Routing PIA VPN to select devices on LAN

mauroman33

I solved the DNS leak enabling the DNS resolver and placing in the LAN tab the following rules

![DNS leak rules.png](/public/imported_attachments/1/DNS leak rules.png)
![DNS leak rules.png_thumb](/public/imported_attachments/1/DNS leak rules.png_thumb)

cobrahead

@mauroman33:

I solved the DNS leak enabling the DNS resolver and placing in the LAN tab the following rules

How do you enable the DNS resolver? Are you creating another rule from the Firewall->Rules->LAN page? Are both of the rules in your screen shot at the bottom of the list?

My rules page is attached. I don't have any rules relating to DNS Allow/Block.

firewall_rules.png_thumb

johnpoz

What do you think is leaking?? Yeah if you ask pfsense for dns, and it resolves it or even forwards it which is what it is designed to do..

If you do not want your IPs to not talk to pfsense, or use the internet then create a rule.. How is this not clear?? with your rules you have posted.. If you set pfsense to ignore rules when gateway is down then than your traffic from your clients you want to use the vpn will just go to the next rule that says go out to internet via anyway pfsense is connected, its default route, etc. sure your can ask pfsense anything..

If you don't want they said clients to do that, then under the rule that sends them to vpn gateway create a rule that will trigger on their IPs that blocks what you do not want them to do.. If you don't want them to talk to anything then the rule would be block/reject dest any..

cobrahead

@johnpoz:

What do you think is leaking?? Yeah if you ask pfsense for dns, and it resolves it or even forwards it which is what it is designed to do..

If you do not want your IPs to not talk to pfsense, or use the internet then create a rule.. How is this not clear?? with your rules you have posted..

Sorry, I am clearly new to this, I have only been using pfsense for a week now.

When I am using the VPN connection with PIA and I check my IP it is showing an IP on the server I have chosen, Seattle WA in my case… but when I run the DNSleaktest it shows my local ISP address. Isn't that a DNS leak?

mauroman33

I'm sorry if my short answer may have made confusion.
Surely what is written by johnpoz is totally correct.
Going back to my answer, I activated the DNS resolver from Services->DNS Resolver->General Settings then I added the two previous rules in Firewall->Rules->LAN placing them immediately after the Anti-Lockout Rule.
This way I avoided that all devices on my network can use a DNS that is different from what was set in pfSense which is, in my case, the VPN provider's DNS because in System->General Setup I did not set any DNS.

cobrahead

@mauroman33:

I'm sorry if my short answer may have made confusion.
Surely what is written by johnpoz is totally correct.
Going back to my answer, I activated the DNS resolver from Services->DNS Resolver->General Settings then I added the two previous rules in Firewall->Rules->LAN placing them immediately after the Anti-Lockout Rule.
This way I avoided that all devices on my network can use a DNS that is different from what was set in pfSense which is, in my case, the VPN provider's DNS because in System->General Setup I did not set any DNS.

Cool. Would you mind posting those DNS rules 'edit' pages. Just want to make sure I am configuring them correctly. Thanks

Attached are mine, something isn't set right… still getting DNS leak.

firewall_rules.png_thumb
![dns_pass rule.png](/public/imported_attachments/1/dns_pass rule.png)
![dns_pass rule.png_thumb](/public/imported_attachments/1/dns_pass rule.png_thumb)

dns_block_rule.png_thumb
![services_dns resolver_general settings.png](/public/imported_attachments/1/services_dns resolver_general settings.png)
![services_dns resolver_general settings.png_thumb](/public/imported_attachments/1/services_dns resolver_general settings.png_thumb)

mauroman33

You're welcome.
Here it is.

![Allow DNS.png](/public/imported_attachments/1/Allow DNS.png)
![Allow DNS.png_thumb](/public/imported_attachments/1/Allow DNS.png_thumb)
![Block DNS.png](/public/imported_attachments/1/Block DNS.png)
![Block DNS.png_thumb](/public/imported_attachments/1/Block DNS.png_thumb)

cobrahead

@mauroman33:

You're welcome.
Here it is.

That's what I have. I edited my last post to include the screenshots. Not sure what I am missing.

mauroman33

You will have the same result even using a single rule.

Does it work for you?

https://dnsleaktest.com/

DNS.png_thumb

mauroman33

@cobrahead:

@mauroman33:

You're welcome.
Here it is.

That's what I have. I edited my last post to include the screenshots. Not sure what I am missing.

I don't see anything strange.
Here the other settings in my system.

General_Setup.png_thumb

DHCP_Server.png_thumb

cobrahead

@mauroman33:

You will have the same result even using a single rule.

Does it work for you?

https://dnsleaktest.com/

No. I tried changing the destination to 'Invert Match' and 'LAN Address' … same results on dnsleaktest... it comes up with my ISP.

After making these changes should I only use this rule and get rid of the DNS Allow rule?

cobrahead

@mauroman33:

Here the other settings in my system.

OK. So I went to Services -> DNS Resolver -> General Settings and changed the Outgoing Network Interface from ANY to OPENVPN and that was what I missed. DNSleak stopped… at least according to dnsleaktest.com

Thanks for your help!

mauroman33

@cobrahead:

@mauroman33:

You will have the same result even using a single rule.

Does it work for you?

https://dnsleaktest.com/

No. I tried changing the destination to 'Invert Match' and 'LAN Address' … same results on dnsleaktest... it comes up with my ISP.

After making these changes should I only use this rule and get rid of the DNS Allow rule?

Yes, it's up to you choose if you want to reach te same goal using the two previos rules or only the last one.

mauroman33

Fine.
Just a note: if you want to avoid using a DNS (eg the one of the ISP) these rules are just a precaution to prevent anyone from doing so by manually changing the DNS of the device connected to the LAN.
If you have set the DNS resolver, when you're connected to the VPN provider, the dnsleaktest should show the IP address of the VPN.

cobrahead

Got it. I have learned a lot over the last week. :D

The only thing that is not working now is stopping and re-starting the OpenVPN service. Some change(s) I made today have caused a full reboot to be necessary in order to restart OpenVPN if it goes down.

mauroman33

You could try to install Service_Watchdog from System->Package Manager->Available Packages

Then in Services->Service Watchdog->Add you can select the OpenVPN client that you're using

cobrahead

@mauroman33:

You could try to install Service_Watchdog from System->Package Manager->Available Packages

Then in Services->Service Watchdog->Add you can select the OpenVPN client that you're using

I added it and set it up. No luck though. When I manually stop OpenVPN I cannot get it to restart, without rebooting pfSense.

mauroman33

After a failed attempt, did you try to check on Status-> System Logs-> OpenVPN?

cobrahead

@mauroman33:

After a failed attempt, did you try to check on Status-> System Logs-> OpenVPN?

This is what I get after I manually shut it down and try to re-start it.

Aug 16 16:55:11 openvpn 29537 RESOLVE: Cannot resolve host address: swiss.privateinternetaccess.com: hostname nor servname provided, or not known

mauroman33

It seems there is a problem with DNS.
Sometimes it happened in my system also, so I added the unbound service in Service Watchdog and the problem has not more occurred.
Actually right now there is only the unbound service in my Service Watchdog.