1.2.3 RC3 Captive Portal not working..no Redirection
-
It's because I have 3 subnets connected to the LAN interface.
172.20.30.0/24
172.20.20.0/24
172.20.10.0/24 -
Someone else in another thread had a similar issue and it ended up being squid causing the bypass.
-
hmmm..not using squid.
-
It's because I have 3 subnets connected to the LAN interface.
172.20.30.0/24
172.20.20.0/24
172.20.10.0/24that doesn't change the basic point: you should not have overlapping subnets. try something like OPT1 being 172.20.128.0/24 and make the LAN subnet mask /17 (or whatever?)
-
yes..I understand that now. Was wondering if that was the reason for CP not working….
-
no idea. try fixing it and see :)
-
I have the same problem running the embedded version of the software, I can get the captive portal to work fine on a full live cd install. I wonder if there is something missing in the embedded version… Only difference was I ran captive portal on the lan on the full install and on the wireless or opt2 on the embedded. It shouldn't matter which interface it is set up on though. Everything else was set up exactly the same.
UPDATE...
Did you set up passthrough for your dns ips?? As soon as I did that the captive portal kicked right in... That was the one difference I had between the 2 setups.
-
What do you mean by passthrough? Is that a checkbox on one of the DNS pages? Or do you mean a firewall rule of some kind?
Thanks,
Mark
-
in the captive portal page there is a tab at the top "Allowed IP addresses"
click on that
in there you click add "+"
chose "to" in the direction
put the dns ip in the ip address field
add your description *dns1" or whatever you want
then click save
make sure to make one for each dns ip you have for failover purposes
-
Still have the same problem. No problem accessing the internet….
and I made the changes... IE
OPT1 172.20.128.0/24 with OPT1 interface 172.20.128.1
LAN 172.20.30.0/17 with LAN interface 172.20.30.1
Whenever I connect on that subnet I automatically get internet access no page redirect at all. ???
-
Sooooooooo fustrating….
Another interesting fact...
I cannot ping the OPT1 int ip of 172.20.128.1 unless I open a browser and go the http://172.20.128.1 and then it give me the portal page. After I log in I can ping the OPT1 int ip.
This should be an easy config...
-
What are your OPT1 rules like? I have a similar setup on nano rc3 running fine. LAN is open, OPT1 is the wireless card, on a separate subnet. My OPT1 rules are:
BLOCK * OPT1 net * LAN net * * Wireless not allowed to access LAN
PASS * OPT1 net * * * * Wireless allowed outI have nothing in the Allowed IP addresses in the CP config. Wireless clients are getting DHCP/DNS from pfSense.
-
I think you can make this one rule. Make the destination !LAN?
-
I also have CP working fine on nano, it didn't take anything special. Not even any special allow rules for IPs.
I posted my settings in another thread.
-
same problem with squid lastest version
-
Has squid ever worked with Captive Portal?
I didn't think the two were compatible, but I could be wrong (I don't use CP much)
-
Only on 2.0 i think it will work right.
Even there i think some tweaking is needed for this..Try on 2.0 if it does not work open a bug report on redmine.pfsense.org.
-
Thanks for the clarification, ermal. I suspected as much but it's nice to know for sure.
