local/sbin/vpn-linkdown
	set bundle enable multilink
	set bundle enable crypt-reqd
	set link yes acfcomp protocomp
	set link no pap chap
	set link enable chap-msv2
	set link mtu 1460
	set link keep-alive 10 60
	set ipcp yes vjcomp
	set bundle enable compression
	set ccp yes mppc
	set ccp yes mpp-e128
	set ccp yes mpp-stateless

EOD;

			if (!isset($pptpdcfg['req128'])) {
				$mpdconf .= << <eod<br>set ccp yes mpp-e40
	set ccp yes mpp-e56

EOD;
			}
			if  (isset($pptpdcfg["wins"]))
				$mpdconf  .=  "	set ipcp nbns {$pptpdcfg['wins']}\n";
			if (is_array($pptpdcfg['dnsserver']) && ($pptpdcfg['dnsserver'][0])) {
				$mpdconf .= "	set ipcp dns " . join(" ", $pptpdcfg['dnsserver']) . "\n";
			} else if (isset($config['dnsmasq']['enable'])) {
				$mpdconf .= "	set ipcp dns " . $config['interfaces']['lan']['ipaddr'];
				if ($syscfg['dnsserver'][0])
					$mpdconf .= " " . $syscfg['dnsserver'][0];
				$mpdconf .= "\n";
			} else if (is_array($syscfg['dnsserver']) && ($syscfg['dnsserver'][0])) {
				$mpdconf .= "	set ipcp dns " . join(" ", $syscfg['dnsserver']) . "\n";
			}

			if (isset($pptpdcfg['radius']['enable'])) {
				$mpdconf .= << <eod<br>set radius server {$pptpdcfg['radius']['server']} "{$pptpdcfg['radius']['secret']}"
	set radius retries 3
	set radius timeout 10
	set bundle enable radius-auth
	set bundle disable radius-fallback

EOD;

				if (isset($pptpdcfg['radius']['accounting'])) {
					$mpdconf .= << <eod<br>set bundle enable radius-acct

EOD;
				}
			}

			fwrite($fd, $mpdconf);
			fclose($fd);

			/* write mpd.links */
			$fd = fopen("{$g['varetc_path']}/mpd-vpn/mpd.links", "w");
			if (!$fd) {
				printf("Error: cannot open mpd.links in vpn_pptpd_configure().\n");
				return 1;
			}

			$mpdlinks = "";

			for ($i = 0; $i < $g['n_pptp_units']; $i++) {
				$mpdlinks .= << <eod<br>pt{$i}:
	set link type pptp
	set pptp enable incoming
	set pptp disable originate
	set pptp disable windowing
	set pptp self 127.0.0.1

EOD;
			}

			fwrite($fd, $mpdlinks);
			fclose($fd);

			/* write mpd.secret */
			$fd = fopen("{$g['varetc_path']}/mpd-vpn/mpd.secret", "w");
			if (!$fd) {
				printf("Error: cannot open mpd.secret in vpn_pptpd_configure().\n");
				return 1;
			}

			$mpdsecret = "";

			if (is_array($pptpdcfg['user'])) {
				foreach ($pptpdcfg['user'] as $user)
					$mpdsecret .= "{$user['name']} \"{$user['password']}\" {$user['ip']}\n";
			}

			fwrite($fd, $mpdsecret);
			fclose($fd);
			chmod("{$g['varetc_path']}/mpd-vpn/mpd.secret", 0600);

			/* fire up mpd */
			mwexec("/usr/local/sbin/mpd -b -d {$g['varetc_path']}/mpd-vpn -p {$g['varrun_path']}/mpd-vpn.pid pptpd");

			break;

		case 'redir':
			break;
	}

	if (!$g['booting']) {
		/* reload the filter */
		filter_configure();
	}

	if ($g['booting'])
		echo "done\n";

	return 0;
}

function vpn_localnet_determine($adr, &$sa, &$sn) {
	global $config, $g;

	if (isset($adr)) {
		if ($adr['network']) {
			switch ($adr['network']) {
				case 'lan':
					$sn = $config['interfaces']['lan']['subnet'];
					$sa = gen_subnet($config['interfaces']['lan']['ipaddr'], $sn);
					break;
			}
		} else if ($adr['address']) {
			list($sa,$sn) = explode("/", $adr['address']);
			if (is_null($sn))
				$sn = 32;
		}
	} else {
		$sn = $config['interfaces']['lan']['subnet'];
		$sa = gen_subnet($config['interfaces']['lan']['ipaddr'], $sn);
	}
}

