Ntopng development

MikeV7896

Version 0.8.4_1 with HTTPS support is rolling out now.

Is this package update version 2.4 of ntopng, or still the previous version?

dennypage

It's the same version of ntopng, with the addition of support for HTTPS in the pfSense package.

Cino

I found bug with the ssl version. You may want to remove "\n" from the new code.


	if ($config['system']['webgui']['protocol'] == "https") {
		$cert =& lookup_cert($config['system']['webgui']['ssl-certref']);
		ntopng_write_cert_file("/usr/local/share/ntopng/httpdocs/ssl/ntopng-cert.pem", $cert);
		$http_args = "-w 0 -W 3000\n";
	} else {
		unlink_if_exists("/usr/local/share/ntopng/httpdocs/ssl/ntopng-cert.pem");
		$http_args = "-w 3000\n";
	}

It created the the startup file incorrectly


rc_start() {
		/usr/local/bin/redis-server --dir /var/db/ntopng/ --dbfilename ntopng.rdb &
	/usr/local/bin/ntopng -d /var/db/ntopng -G /var/run/ntopng.pid -s -e -w 0 -W 3000
    -i 'em2' --dns-mode '0'  --local-networks 'fe80::/10,192.168.0.0/24,2000:0000:0000:2400::/64' &

dennypage

@Cino:

I found bug with the ssl version. You may want to remove "\n" from the new code.

You are quite correct. Not sure how I missed that in testing.

PR created.

Thanks

garyd9

dennypage, is there some trick to getting someone to accept pull requests? I submitted one a couple weeks ago to add ipv6 addresses to "local-networks" in the ntopng command line, but it's gone idle as far as I can see…

(I'm just trying to figure out if I missed a step in the submission or not.)

Thanks
Gary

dennypage

@garyd9:

dennypage, is there some trick to getting someone to accept pull requests? I submitted one a couple weeks ago to add ipv6 addresses to "local-networks" in the ntopng command line, but it's gone idle as far as I can see…

No special trick, but I went to look for your PR and couldn't find it. What is the PR number?

garyd9

@dennypage:

No special trick, but I went to look for your PR and couldn't find it. What is the PR number?

https://github.com/pfsense/pfsense-packages/pull/1262

dennypage

I believe you want this repo here:

https://github.com/pfsense/FreeBSD-ports

which corresponds to packages in pfSense 2.3 and later.

Look in net/pfSense-pkg-ntopng.

garyd9

@dennypage:

I believe you want this repo here:

https://github.com/pfsense/FreeBSD-ports

which corresponds to packages in pfSense 2.3 and later.

Look in net/pfSense-pkg-ntopng.

Okay, thank you. I'll redo my patch tomorrow morning in that other repo.

r_e_d_b_a_r_o_n

@dennypage:

@Cino:

I found bug with the ssl version. You may want to remove "\n" from the new code.

You are quite correct. Not sure how I missed that in testing.

PR created.

Thanks

Hello, I updated ntopng package to 0.8.4_2. From changelog it fixes problem with \n in startup script. BUT after upgrade still same config and startup file is generated. Edited it manually, removed newline but still not starting with error : "[HTTPserver.cpp:503] ERROR: Unable to start HTTP server (IPv4) on ports 3000s: Invalid argument". It only started after removing -W argument (HTTPS).
New bug or my problem?

Modified ntopng.sh

rc_start() {
/usr/local/bin/redis-server –dir /var/db/ntopng/ --dbfilename ntopng.rdb &
/usr/local/bin/ntopng -d /var/db/ntopng -G /var/run/ntopng.pid -s -e -w 0 -W 3000 -i 'vmx1' -i 'vmx2' --dns-mode '0' --local-networks '192.168.0.0/16,172.16.0.0/12,10.0.0.0/8' &

}

dennypage

If you are using HTTPS enabled in the pfSense gui, you will need to visit the ntopng settings page (Diagnostics / ntopng Settings) and press save. This will cause the certificate to be set up in order to use HTTPS with ntopng.

luckman212

@dennypage:

It's the same version of ntopng, with the addition of support for HTTPS in the pfSense package.

Denny, do you know what the main reason is that the 2.4 version of ntopng isn't available in pfSense? I see the FreeBSD port has been ready for some time…
https://github.com/freebsd/freebsd-ports/blob/master/net/ntopng/Makefile

kesawi

I've just upgraded to ntopng 0.8.4_2 on pfSense 2.3.2 and get the following error message in the System Log:

ntopng 		[HTTPserver.cpp:503] ERROR: Unable to start HTTP server (IPv4) on ports 3000s: Invalid argument

The ntopng service is showing as stopped in the service status and the ntopng process isn't running (ie not appearing when I run ps aux or sockstat.

I've tried uninstalling, reinstalling, and unchecking the "Keep Data/Settings" options, but my settings seem to be kept, and the error remains. I've tried changing the settings in the GUI and re-saving as suggested a couple of posts up.

I do have a certificate (ntopng-cert.pem) in /usr/local/share/ntopng/httpdocs/ssl which gets regenerated each time I update the settings through the GUI.

dennypage

Would you mind checking the sum on ntopng.inc please?

The command is this: sum /usr/local/pkg/ntopng.inc

The expected output is this: 51966 12 /usr/local/pkg/ntopng.inc

Thanks

dennypage

@luckman212:

Denny, do you know what the main reason is that the 2.4 version of ntopng isn't available in pfSense?

