Pass all traffic through OpenVPN tunnel

[GruensFroeschli]

Well no, this only enables you to create rules for an assigned interface.
To assign interfaces, you do the same as if you assign a real interface ( firewall -> assign )

[yamahabest]

Things I've done:

• I have added tun0 as OPT1 interface.
• I have added a firewall rule on the OPT1 interface: ***  OPT1 net  *  *  *  *      Default OPT1 -> any**

I am still unable to connect to any webpage.

I haven't set any parameters on the OPT1 interface (Interface > OPT1 page). Do I need to do this?

Or do I need to do some other settings?

[AhnHEL]

You need an Advanced Outbound NAT rule in place with the virtual Tunnel network as the Source address.

Firewall/NAT/Outbound


[GruensFroeschli]

Hmmm.
It appears the sentence

Every locally connected subnet, whether defined and reachable via a static route or attached to a LAN or OPT interface, will have its outbound traffic leaving any WAN interfaces NATed to that WAN interface's IP.

is no longer valid.
I never run into this issue, since i almost always write my outbound rules manually.

You can simply enable AoN under "firewall –> nat --> outbound" and copy the autocreated rule.
Change in the copy the subnet to the IP range you use for your OpenVPN connections.

[yamahabest]

I've enabled AoN and copied the autocreated rule.

The autocreated rule was: WAN    192.168.2.0/24  *  *  *  *  *  NO  Auto created rule for LAN
The rule I've added: WAN    192.168.200.0/24  *  *  *  *  *  NO  OpenVPN

The 192.168.200.0 address is copied from the OpenVPN page.

However I'm still unable to connect to the internet after doing this.

Do I need to undo the steps below?

• I have added tun0 as OPT1 interface.
• I have added a firewall rule on the OPT1 interface: *      OPT1 net      *      *      *      *            Default OPT1 -> any

Or do I have to do other steps?

[yamahabest]

GruensFroeschli, onhel or anyone, do you have any ideas?

[AhnHEL]

Since you are using AON, undo the OPT1 tun0 interface.

Post your OpenVPN logs on your pfsense box and also your connection logs on your OpenVPN client so we can see whats going.

From what I've read, you followed the tutorial to the letter including using the exact IP networks?

[yamahabest]

Things I've done:

• I have deleted a firewall rule on the OPT1 interface: *      OPT1 net      *      *      *      *            Default OPT1 -> any.
• I have deleted tun0 as OPT1 interface.
• I have disabled the Disable auto-added VPN rules option.

Internet is now working! If I go to http://whatismyipaddress.com/ I see the correct IP Address, so the connection is correctly routed through the tunnel.
Many thanks for helping!

I have just one question left. I have now enabled Manual Outbound NAT rule generation (Advanced Outbound NAT (AON)), does this has any disadvantages as regards to Automatic outbound NAT rule generation (IPsec passthrough)?

[AhnHEL]

Looks like what fixed it was unchecking the 'Disable Auto Added VPN rules' AND setting up the AON.

AON is required when using the redirect-gateway option so there is no advantage/disadvantage.

[mayesjc]

Following this thread did not solve everything until I added the addresses of DNS servers in the OpenVPN server configuration page under the "DHCP-Opt.: DNS-Server" option.  In may case I added the addresses for OpenDNS, although I doubt that matters.