PPPoE reconenction fix - mpd fix ($100)
-
realtek work fine for me always on same isp but this vr is an issue with almsot 4 different isps i have tested in 2 countries
It works with a switch in between?
-
ys because that way the port never goes down, the issue is when its connected to the isp fiber optic modem and that power offs which results in the port going completely down or some wierd state after which when on the packets from mpd never reach the isp at all inspite of port being on again
-
Sounds like a $5 solution….
-
switch solves the issue but isnt the proper solution.
its like some1 saying adding a switch to a switch to make a network connection for a PC but all u end up with is unnecessary switches when the PC can connect to the first switch directly or a better eg would be like adding a switch to connect 2 cat5 cables when u can simply plug in a coupler
-
It might not be a proper solution, however, lets be realistic here. This probably will not ever get solved. Assumes a whole LOT more detail on the HW involved plus - I'm afraid - involves getting developers to get their hands on that very HW/ISP connectivity for testing/debugging. So, however harsh that may sound - certainly not a question of a $100 bounty.
-
the reason this thread is still active because the developer has the redmine ticket still open as well as ermal last time said he would come back to this issue so was just checking as that post was quiet some time ago.
if its never going to be fixed then they might simply close this bounty as well as the redmine ticket once and for all
-
It's worth leaving open yet, there is a chance it may work again once we get 2.2 snapshots going on FreeBSD 10.x, newer driver set an all.
-
any eta on when thats going to happen?
the weird thing about this issue is that even the most crappiest routers in the market dont suffer this issue so it all cant be blamed on the DSLAM, if it was that then most other routers would also suffer that
-
No ETA on usable 10.x images. Could be months.
And the problem is a combination of factors - Specific Modem/ISP/DSLAM + Specific driver
-
to what i noticed is its just VIA drivers because it works fine with realtek, the isp modem i tested were 3 different types, zhone, huawei and cisco and it was same on all three, via chipset causing it, dslam which i tested was unisphere and the other was some unknown brand so the dslam, modem changed in all situations but alix was common so it suffered, i have 2 other pfsense full installs on the same isp using realtek and they work fine and always connect everytime
-
Wow, I missed this thread :)
Sorry for late reply…
Yes, vr0 had problems, DSLAM is UNISPHERE...
Dlink, realtek, intel and broadcom nics all worked great...
VIA on-motherboard NICs failed to connect...I tested all possibilities, from power outages to just cable disconnect and vr0 failed every time and others worked just fine EVERY time...
Regards,
Greg -
cant we take the vr drivers from FreeBSD 10.x and test it on current pfsense to see if it will actually fix this issue or no rather than wait for months for this to resolve coz its already over 2 years now
-
Well, I replaced my nics with Intel ones and that was it….
I needed stable system and Intel gave me that... -
cant we take the vr drivers from FreeBSD 10.x and test it on current pfsense to see if it will actually fix this issue
Possible but might not be trivial: FreeBSD internal interfaces and data structures might have changed significantly requiring considerable work to backport those changes as well or rewrite the vr changes from FreeBSD 8.3 to 10.x to work in FreeBSD 8.3 context.
Best case (assuming familiarity with FreeBSD kernel build procedures): maybe an hour or two to import the 10.x source into a 8.3 build system, recompile and run some basic tests.
Worst case: maybe up to a few months to figure out what changes in FreeBSD internals to backport and do them.
-
how about just check the drivers code and see the changes and cherry pick them which possibly might solve this network port stuck in a limbo state
-
Given how widespread the Alix install base is - pleeease, no. No backporting of vr drivers from FreeBSD 10.x to 2.1. While I can understand that it sucks for affected people
- this can apparently be extremely easily worked around by putting a switch between the pfsense box and the modem,
- this clearly affects a tiny percentage of users with specific NIC/modem/DSLAM combo on PPPoE specifically.
=> certainly not worth the risk of breaking everyone else
-
lets just leave it to the developers to decide, what they can do is provide the drivers separately to install so every1 dont need to use this
-
I have this issue and it occurs more frequently since updating to 2.0.3-RELEASE (i386).
I doubt a switch is going to make any difference in my case because I am running pfsense in a VM that effectively has an always up (virtual) switch, connected to a physical Intel E1000 card port patched straight into a routerboard (all gear on battery) so I am not getting disconnected because of a layer 1 issue.
I'm a bit lost at how to proceed. Running a script to tear down the interface and bring it back up if it's up and experiencing no throughput (but it is present) seems like the best bet
-
thats the only way to get back the link going, if u read few posts back, some1 did design a script for this and it actually worked, atleast to some extend
y dont everyone add some amount to this so some1 can develop a fix for this, probably a newer driver might solve it
-
thats the only way to get back the link going, if u read few posts back, some1 did design a script for this and it actually worked, atleast to some extend
y dont everyone add some amount to this so some1 can develop a fix for this, probably a newer driver might solve it
Thanks for the tip about the script. How can the bounty be added to apart from just making a note in my post?
