PfBlockerNG v2.0 w/DNSBL

reggie14

To a certain extent, this isn't surprising. pfBlockerNG essentially has to Man-in-the-Midde HTTPS. If the ad is being loaded from an HTTPS server (I don't necessarily mean the page you're viewing, rather where the ad itself is coming from), then pfBlockerNG redirects you to its own little webserver running on your pfsense box, and, since is done over HTTPS, that webserver uses a generic, default certificate. It's a different cert than what is used for the pfsense WebGUI. For various reasons, pfBlockerNG uses the same certifcate for every blocked HTTPS resource. This creates a problem because the name in the certificate doesn't match the domain name of the blocked resource, which is why you see certificate warnings. There's no good way around this, though. Attempting to dynamically create valid certs off a CA running on the pfsense box would be both complicated and slow.

But, I'm a little surprised you're seeing warnings. I used to see warnings occasionally, but I haven't for a while. I thought browsers just started silently dropping HTTPS connections to external resources when there's a bad certificate.

Can you provide additional information to reproduce this? What browser are you using? What webpage were you accessing? If I can see an example, and maybe inspect a packet capture and page source code may be I can see what's going on.

mbarnes

What about setting your virtual address to 0.0.0.0? As that whole /8 is non-routable, you wouldn't get the cert error. It would just silently fail to load ads.

reggie14

@mbarnes:

What about setting your virtual address to 0.0.0.0? As that whole /8 is non-routable, you wouldn't get the cert error. It would just silently fail to load ads.

While that might hide the cert error, there would be downsides. First, some some pages will hang as they wait for the ad server to respond. Second, blackholing the traffic completely by setting the VIP to something other than the DNSBL webserver will disable alerts. That would create problems, because the regular ad-blocking lists WILL break some sites and mobile apps. The alerts are, by far, the easiest way to track down problems.

There are better plausible workarounds, but we need to see some examples to understand under what circumstances people run into cert errors.

BIGGRIMTIM

Sorry if this is stupid question. I am using OpenDNS and wondered if I can use DNSBL along with it? The only way I was able to get alert data was by changing the DNS settings on my PC.

Thanks.

doktornotor

@BIGGRIMTIM:

Sorry if this is stupid question. I am using OpenDNS and wondered if I can use DNSBL along with it? The only way I was able to get alert data was by changing the DNS settings on my PC.

Not in this way. If you point your clients to pfSense as DNS server and use OpenDNS as forwarders for Unbound, then yes it should work.

tonymorella

@Atlan:

I am receiving certificate invalid errors after enabling the DNSBL when navigating certain sites - so far the culprit seems to mainly be googleads.g.doubleclick.net when trying to serve content over an HTTPS enabled website.

The attempt still shows in the Alerts tab of pfBlockerNG, the main site still loads, but it seems to be wanting to use the firewall's self signed certificate as the certificate for the ad server host.

Did I miss a setting somewhere to prevent this from happening?

Ya ran into the same problem while beta testing, completely forgot about this issue until I read your post :) For a quick fix I created a CA and web certificate via pfsense GUI then copies this cert to /var/unbound/dnsbl_cert.pem which dnsbl light http will use. Then push out the CA to all the desktops, could be done via GPO or login scripts. With https://letsencrypt.org/ picking up traction, everything is going to be running over TLS or SSL soon going to have to implement this type of fix.

**EDIT: Sorry guys did a bad job on this post and what I was doing, it does not fix the underlying issue with the TLS stream being bad because the cert is not valid, reggie14 did a much better job testing this than I. In my setup is simply helped limit the errors in Chrome. Again just a quick fix that might help. Again sorry for the confusion.

FYI the update from Chrome 45 to 46 made a difference in what come up under security warnings:
http://arstechnica.com/information-technology/2015/10/chrome-finally-kills-off-the-http-https-mixed-content-warning/**

Thanks
Tony M

asterix

Getting this EasyList error for w/o elements.

[ DNSBL_EasyList - w/o Elements ] Download FAIL
Could not determine IP address of host.
Firewall and/or IDS are not blocking download.

doktornotor

@Asterix:

Getting this EasyList error for w/o elements.

[ DNSBL_EasyList - w/o Elements ] Download FAIL
Could not determine IP address of host.
Firewall and/or IDS are not blocking download.

Well that's not a package error. You need working DNS. :D


$ host easylist-downloads.adblockplus.org
easylist-downloads.adblockplus.org has address 148.251.139.76
easylist-downloads.adblockplus.org has address 144.76.100.145
easylist-downloads.adblockplus.org has IPv6 address 2a01:4f8:200:114f::2
easylist-downloads.adblockplus.org has IPv6 address 2a01:4f8:192:7126::2

tonymorella

@doktornotor:

@Asterix:

Getting this EasyList error for w/o elements.

