Lightsquid on 2.2 should be OK now

mrbasic

Tried all fixes, Not working :(

LigthSquid diagnostic.
Error : report folder '/var/lightsquid/report' not contain any valid data! Please run lightparser.pl (and check 'report' folder content)
Please check config file !

I am new to Pfsense. Where does config files located?

Tried Reinstall. I had Squidguard. Removed it, Reinstalled lightsquid. no progression.

jimp

Do you actually have log data from squid?
Did you actually press "Refresh full" on lightsquid settings and wait?

If you followed the directions at https://doc.pfsense.org/index.php/Lightsquid_Troubleshooting then you may not have an actual lightsquid problem, but a problem elsewhere leading it to not have data. Probably worth starting a fresh thread for.

hvac14400

@jimp:

sqstat works fine for me.

really?

Proxy Squid: Realtime stat (sqstat)

Warning: gethostbyaddr(): Address is not a valid IPv4 or IPv6 address in /usr/local/www/sqstat/sqstat.class.php on line 426

Squid RealTime stat 1.20 for the proxy server squid/3.4.10

URI Curr. Speed Avg. Speed Size Time
Total: 1 users and 1 connections @ 0.00/0.00 KB/s (CURR/AVG)
Total: 1 users and 1 connections @ 0.00/0.00 KB/s (CURR/AVG)

not working at all for me.

jimp

Not sure about the error at the top, but when I tested it, clients with long, active downloads showed in the list just fine.

hvac14400

i can tell you about error at the top - sqstat.class.php

if ($connection) {
# username field is avaible in Squid 2.6 stable
if(substr($v,0,9) == "username ") $parsed["con"][$connection]["username"] = substr($v, 9);
if(substr($v,0,5) == "peer:") $parsed["con"][$connection]["peer"] = substr($v, 6);

wtf is this "peer" line here, while squid returns "remote" instead?
this shit right here just CAN'T work on any version above 3.1 or so - you must replace it with

if(substr($v,0,7)  == "remote:")    $parsed["con"][$connection]["peer"]     = substr($v, 8);

see?
but even then sqstat shows total BS - speed keep increasing constantly, etc.
so i really don't know, how is that possible

sqstat works fine for me.

:D
tested on fresh install of 2.2-RELEASE (amd64) built on Thu Jan 22 14:03:54 CST 2015 FreeBSD 10.1-RELEASE-p4
3.4.10_2 pkg 0.2.6
1.8.2 pkg v.2.35

hvac14400

and btw - there is more bugs in that php code

if(substr($v,0,3)=="me:") $parsed["con"][$connection]["me"]=substr($v,4);

probable need to be replaced with something like

if(substr($v,0,6)=="local:") $parsed["con"][$connection]["me"]=substr($v,7);

tho i saw no difference after that.

jimp

I don't doubt there are more bugs, I haven't ever touched the code inside there (or even looked).

I was using squid 2.7.x with it, which may explain why it worked for me.

hvac14400

@jimp:

I was using squid 2.7.x with it, which may explain why it worked for me.

yea, i think it's the case.

dld121

Uninstalled lightsquid from 2.2
I ran all the trouble shooting steps
Reinstalled lightquid into 2.2
clicked save on the settings page

ran the "./check-setup.pl" from the /usr/local/www/lightsquid path.

LightSquid Config Checker, 2005-9 Sergey Erokhin GNU GPL


LogPath   : /var/squid/logs
reportpath: /var/lightsquid/report
Lang      : /usr/pbi/lightsquid-i386/local/share/lightsquid/lang/eng
Template  : /usr/pbi/lightsquid-i386/local/www/lightsquid/tpl/base
Ip2Name   : /usr/pbi/lightsquid-i386/local/libexec/lightsquid/ip2name.ip

no: GD.PM found, please install or set $graphreport=0 to disable

tried the "pkg_add" step, but it doesn't work on 2.2 –- how do you fix this?

Thanks,
David

KOM

Try this:

pkg install p5-gd

jimp

There should be no need for that with the current package. The gd library is there and the package should be invoking ldconfig to nudge the system to find it without such hacks.

Check to see if it's there at all:

find / -name "*GD*.so"