I don't have direct knowledge, but if I had to guess I would say that it's a fair bit of work and nobody has volunteered or been assigned for it.

luckman212

Hmm ok I didn't realize it was much work after the FreeBSD port. Ok, I wish I could help somehow. I looked at the "Developing Packages" page but tbh I wouldn't know where to start :(

r_e_d_b_a_r_o_n

@dennypage:

Would you mind checking the sum on ntopng.inc please?

The command is this: sum /usr/local/pkg/ntopng.inc

The expected output is this: 51966 12 /usr/local/pkg/ntopng.inc

Thanks

This is output of sum:

51966 12 /usr/local/pkg/ntopng.inc

As kesawi mention I also have certificate at place and it's regenerating.

dennypage

Regeneration of the ssl certificate every time you save settings or reboot is expected.

r_e_d_b_a_r_o_n, can you post the unmodified content of /usr/local/etc/rc.d/ntopng.sh please?

And can you clarify the version of pfSense you are running as well?

Thanks

r_e_d_b_a_r_o_n

@dennypage:

Regeneration of the ssl certificate every time you save settings or reboot is expected.

r_e_d_b_a_r_o_n, can you post the unmodified content of /usr/local/etc/rc.d/ntopng.sh please?

And can you clarify the version of pfSense you are running as well?

Thanks

So I uninstalled package and checked that every file belonging to ntopng is deleted and reinstalled;

Output from sum is: 59748 12 /usr/local/pkg/ntopng.inc (so previosly file was modified by me);

ntopng-cert.pem is avalable in /usr/local/share/ntopng/httpdocs/ssl;

Contents of /usr/local/etc/rc.d/ntopng.sh:
#!/bin/sh

This file was automatically generated

by the pfSense service handler.

rc_start() {
/usr/local/bin/redis-server –dir /var/db/ntopng/ --dbfilename ntopng.rdb &
/usr/local/bin/ntopng -d /var/db/ntopng -G /var/run/ntopng.pid -s -e -w 0 -W 3000
-i 'vmx1' -i 'vmx2' --dns-mode '0' --local-networks '192.168.0.0/16,172.16.0.0/12,10.0.0.0/8' &

}

rc_stop() {
/usr/bin/killall ntopng redis-cli redis-server

}

case $1 in
start)
rc_start
;;
stop)
rc_stop
;;
restart)
rc_stop
rc_start
;;
esac

pfSense vewrsion I am running is:

2.3.2-RELEASE (amd64)
built on Tue Jul 19 12:44:43 CDT 2016
FreeBSD 10.3-RELEASE-p5

kesawi

@dennypage:

Would you mind checking the sum on ntopng.inc please?

The command is this: sum /usr/local/pkg/ntopng.inc

The expected output is this: 51966 12 /usr/local/pkg/ntopng.inc

My output is different:

59748 12 /usr/local/pkg/ntopng.inc

Also my /usr/local/etc/rc.d/ntopng.sh:

#!/bin/sh
# This file was automatically generated
# by the pfSense service handler.

rc_start() {
                /usr/local/bin/redis-server --dir /var/db/ntopng/ --dbfilename ntopng.rdb &
        /usr/local/bin/ntopng -d /var/db/ntopng -G /var/run/ntopng.pid -s -e -w 0 -W 3000
 -H   -i 'lagg0_vlan2' --dns-mode '0'  --local-networks '192.168.0.0/16,172.16.0.0/12,10.0.0.0/8' &

}

rc_stop() {
        /usr/bin/killall ntopng redis-cli redis-server

}

case $1 in
        start)
                rc_start
                ;;
        stop)
                rc_stop
                ;;
esac

I notice I have -H in the rc_start.

When I manually launch ntopng.sh

 /usr/local/etc/rc.d/ntopng.sh start
                _._
           _.-``__ ''-._
      _.-``    `.  `_.  ''-._           Redis 3.0.7 (00000000/0) 64 bit
  .-`` .-```.  ```\/    _.,_ ''-._
 (    '      ,       .-`  | `,    )     Running in standalone mode
 |`-._`-...-` __...-.``-._|'` _.-'|     Port: 6379
 |    `-._   `._    /     _.-'    |     PID: 13809
  `-._    `-._  `-./  _.-'    _.-'
 |`-._`-._    `-.__.-'    _.-'_.-'|
 |    `-._`-._        _.-'_.-'    |           http://redis.io
  `-._    `-._`-.__.-'_.-'    _.-'
 |`-._`-._    `-.__.-'    _.-'_.-'|
 |    `-._`-._        _.-'_.-'    |
  `-._    `-._`-.__.-'_.-'    _.-'
      `-._    `-.__.-'    _.-'
          `-._        _.-'
              `-.__.-'

13809:M 05 Sep 06:32:26.174 # Server started, Redis version 3.0.7
13809:M 05 Sep 06:32:26.180 * DB loaded from disk: 0.006 seconds
13809:M 05 Sep 06:32:26.180 * The server is now ready to accept connections on port 6379
05/Sep/2016 06:32:26 [Prefs.cpp:915] Logging into /var/db/ntopng/ntopng.log
05/Sep/2016 06:32:26 [Ntop.cpp:1013] Setting local networks to 127.0.0.0/8
05/Sep/2016 06:32:26 [Redis.cpp:92] Successfully connected to redis 127.0.0.1:6379@0
05/Sep/2016 06:32:26 [Ntop.cpp:987] Parent process is exiting (this is normal)
/usr/local/etc/rc.d/ntopng.sh: -H: not found

I modified ntopng.sh to remove the line break before the -H and then ran it manually, and the script started without error, but still received [HTTPserver.cpp:503] ERROR in the log files.