[ DNSBL_EasyList - w/o Elements ] Download FAIL
Could not determine IP address of host.
Firewall and/or IDS are not blocking download.

Well that's not a package error. You need working DNS. :D
$ host easylist-downloads.adblockplus.org
easylist-downloads.adblockplus.org has address 148.251.139.76
easylist-downloads.adblockplus.org has address 144.76.100.145
easylist-downloads.adblockplus.org has IPv6 address 2a01:4f8:200:114f::2
easylist-downloads.adblockplus.org has IPv6 address 2a01:4f8:192:7126::2

Filter out easylist-downloads.adblockplus.org via DNSBL as well as add it to an allow alias and see if this helps. Depending out how you having things setup could be blocking. Host lookup most likely works because it's doing is via unbound. Just a thought let us know :)

Tony M

shopro

I must be doing something wrong as when I load a page containing ads the page load stops until ad servers are timed out. Also in Status -> Services, dnsbl is showed as stopped. Can't seem to find any error logs about it anywhere. Also my alerts tab is empty besides the Deny list.

I configured dnsbl as instructed on page 1 and have double checked everything to be the same way. Though maybe the reason is that my clients use my domain controller as their dns which forwards to pfsense which in turn forwards to OpenDNS. Any ideas where I went wrong?

tonymorella

@shopro:

I must be doing something wrong as when I load a page containing ads the page load stops until ad servers are timed out. Also in Status -> Services, dnsbl is showed as stopped. Can't seem to find any error logs about it anywhere. Also my alerts tab is empty besides the Deny list.

I configured dnsbl as instructed on page 1 and have double checked everything to be the same way. Though maybe the reason is that my clients use my domain controller as their dns which forwards to pfsense which in turn forwards to OpenDNS. Any ideas where I went wrong?

dnsbl show as stopped is not a good sign, are you sure dnsbl check box is enabled as well as unbound (DNS Resolver)?

shopro

@tonymorella:

@shopro:

I must be doing something wrong as when I load a page containing ads the page load stops until ad servers are timed out. Also in Status -> Services, dnsbl is showed as stopped. Can't seem to find any error logs about it anywhere. Also my alerts tab is empty besides the Deny list.

I configured dnsbl as instructed on page 1 and have double checked everything to be the same way. Though maybe the reason is that my clients use my domain controller as their dns which forwards to pfsense which in turn forwards to OpenDNS. Any ideas where I went wrong?

dnsbl show as stopped is not a good sign, are you sure dnsbl check box is enabled as well as unbound (DNS Resolver)?

Yes, both dnsbl and unbound check box's are checked. The funny thing is that it blocks the ad's when enabled, but doesn't seem to use the 1x1 gif and instead just times out the servers.

tonymorella

@shopro:

@tonymorella:

@shopro:

I must be doing something wrong as when I load a page containing ads the page load stops until ad servers are timed out. Also in Status -> Services, dnsbl is showed as stopped. Can't seem to find any error logs about it anywhere. Also my alerts tab is empty besides the Deny list.

I configured dnsbl as instructed on page 1 and have double checked everything to be the same way. Though maybe the reason is that my clients use my domain controller as their dns which forwards to pfsense which in turn forwards to OpenDNS. Any ideas where I went wrong?

dnsbl show as stopped is not a good sign, are you sure dnsbl check box is enabled as well as unbound (DNS Resolver)?

Yes, both dnsbl and unbound check box's are checked. The funny thing is that it blocks the ad's when enabled, but doesn't seem to use the 1x1 gif and instead just times out the servers.

If the dnsbl web server is not running this is what I would expect, request will not have a response and will time out. Anything in /var/log/pfblockerng/dnsbl_error.log and dnsbl.log files?

shopro

The dnsbl_error.log seems normal, no errors or anything else like that. The dnsbl.log says "Log file is empty or does not exist." which I assume is because the service isn't started.

shopro

@shopro:

The dnsbl_error.log seems normal, no errors or anything else like that. The dnsbl.log says "Log file is empty or does not exist." which I assume is because the service isn't started.

Got it working by completely removing the package and settings and reinstalling, removing settings was the key though no idea what was wrong. Now it starts as it should.

AndrewZ

Upgraded to 2.0, now always see the yellow sign on the status page with the following tooltip:

pfBlockerNG deDuplcation is out of sync. Perform a Force Reload to correct.