function vpn_endpoint_determine($tunnel, $curwanip) {
	global $g, $config;

	if(!$tunnel['interface']) {
		return null;
	}
	if(is_ipaddr($curwanip)) {
		if(preg_match("/^carp/i", $tunnel['interface'])) {
			$iface = $tunnel['interface'];
		} else {
			if($config['interfaces'][$tunnel['interface']]['ipaddr'] == "pppoe" OR 
				$config['interfaces'][$tunnel['interface']]['ipaddr'] == "pptp") {
				$iface = "ng0";
			} else {
				$iface = $config['interfaces'][$tunnel['interface']]['if'];
			}
		}
		$oc = $config['interfaces'][$tunnel['interface']];
		/* carp ips, etc */
		$ip = find_interface_ip($iface);
		if($ip)
			return $ip;

		if (isset($oc['enable']) && $oc['if']) {
			return $oc['ipaddr'];
		}
	}
	return null;
}

function vpn_pppoe_configure() {
	global $config, $g;

	$syscfg = $config['system'];
	$pppoecfg = $config['pppoe'];

	/* create directory if it does not exist */
	if(!is_dir("{$g['varetc_path']}/mpd-vpn"))
		mkdir("{$g['varetc_path']}/mpd-vpn");

	if ($g['booting']) {
		if (!$pppoecfg['mode'] || ($pppoecfg['mode'] == "off"))
			return 0;

		echo "Configuring PPPoE VPN service... ";
	}

	/* make sure mpd-vpn directory exists */
	if (!file_exists("{$g['varetc_path']}/mpd-vpn"))
		mkdir("{$g['varetc_path']}/mpd-vpn");

	switch ($pppoecfg['mode']) {

		case 'server':

			$pppoe_interface = filter_translate_type_to_real_interface($pppoecfg['interface']);

			/* write mpd.conf */
			$fd = fopen("{$g['varetc_path']}/mpd-vpn/mpd.conf", "a");
			if (!$fd) {
				printf("Error: cannot open mpd.conf in vpn_pppoe_configure().\n");
				return 1;
			}
			$mpdconf = "\n\n";
			$mpdconf .= <<<eod<br>pppoe:

EOD;

			for ($i = 0; $i < $pppoecfg['n_pppoe_units']; $i++) {
				$mpdconf .= "	load pppoe{$i}\n";
			}

			for ($i = 0; $i < $pppoecfg['n_pppoe_units']; $i++) {

				$clientip = long2ip(ip2long($pppoecfg['remoteip']) + $i);
				$ngif = "ng" . ($i+1);

				if(isset($pppoecfg['radius']['radiusissueips']) && isset($pppoecfg['radius']['enable'])) {
					$isssue_ip_type = "set ipcp ranges {$pppoecfg['localip']}/32 0.0.0.0/0";
					$isssue_ip_type .="\n\tset ipcp yes radius-ip";
				} else {
					$isssue_ip_type = "set ipcp ranges {$pppoecfg['localip']}/32 {$clientip}/32";
				}

				$mpdconf .= << <eod<br>pppoe{$i}:
	new -i {$ngif} pppoe{$i} pppoe{$i}
	{$isssue_ip_type}
	load pppoe_standart

EOD;
			}

			$mpdconf .= << <eod<br>pppoe_standart:
	set link type pppoe
	set pppoe iface {$pppoe_interface}
	set pppoe service "*"
	set pppoe disable originate
	set pppoe enable incoming
	set bundle no multilink
	set bundle enable compression
	set bundle max-logins 1
	set iface idle 0
	set iface disable on-demand
	set iface disable proxy-arp
	set iface enable tcpmssfix
	set iface mtu 1500
	set link no pap chap
	set link enable chap
	set link keep-alive 60 180
	set ipcp yes vjcomp
	set ipcp no vjcomp
	set link max-redial -1
	set link mtu 1492
	set link mru 1492
	set ccp yes mpp-e40
	set ccp yes mpp-e128
	set ccp yes mpp-stateless
	set link latency 1
	#set ipcp dns 10.10.1.3
	#set bundle accept encryption

