Openvpn issue - site 2 site

maverick_slo

So you can repro?

cmb

So you can repro?

No. Steve just figured there must be something to it. This all works fine with TLS and user auth on latest version, and nothing there has changed in some time. I upgraded a variety of test and production setups to latest and they all still work fine, and did a couple new configs from scratch which also worked fine.

Could you get me into your system to review? Can PM me to arrange specifics if so.

maverick_slo

There was snapshot issue or bad upgrade.
Now I`m on 2.3.b.20160115.1858 and roadwarrior works.

Now I have to test SSL/TLS peer to peer to confirm that working too.

maverick_slo

peer2peer still not working between 2.3 and 2.2.6

Client error: openvpn[56391]: ERROR: FreeBSD route add command failed: external program exited with error status: 1
Server no error.

maverick_slo

hmmmm could it be topology issue on 2.2.6?
mismatch between 2.3 server (subnet) and 2.2.6 client (net30) ?

maverick_slo

UPDATE:
If I leave all settings like they were and change only from SSL/TLS TO shared key VPN works.
With TLS I get that add route error.

wth??? :)

maverick_slo

There is no way at all for me to connect 2.3 box to 2.2.6 with Openvpn SSL/TLS.
With shared key it works just fine.

maverick_slo

Guys I found the error.
Look at screenshot.
Shared key and ssl/tls don`t have same settings under tunnel options.

ssltls.JPG_thumb

shared_key.JPG_thumb

maverick_slo

Shared key works for me, SSL/TLS not.

maverick_slo

In addition, when changing modes (shared key to ssl/tls) firefox needs like 15 seconds to display other options while IE changes options instantly.

EDIT:
This only happens on firefox NIGHTLY build, so nevermind that.

maverick_slo

Configs:

Working shared key server config:

dev ovpns2
verb 1
dev-type tun
tun-ipv6
dev-node /dev/tun2
writepid /var/run/openvpn_server2.pid
#user nobody
#group nobody
script-security 3
daemon
keepalive 10 60
ping-timer-rem
persist-tun
persist-key
proto udp
cipher AES-128-CBC
auth SHA1
up /usr/local/sbin/ovpn-linkup
down /usr/local/sbin/ovpn-linkdown
local MY WAN IP
ifconfig 172.16.91.1 172.16.91.2
lport 1199
management /var/etc/openvpn/server2.sock unix
push "route 10.10.0.0 255.255.255.0"
route 192.168.1.0 255.255.255.0
secret /var/etc/openvpn/server2.secret 
comp-lzo adaptive

Not working SSL/TLS config:

dev ovpns2
verb 1
dev-type tun
tun-ipv6
dev-node /dev/tun2
writepid /var/run/openvpn_server2.pid
#user nobody
#group nobody
script-security 3
daemon
keepalive 10 60
ping-timer-rem
persist-tun
persist-key
proto udp
cipher AES-128-CBC
auth SHA1
up /usr/local/sbin/ovpn-linkup
down /usr/local/sbin/ovpn-linkdown
local MY WAN IP
tls-server
ifconfig 172.16.91.1 172.16.91.2
lport 1199
management /var/etc/openvpn/server2.sock unix
push "route 10.10.0.0 255.255.255.0"
route 192.168.1.0 255.255.255.0
ca /var/etc/openvpn/server2.ca 
cert /var/etc/openvpn/server2.cert 
key /var/etc/openvpn/server2.key 
dh /etc/dh-parameters.1024
crl-verify /var/etc/openvpn/server2.crl-verify 
tls-auth /var/etc/openvpn/server2.tls-auth 0
comp-lzo adaptive
topology subnet

cmb

@maverick_slo:

Guys I found the error.
Look at screenshot.
Shared key and ssl/tls don`t have same settings under tunnel options.

They're not supposed to have all the same settings. Which specific setting are you referring to?

maverick_slo

Local subnet for example

maverick_slo

Tunnell settings MUST be same only encryption should vary. 2.2.6 has same tunnell settings for both methods and encryption different which is ok.
Clearly there is something wrong with openvpn gui and how it generates config.
Between 2.2.6 no problem at all.

Steve_B

There is a difference between the Tunnel settings display (Peer to peer (Shared Key) ) 2.2.x vs 2.3

I will correct that. I'm sure it will make a difference to the shared configuration though. I will make a note here once a correction has been pushed and perhaps you would let me know if you see any improvement.

Thanks for continuing to work on this!

maverick_slo

Thanks Steve!

I sure will test it because I need it :)

Steve_B

Researching this further I find that although the IPv4 Local network(s) and IPv6 Local network(s) controls are hidden when "Peer to peer (shared Key)" is selected, that is the desired behavior since they make no sense in a peer to peer environment. Whether they are hidden or not, the values are ignored so it really makes no difference.

There was a display bug in 2.2.x that caused the controls to be displayed.

So if we are to track down a potential GUI problem, the best approach would be to set up identical server configurations in 2.2.6 and in 2.3 and to then compare the /cf/conf/config.xml files looking at the <openvpn-server>section.

Is that something you could do?</openvpn-server>

maverick_slo

On it.

maverick_slo

@Steve_B:

Researching this further I find that although the IPv4 Local network(s) and IPv6 Local network(s) controls are hidden when "Peer to peer (shared Key)" is selected, that is the desired behavior since they make no sense in a peer to peer environment. Whether they are hidden or not, the values are ignored so it really makes no difference.

What about force all traffic trough gateway? This is also hidden in shared key peer2peer.
Are you sure local networks on SERVER pae should be hidden?

maverick_slo

Here we go, configs attached.

SHARED226.txt
SHARED230.txt
TLS226.txt
TLS230.txt