Upgrade Pfsense system 23 july For Multi WAN + MULTI LAN (Open vpn, Wireless)

idelta

bug that wasn't allowing the state table to clear out normally
You are right. Version 20090614-0015. Tried every (and many more) :
net.inet.tcp.hostcache.expire=1
net.inet.tcp.keepidle=30000
net.inet.tcp.keepintvl=5000
net.inet.tcp.finwait2_timeout=15000
net.inet.tcp.fast_finwait2_recycle=1
kern.ipc.somaxconn=32768
net.inet.icmp.icmplim=3000
kern.ipc.maxsockets=300000
net.inet.tcp.delayed_ack=1
net.inet.tcp.maxtcptw=196607

Nothing solves the problem : State table growing inevitably !
I would not like to kill more or less running system.
How do we know that the problem is solved ?

"State Timeout in seconds" in Advanced options for firewall rules also does no effect !

jimp

@idelta:

bug that wasn't allowing the state table to clear out normally
You are right. Version 20090614-0015. Tried every (and many more) :

It was fixed today, the most current updates have been confirmed to work by several people.

Try this snapshot, or later:
http://snapshots.pfsense.org/FreeBSD_RELENG_7_2/pfSense_RELENG_1_2/updates/pfSense-Full-Update-1.2.3-20090614-1815.tgz

DeCex

Try this snapshot, or later:
http://snapshots.pfsense.org/FreeBSD_RELENG_7_2/pfSense_RELENG_1_2/updates/pfSense-Full-Update-1.2.3-20090614-1815.tgz

Yey, been up over 2h now, i guess is fixed, thanks

gladizxx

After I upgraded to version 1.2.3-20090614-0015, all with normal pfsense running back, then I upgrade to the latest version 20090616–0034 Pfsense running very wonderfull, internet connection the more aggressive, Load Balance running optimally, as if the entire resource that have empowered perfectly. While the IP Sec're setting me back, because of internal reasons. From there I use my old Pfsense, once I find new problems, while the rest are internal constraints on me. :)

gladizxx

It seems PFsense, near the start …. stable release .... :D

Sylhouette

I use RC2
1.2.3-RC2
built on Wed Jun 24 00:36:43 EDT 2009

It runs on a soekriss 5501, but after a couple of days it stalls, no traffic is coming through any more.
I can still ping the box but it hangs.
only a power cycle gets it going again.

It is my main router so i can not investigate the state and need to reboot as quickly as possible.
Is has 3 interfaces enabled.
vr0 LAN
vr1 WAN pptp
vr2 DMZ

Further more nothing special.
No traffic shaping load balance or other stuff.

I use revert back to 1.2 now to make sure i get no calls in the evening about a dead router.

No complains, just an observation!

regards,
Johan

gladizxx

I have several multi wan router, which I apply on some SOHO multiclient. I always update the pfsense 1.2.3. RC2 latest updater, ( http://snapshots.pfsense.org/FreeBSD_RELENG_7_2/pfSense_RELENG_1_2/updates/ ). In fact I have never experienced problems with the router, all interface with the normal running. The only true version of the updater prior to the current still found the log loadbalance (as in the sticky ( http://forum.pfsense.org/index.php/topic, 16671.0.html ) and I really understand it, because it does not disrupt the performance of the router in general. And up to now all of my router is running normally, without any obstacles that means.

Not trying to defend. :)
just the story of the fact that I experienced. ;D

THKS

Sylhouette

i think i have been bitten by the following:

http://cvstrac.pfsense.com/tktview?tn=1935

regards,
Johan

pfsense_fan009

@gladizxx:

It seems PFsense, near the start …. stable release .... :D

changes from 16juni?

which version is the latest working? (the latest gives me a huge problem,can't do anything anymore)

gladizxx

One Pfsense used for the Multi-WAN, Multi-LAN (wireless, openvpn) can run Load Balance with Normal. Just log on the load balance constraints are still there ….. :)