Error openvpn site to site not ping
-
You should normally use "tun" mode and there will be (at least) 3 subnets with different addresses and routing between them:
a) Local LAN
b) Tunnel subnet
c) Remote LAN -
modified. put to port 1195, tun, tcp ..
network 192.168.181.0/24 to change with the other vpn client, the problem still remains, only Configo dripping from the pfSense .. the machines to hand Failure. however the log is okay.screens side B
-
Why tcp? Why are you doing things differently than every walkthrough and guide tells you to do?
-
changed too, made using udp and tcp and I could not, I can only ping the pfSense.
lo0: flags=8049 <up,loopback,running,multicast>metric 0 mtu 16384 options=600003 <rxcsum,txcsum,rxcsum_ipv6,txcsum_ipv6>inet 127.0.0.1 netmask 0xff000000 inet6 ::1 prefixlen 128 inet6 fe80::1%lo0 prefixlen 64 scopeid 0x5 nd6 options=21 <performnud,auto_linklocal>enc0: flags=0<> metric 0 mtu 1536 nd6 options=21 <performnud,auto_linklocal>pppoe0: flags=88d1 <up,pointopoint,running,noarp,simplex,multicast>metric 0 mtu 1492 inet 189.XXX.XXX.205 --> 200.XXX.XXX.117 netmask 0xffffffff inet6 fe80::20d:b9ff:fe1a:4a54%pppoe0 prefixlen 64 scopeid 0x7 nd6 options=21 <performnud,auto_linklocal>ovpns1: flags=8051 <up,pointopoint,running,multicast>metric 0 mtu 1500 options=80000 <linkstate>inet6 fe80::20d:b9ff:fe1a:4a54%ovpns1 prefixlen 64 scopeid 0x8 inet 192.168.200.1 --> 192.168.200.2 netmask 0xffffffff nd6 options=21 <performnud,auto_linklocal>Opened by PID 23881 ovpnc2: flags=8051 <up,pointopoint,running,multicast>metric 0 mtu 1500 options=80000 <linkstate>inet6 fe80::20d:b9ff:fe1a:4a54%ovpnc2 prefixlen 64 scopeid 0x9 inet 192.168.181.6 --> 192.168.181.5 netmask 0xffffffff nd6 options=21 <performnud,auto_linklocal>Opened by PID 19975 tap1: flags=8842 <broadcast,running,simplex,multicast>metric 0 mtu 1500 options=80000 <linkstate>ether 00:bd:49:3d:07:01 nd6 options=21 <performnud,auto_linklocal>media: Ethernet autoselect status: no carrier</performnud,auto_linklocal></linkstate></broadcast,running,simplex,multicast></performnud,auto_linklocal></linkstate></up,pointopoint,running,multicast></performnud,auto_linklocal></linkstate></up,pointopoint,running,multicast></performnud,auto_linklocal></up,pointopoint,running,noarp,simplex,multicast></performnud,auto_linklocal></performnud,auto_linklocal></rxcsum,txcsum,rxcsum_ipv6,txcsum_ipv6></up,loopback,running,multicast>Internet: Destination Gateway Flags Netif Expire default 200.XXX.XXX.117 UGS pppoe0 8.8.8.8 200.XXX.XXX.117 UGHS pppoe0 127.0.0.1 200.XXX.XXX.117 UGHS lo0 177.XXX.XXX.XXX pppoe0 UHS pppoe0 189.XXX.XXX.XXX link#7 UHS lo0 192.168.2.0/24 link#2 U vr1 192.168.2.1 link#2 UHS lo0 192.168.10.0/24 192.168.181.5 UGS ovpnc2 192.168.181.0/24 192.168.181.5 UGS ovpnc2 192.168.181.5 link#9 UH ovpnc2 192.168.181.6 link#9 UHS lo0 192.168.200.0/24 192.168.200.2 UGS ovpns1 192.168.200.1 link#8 UHS lo0 192.168.200.2 link#8 UH ovpns1 200.XXX.XXX.XXX link#7 UH pppoe0 -
There is not an obvious problem there. Post the OpenVPN server settings at the other end and also the firewall rules on LAN and OpenVPN at each end.
Try traceroute between clients at each end and see where it stops, or if it starts going out some WAN - that will give you a clue about where things go wrong. -
follows the server screen .. site A
-
At minimum, you should specify the Site B subnet in the Site A "IPv4 Remote Network/s" box.
You need to let the server know it will be routing traffic for 192.168.2.0/24 through the OpenVPN conx.
Post the Site B Client screen as well to make sure nothing else is missing.
-
Site B Client screen
-
As has been said, you have no remote networks specified at either end. That's how pfSense knows what traffic to route over the tunnel.
-
Apr 19 16:10:49 openvpn[78509]: Closing TUN/TAP interface Apr 19 16:10:49 openvpn[78509]: /usr/local/sbin/ovpn-linkdown ovpnc2 1500 1558 192.168.181.6 192.168.181.5 init Apr 19 16:10:51 openvpn[78509]: ROUTE_GATEWAY 200.XXX.90.XXX Apr 19 16:10:51 openvpn[78509]: TUN/TAP device ovpnc2 exists previously, keep at program end Apr 19 16:10:51 openvpn[78509]: TUN/TAP device /dev/tun2 opened Apr 19 16:10:51 openvpn[78509]: do_ifconfig, tt->ipv6=0, tt->did_ifconfig_ipv6_setup=0 Apr 19 16:10:51 openvpn[78509]: /sbin/ifconfig ovpnc2 192.168.181.10 192.168.181.9 mtu 1500 netmask 255.255.255.255 up Apr 19 16:10:51 openvpn[78509]: /usr/local/sbin/ovpn-linkup ovpnc2 1500 1558 192.168.181.10 192.168.181.9 init Apr 19 16:10:51 openvpn[78509]: /sbin/route add -net 192.168.10.0 192.168.181.9 255.255.255.0 Apr 19 16:10:51 openvpn[78509]: /sbin/route add -net 192.168.10.0 192.168.181.9 255.255.255.0 Apr 19 16:10:51 openvpn[78509]: ERROR: FreeBSD route add command failed: external program exited with error status: 1 Apr 19 16:10:51 openvpn[78509]: /sbin/route add -net 192.168.181.1 192.168.181.9 255.255.255.255 Apr 19 16:10:51 openvpn[78509]: Initialization Sequence Completed -
You need 192.168.2.0/24 in the remote networks on the server. I believe you also need to put the 192.168.181.0/24 tunnel network in the client side.
-
was placed and not solved .. I will do with pfSense 2.1.5 for testing
-
Are you certain the remote hosts will respond to pings from foreign networks? This is often the firewalls on the destination hosts. What version are you using? There have been few problems with OpenVPN on 2.2, 2.2.1, and 2.2.2. No reason to change versions. All you have to do is configure it correctly.
-
pfsense 2.2.2
-
placed in the test environment (XenServer) two pfSense 2.1.5 doing via vpn openvpn. and it worked, same configuration. Will install version 2.2.2.
-
I have plenty of OpenVPN site-to-site links on 2.2.2 and they work fine just like they did in 2.1.5 - put the right subnets in Tunel, Local and Remote Network/s boxes on server and client, make sure the firewall rules on LAN and OpenVPN at both ends allow the relevant traffic - that is all there is to it.
When I setup a new office it takes only a couple of minutes to bring up OpenVPN site-to-site links back to our main offices, it really does work.