Tried Force Reload, Update, Cron, selecting/de-selecting deduplication is settings - nothing helps.
This warning goes off only if deduplication is disabled.

Clipboard01.jpg_thumb

doktornotor

@tonymorella:

Host lookup most likely works because it's doing is via unbound. Just a thought let us know :)

Well, it's not. Also not blocked, otherwise it'd be resolved to the DNSBL VIP.

@AndrewZ:

Tried Force Reload, Update, Cron, selecting/de-selecting deduplication is settings - nothing helps.
This warning goes off only if deduplication is disabled.

Probably easier to just wipe the lists:


rm -rf /var/db/pfblockerng/

Reinstall the package and run 'Force Update' after that.

BBcan177

@Atlan:

I am receiving certificate invalid errors after enabling the DNSBL when navigating certain sites - so far the culprit seems to mainly be googleads.g.doubleclick.net when trying to serve content over an HTTPS enabled website.

@Atlan, As indicated in reggie14's post, if you can reply back with the following questions below and we can go from there.

@reggie14:

Can you provide additional information to reproduce this? What browser are you using? What webpage were you accessing? If I can see an example, and maybe inspect a packet capture and page source code may be I can see what's going on.

@shopro:

@shopro:

The dnsbl_error.log seems normal, no errors or anything else like that. The dnsbl.log says "Log file is empty or does not exist." which I assume is because the service isn't started.

Got it working by completely removing the package and settings and reinstalling, removing settings was the key though no idea what was wrong. Now it starts as it should.

If there are errors starting/stopping the DNSBL service, those will be logged to the pfSense System log. The RC file for the DNSBL service is here (/usr/local/etc/rc.d/dnsbl.sh [stop|start|restart])

@shopro:

The dnsbl_error.log seems normal, no errors or anything else like that. The dnsbl.log says "Log file is empty or does not exist." which I assume is because the service isn't started.

The dnsbl_error.log is actually an error log for DNSBL Lighttpd. I will be renaming this file to something else to avoid this confusion. This log is used to collect any HTTPS alerts from the Lighttpd conditional error process (debug.log-condition-handling option).

@AndrewZ:

Upgraded to 2.0, now always see the yellow sign on the status page with the following tooltip:

This warning indicates that the masterfile is out of sync with the files in the /deny folder. This is a new feature that was added to v2.0 to warn users about this issue. Usually running a 'Force Reload' is sufficient to fix that warning; however, clearing out all the files and starting fresh might be needed in certain conditions. If this is still an issue, please review the pfblockerng.log file for other clues.

@doktornotor:

Probably easier to just wipe the lists:
rm -rf /var/db/pfblockerng/
Reinstall the package and run 'Force Update' after that.

Can also just uncheck 'Keep Settings' and Disable 'pfBNG' and 'Save' which will do the same :)

@doktornotor:

@Asterix:

Getting this EasyList error for w/o elements.

[ DNSBL_EasyList - w/o Elements ] Download FAIL
Could not determine IP address of host.
Firewall and/or IDS are not blocking download.

Well, it's not. Also not blocked, otherwise it'd be resolved to the DNSBL VIP.

I will be adding another validation on failed downloads to check if the 'Host Address' returns as the DNSBL VIP address (Meaning DNSBL is blocking the download), and adding that to the Error Response. But yes, if the error is "Could not determine IP address of host.", then there was another issue with the DNS lookup that failed. If DNSBL was blocking this download, that error message would not be displayed.

docjay

@BBcan177

'If there are errors starting/stopping the DNSBL service, those will be logged to the pfSense System log. The RC file for the DNSBL service is here (/usr/local/etc/rc.d/dnsbl.sh [stop|start|restart])'

I didn't see anything logged in my system log to help me identify my problem. Luckily I saw your post - :)

My DNSBL service won't start. When I attempt to start it from command line it comes back with:


[2.2.5-RELEASE][root@cerberus.home]/root: /usr/local/etc/rc.d/dnsbl.sh start
2015-11-22 12:06:31: (network.c.542) SSL: BIO_read_filename('/var/unbound/dnsbl_cert.pem') failed

when I dive into 'var/unbound/' there is no 'dnsbl_cert.pem' file.

I would rather not lose all of my settings to reinstall the package. I've already tried this with the box checked 'keep settings' but it still didn't let the service start. Is there a way to get the file 'dnsbl_cert.pem' or a way to backup my settings and reapply them after I completely wipe the package?

thank you!

;D

BBcan177

@docjay:

Is there a way to get the file 'dnsbl_cert.pem' or a way to backup my settings and reapply them after I completely wipe the package?

If you run 'Force Update' that pem file should be automatically created.