Howto boot a 1.2.3 nano image on embedded ??
-
i wrote pfSense-1.2.3-20090705-2323-nanobsd.img.gz to a 2gb cf card an put i t into a alix board.
after power on and bios messages i get this screen:PC Engines ALIX.2 v0.99
640 KB Base Memory
261120 KB Extended Memory01F0 Master 848A ST625211CF
Phys C/H/S 4845/16/63 Log C/H/S 605/128/631 FreeBSD
2 FreeBSDBoot: 1
what have i to do now? every keyboard input makes a # on the sreen.
-
Did you try just letting it go without touching anything? I'm running that image on a 2GB card in an Alix 2d3 just fine. I didn't touch the console, just got into the webgui after it booted.
-
no i didn't. i was expecting the pre-setup for interface assignment and ip-adress setting.
i will have a try. -
The new embedded snaps default to vr0 and vr1 for LAN/WAN, so you can boot them without going through the interface assignment.
-
Did you find a solution to this problem. Have the same here. It don't boot automatic. And Key entries result in a #
Sigma1
i wrote pfSense-1.2.3-20090705-2323-nanobsd.img.gz to a 2gb cf card an put i t into a alix board.
after power on and bios messages i get this screen:PC Engines ALIX.2 v0.99
640 KB Base Memory
261120 KB Extended Memory01F0 Master 848A ST625211CF
Phys C/H/S 4845/16/63 Log C/H/S 605/128/631 FreeBSD
2 FreeBSDBoot: 1
what have i to do now? every keyboard input makes a # on the sreen.
-
Flash your alix to 0.99h then works fine
-
Thanks, but where I get this release? On pcEngines I get some Source of tinybios, but have no chance to get a working file (I think I need an assembler (not free). Or are there standard bios files for download. If yes, I can't find it.
Sigma
-
The Bios on this side
http://www.pcengines.ch/alix2.htm
-
I have this same problem, but with a new twist. I'm using a WRAP instead of an ALIX.
PC Engines WRAP.1C/1D/1E v1.08 640 KB Base Memory 130048 KB Extended Memory 01F0 Master 044A CF CARD 4GB Phys C/H/S 7818/16/63 Log C/H/S 977/128/63 1 FreeBSD 2 FreeBSD Boot: 1 ###################################I know there is a v1.11 bios for the WRAP, but I don't use the minipci port, also I've already talked to someone running the latest bios and they still have this issue.
Ideas?
-
This appears to be from the use of packet mode. A commit just went in to take it out of future images, or if you can mount the image in another bsd box, you can type:
boot0cfg -o nopacket /dev/<whatever></whatever>Where <whatever>is the device name that the CF appears as (e.g with my USB CF reader it's da0)</whatever>
-
On the ALIX I wrote a new BIOS and after that it works fine. Have a look for a new BIOS for your WARP.
-
On the ALIX I wrote a new BIOS and after that it works fine. Have a look for a new BIOS for your WARP.
FYI- That doesn't help. I updated to the newest one and it still didn't boot without switching to nopacket.
-
It's possible. WARp is not ALIX, but it was worth a try :-)
-
It's possible. WARp is not ALIX, but it was worth a try :-)
Yeah, it was worth a try, which is why I'd already tried it :-)
With the nopacket changes in, I wonder if an ALIX with an older BIOS will boot it now as well.
-
I got the hint with to upgrade the BIOS from Stoffel (thanks again!!) and I'm glad that it works so fine now.
I see in another thread that packages can't be installed on the nanobsd image. This seems to be because of the read only filesystems, I think for protecting the CF from intensive writing. I tried some things to mount the filesystems rw, but had no chance, because I have less experience with freebsd. I tried it also with a live system, could access the image but I had to less rights to do that …:-)
So a good Idea will be to set the needed filesystems to rw, install some packages and after a boot it was back ro again. So I think the CF is safe enough. Some uses microdrives or small harddisk, and in this case it will be an option, that the filesystems can be set to rw.
I don't know where to write this idea (and I'm also sure that I'm not the first with this) but I would haf fun if this could be realized.Sigma
-
Packages on nano will definitely need some fine tuning. The ability to install them is a very, very new feature so some things are bound to take time to settle.
iirc, there will need to be some updates to some packages so that they can do what they need, and it may end up that not every package will be nano-friendly.
Time will tell, and you'll have to contact each package maintainer about issues.
-
jimp, thanks for this information. I have a look to the forum and new upgrades :-)
boot problem:
I tried the actual 4g snapshot. I have the same effect as I had with versions before. No problem on "normal" CF cards, but php errors at boot with the SLC CF version. It's not important for me, but if someone has the same effect take non SLC cards so it works (but only with BIOS 0.99h on ALIX boards).Sigma
-
I tried the http://snapshots.pfsense.org/FreeBSD_RELENG_7_2/pfSense_RELENG_1_2/nanobsd/pfSense-1.2.3-4g-20090709-0538-nanobsd.img.gz and go the same hash mark stuff on my WRAP. I'm currently downloading http://snapshots.pfsense.org/FreeBSD_RELENG_7_2/pfSense_RELENG_1_2/nanobsd/pfSense-1.2.3-1g-20090709-1710-nanobsd.img.gz to give that a shot and see if it's fixed in that build.
edit: Updated my WRAP to v1.11, still got #### from that newer snapshot.
edit2: As of the http://snapshots.pfsense.org/FreeBSD_RELENG_7_2/pfSense_RELENG_1_2/nanobsd/pfSense-1.2.3-4g-20090710-0645-nanobsd.img.gz snapshot, I now have a working nanobsd on my WRAP.
-
i have a alix with 0.99 bios and all nanobsd images after 11th july boot up just fine
-
anyone got a solution how to boot from wrap ? i can´t get it to work
thanks
