IPSec Tunnel dies but shows as up still

podilarius

Hey Guys,
NAT-T is still not working for me in 1.2.3 RC-1 built on Fri Apr 24 19:37:18 EDT 2009. Connects with no problem when NAT-T is disabled. Looks like a time out at phase 1. Anyone else seeing this behavior? Even better, does any one have this working with NAT-T?

kapara

Is anyone having a good experience with IPSEC lan to LAN with 1.2.3?

ankaerith

I updated to RC1 and all of my IPSec site-to-site tunnels die and can't recover without restarting IPSec. Please see my above post for more details.

I am not using NAT-T.

I tried enabling dead peer detection. It didn't help.

podilarius

I have only 1 site to site tunnel. I have to stop and restart ipsec after a reboot, but once I do this, it stays up until next reboot. I think that might have been due to another problem with my provider and a router port problem though that I have only had once. I will find out next time its down. (which might be a very long time)

Cheers guys.

ankaerith

I finally gave up on the 1.2.3 snapshots. I rolled back to 1.2.2 and my tunnels came back up and have been rock solid since. I made zero configuration changes. I simply pointed the console update URL to the 1.2.2 full upgrade download.

1.2.3 had fixed some issues I'd had with some network cards, but those were pretty minor compared to non-functional IPSec.

If any developer wants help testing or debugging this issue I'd be happy to reinstall the latest snapshot and work with them on it. I've got access to PIXs running 6.3.5 and 8.0.4 and a Concentrator 3005.

drees

@kapara:

Is anyone having a good experience with IPSEC lan to LAN with 1.2.3?

No issues here with 1.2.3 RC1 and Astaro 7.4 with IPsec VPNs. The Astaro box is even behind a NAT machine (a pfSense box ;-) so NAT-T appears to be working well, too.

We just got this particular setup up and running a couple days ago, no issues the entire time so far.

rwalker

Everyone that has posted above needs to update whether they are using parallel tunnels or not (meaning you have more than one network so a tunnel for each network). This problem existed in 1.2.2 and I am curious whether it has gotten worse or better.

Thanks,
Roy

drees

@rwalker:

Everyone that has posted above needs to update whether they are using parallel tunnels or not (meaning you have more than one network so a tunnel for each network). This problem existed in 1.2.2 and I am curious whether it has gotten worse or better.

I'm using 1.2.3 RC1 in a multi-tunnel setup with no problems for about a week now.

The pfSense side has two subnets, the other side (Astaro) has one.

The only issue I see is that the IPsec status screen shows the VPNs in state yellow instead of green, and one of the tunnels is missing the source network, yet the tunnels are working fine. They have been yellow for at least a couple days.

See the attached picture.

Green is the pfSense endpoint IP.
Red is the Astaro endpoint IP.
Pink is the Astaro LAN network
Blue is the pfSense LAN network

Note the missing LAN network in the first listed VPN and how the status is yellow on both. But both VPNs are functioning properly.

IPsec-Status.png_thumb

ankaerith

I am connecting to 3 Cisco PIXs with 6 tunnels.

PIX 1: 3 tunnels
PIX 2: 2 tunnels
PIX 3: 1 tunnel

PIX config:
crypto ipsec transform-set myset esp-3des esp-sha-hmac
crypto map outside_map 40 ipsec-isakmp
crypto map outside_map 40 match address outside_cryptomap_40
crypto map outside_map 40 set pfs group2
crypto map outside_map 40 set peer 1.1.1.1
crypto map outside_map 40 set transform-set myset
isakmp key ******** address 1.1.1.1 netmask 255.255.255.255
isakmp identity address
isakmp policy 42 authentication pre-share
isakmp policy 42 encryption 3des
isakmp policy 42 hash md5
isakmp policy 42 group 2
isakmp policy 42 lifetime 86400
isakmp policy 62 authentication pre-share
isakmp policy 62 encryption 3des
isakmp policy 62 hash sha
isakmp policy 62 group 2
isakmp policy 62 lifetime 86400

PFSense:

Phase 1:
Negotiation mode: MAIN
My identifier: MY IP
Encryption algorithm: 3DES
Hash algorithm: SHA1
DH key group: 2
Lifetime: 28800
Authentication method: pre-shared

Phase 2:
Protocol: ESP
Encryption algorithm: 3DES
Hash algorithms: SHA1 , MD5
PFS key group: 2
Lifetime: 86400

Works perfectly on 1.2.2.

rwalker

The issue is only between pfSense <-> pfSense. Between any other device I have tested it works without a problem (parallel tunnels or not). I have now upgraded a few of our firewalls to 1.2.3RC1, so will see what happens.

Roy

podilarius

Well just tested with NAT-T enabled and mine is now working!!! Thanks guys, truly wonderful.

sigma

At the moment I use 1.2.3 RC2 and have also a similar problem, but not the same as written here. I only have troubles to access over VPN if I'm on the WLAN port. No problems at all on the LAN port. On the other side an old ZyWall 30W is working.

I now disabled NAT-T because it's the only hint I found here. So I cann tell more about that tomorrow or so.

After a reboot I have again acces over vpn from WLAN for a few hours until it's broken again. And as I told, after it is brolen on WLAN it works fine in LAN.

Sigma

databeestje

We were trying ipsec-tools 0.8 during that timeframe to fix a number of DPD issues with tunnels not re-negotiating.

This proved to cause lot's of issues with parallel tunnels.

So we backed out the change and went back to 0.7.2. We will be merging 0.7.3 soon which was just released.

It has a few small fixes but unlikely to break things.