EOD;

			if (isset($config['dnsmasq']['enable'])) {
				$mpdconf .= "	set ipcp dns " . $config['interfaces']['lan']['ipaddr'];
				if ($syscfg['dnsserver'][0])
					$mpdconf .= " " . $syscfg['dnsserver'][0];
				$mpdconf .= "\n";
			} else if (is_array($syscfg['dnsserver']) && ($syscfg['dnsserver'][0])) {
				$mpdconf .= "	set ipcp dns " . join(" ", $syscfg['dnsserver']) . "\n";
			}

			if (isset($pppoecfg['radius']['enable'])) {
				$mpdconf .= << <eod<br>set radius server {$pppoecfg['radius']['server']} "{$pppoecfg['radius']['secret']}"
	set radius retries 3
	set radius timeout 10
	set bundle enable radius-auth
	set bundle disable radius-fallback

EOD;

				if (isset($pppoecfg['radius']['accounting'])) {
					$mpdconf .= << <eod<br>set bundle enable radius-acct
	set radius acct-update 300
EOD;
				}
			}

			fwrite($fd, $mpdconf);
			fclose($fd);

			/* write mpd.links */
			$fd = fopen("{$g['varetc_path']}/mpd-vpn/mpd.links", "a");
			if (!$fd) {
				printf("Error: cannot open mpd.links in vpn_pppoe_configure().\n");
				return 1;
			}

			$mpdlinks = "";

			for ($i = 0; $i < $pppoecfg['n_pppoe_units']; $i++) {
				$mpdlinks .= << <eod<br>pppoe:
	set link type pppoe
	set pppoe iface {$pppoe_interface}

EOD;
			}

			fwrite($fd, $mpdlinks);
			fclose($fd);

			/* write mpd.secret */
			$fd = fopen("{$g['varetc_path']}/mpd-vpn/mpd.secret", "a");
			if (!$fd) {
				printf("Error: cannot open mpd.secret in vpn_pppoe_configure().\n");
				return 1;
			}

			$mpdsecret = "\n\n";

			if (is_array($pppoecfg['user'])) {
				foreach ($pppoecfg['user'] as $user)
					$mpdsecret .= "{$user['name']} \"{$user['password']}\" {$user['ip']}\n";
			}

			fwrite($fd, $mpdsecret);
			fclose($fd);
			chmod("{$g['varetc_path']}/mpd-vpn/mpd.secret", 0600);

			/* fire up mpd */
			mwexec("/usr/local/sbin/mpd -b -d {$g['varetc_path']}/mpd-vpn -p {$g['varrun_path']}/mpd-vpn.pid pppoe");

			break;

		case 'redir':
			break;
	}

	touch("{$g["tmp_path"]}/filter_dirty");

	if ($g['booting'])
		echo "done\n";

	return 0;
}

/* Forcefully restart IPSEC
 * This is required for when dynamic interfaces reload
 * For all other occasions the normal vpn_ipsec_configure()
 * will gracefully reload the settings without restarting
 */
function vpn_ipsec_force_reload() {
	global $config;
	global $g;

	$ipseccfg = $config['ipsec'];

	/* kill any ipsec communications regardless when we are invoked */
	mwexec("/sbin/ifconfig enc0 down");

	/* kill racoon */
	mwexec("/usr/bin/killall racoon", true);

	/* wait for process to die */
	sleep(4);

	/* send a SIGKILL to be sure */
	sigkillbypid("{$g['varrun_path']}/racoon.pid", "KILL");

	/* wait for flushing to finish */
	sleep(1);

	/* if ipsec is enabled, start up again */
	if (isset($ipseccfg['enable'])) {
		log_error("Forcefully reloading IPSEC racoon daemon");
		vpn_ipsec_configure();
	}

}

?></eod<br></eod<br></eod<br></eod<br></eod<br></eod<br></eod<br></eod<br></eod<br></eod<br></eod<br></eod<br></eod<br></eod<br></eod<br></eod<br></eod<br></eod<br></mk@neon1.net> 

[jimp]

Ok, so if you look at the output of that, in your /var/etc/racoon.conf, where does dpd_delay show up there?

[kapara]

It is not the racoon.conf  It is the vpn.inc that needs to be edited