Lightsquid on 2.2 should be OK now

jimp

I pushed a fix just now for the graphs.

sqstat works fine for me. Keep in mind that sqstat only shows ACTIVE DOWNLOADS so unless you watch it like a hawk loading web pages barely will appear, long downloads will show.

jimp

@mir:

Just installed lightsquid today. Seems to work except for the following:

sqstat: page deletes history meaning only active connections at exactly the moment page is refreshed is shown. Should it not present a page connections was shown kind of like a rolling page?

graphs: When trying to see graphs a blank page is the result.

No, sqstat does not present a log, it is only the currently active at the moment connections. You're only likely to see long/large downloads there.

You may be thinking of the "real time" type view that I think Sarg has.

mir

@jimp:

You may be thinking of the "real time" type view that I think Sarg has.

Yes, this was what I have in mind.

mir

@jimp:

I pushed a fix just now for the graphs.

I can confirm graphs are showing now. Thanks.

kiekar

Hello Mir,

I can confirm graphs are showing now. Thanks.

How were you able to get the graph to work. It's still not functioning for me :(

jimp

Reinstall lightsquid, press save on the lightsquid settings, load the report, click the graph icon and make sure to force a refresh (shift+reload)

kiekar

Hello Jimp,

Before I Uninstall lightsquid I want to make sure of the steps.

make sure to force a refresh (shift+reload)

shift is the shift key and reload is ?

jimp

The reload button on your browser. Or use ctrl-F5.

kiekar

Thanks Jimp, I'm installing the new version of lightsquid which I didn't realize was there.

kiekar

Worked perfectly, Thanks a lot for your contribution.

mir

@jimp:

Reinstall lightsquid, press save on the lightsquid settings, load the report, click the graph icon and make sure to force a refresh (shift+reload)

I dont think it is necessary to press save on settings since the settings will be reread automatically when you reinstall the updated package. I did not do this.

mrbasic

Tried all fixes, Not working :(

LigthSquid diagnostic.
Error : report folder '/var/lightsquid/report' not contain any valid data! Please run lightparser.pl (and check 'report' folder content)
Please check config file !

I am new to Pfsense. Where does config files located?

Tried Reinstall. I had Squidguard. Removed it, Reinstalled lightsquid. no progression.

jimp

Do you actually have log data from squid?
Did you actually press "Refresh full" on lightsquid settings and wait?

If you followed the directions at https://doc.pfsense.org/index.php/Lightsquid_Troubleshooting then you may not have an actual lightsquid problem, but a problem elsewhere leading it to not have data. Probably worth starting a fresh thread for.

hvac14400

@jimp:

sqstat works fine for me.

really?

Proxy Squid: Realtime stat (sqstat)

Warning: gethostbyaddr(): Address is not a valid IPv4 or IPv6 address in /usr/local/www/sqstat/sqstat.class.php on line 426

Squid RealTime stat 1.20 for the proxy server squid/3.4.10

URI Curr. Speed Avg. Speed Size Time
Total: 1 users and 1 connections @ 0.00/0.00 KB/s (CURR/AVG)
Total: 1 users and 1 connections @ 0.00/0.00 KB/s (CURR/AVG)

not working at all for me.

jimp

Not sure about the error at the top, but when I tested it, clients with long, active downloads showed in the list just fine.

hvac14400

i can tell you about error at the top - sqstat.class.php

if ($connection) {
# username field is avaible in Squid 2.6 stable
if(substr($v,0,9) == "username ") $parsed["con"][$connection]["username"] = substr($v, 9);
if(substr($v,0,5) == "peer:") $parsed["con"][$connection]["peer"] = substr($v, 6);

wtf is this "peer" line here, while squid returns "remote" instead?
this shit right here just CAN'T work on any version above 3.1 or so - you must replace it with

if(substr($v,0,7)  == "remote:")    $parsed["con"][$connection]["peer"]     = substr($v, 8);

see?
but even then sqstat shows total BS - speed keep increasing constantly, etc.
so i really don't know, how is that possible

sqstat works fine for me.

:D
tested on fresh install of 2.2-RELEASE (amd64) built on Thu Jan 22 14:03:54 CST 2015 FreeBSD 10.1-RELEASE-p4
3.4.10_2 pkg 0.2.6
1.8.2 pkg v.2.35

hvac14400

and btw - there is more bugs in that php code

if(substr($v,0,3)=="me:") $parsed["con"][$connection]["me"]=substr($v,4);

probable need to be replaced with something like

if(substr($v,0,6)=="local:") $parsed["con"][$connection]["me"]=substr($v,7);

tho i saw no difference after that.

jimp

I don't doubt there are more bugs, I haven't ever touched the code inside there (or even looked).

I was using squid 2.7.x with it, which may explain why it worked for me.

hvac14400

@jimp:

I was using squid 2.7.x with it, which may explain why it worked for me.

yea, i think it's the case.

dld121

Uninstalled lightsquid from 2.2
I ran all the trouble shooting steps
Reinstalled lightquid into 2.2
clicked save on the settings page

ran the "./check-setup.pl" from the /usr/local/www/lightsquid path.

LightSquid Config Checker, 2005-9 Sergey Erokhin GNU GPL


LogPath   : /var/squid/logs
reportpath: /var/lightsquid/report
Lang      : /usr/pbi/lightsquid-i386/local/share/lightsquid/lang/eng
Template  : /usr/pbi/lightsquid-i386/local/www/lightsquid/tpl/base
Ip2Name   : /usr/pbi/lightsquid-i386/local/libexec/lightsquid/ip2name.ip

no: GD.PM found, please install or set $graphreport=0 to disable

tried the "pkg_add" step, but it doesn't work on 2.2 –- how do you fix this?

Thanks,
David