Guest LAN cannot access internet

WesleysHuman

What are your outbound NAT Settings? Set to Automatic? If not, is your subnet included in the rules you've written?

What are your DNS Resolver settings? Have you selected All network interfaces, if not have you included OPT1?

What are your settings under Interfaces / OPT1?

What is the output for OPT1 under Status / Interfaces?

Outbound NAT is automatic

DNS Resolver is set to All on the network interfaces

OPT1 is static with the addresses listed before (192.168.25.1/24 & fd6d:d21f:890b:547:25::1/80), MTU/MSS defaults, reserved networks unchecked

Status: up
MAC Address: 0c:c4:7a:45:e2:c2 - Super Micro Computer
IPv4 Address: 192.168.25.1
Subnet mask IPv4: 255.255.255.0
IPv6 Link Local: fe80::ec4:7aff:fe45:e2c2%igb2
IPv6 Address: fd6d:d21f:890b:547:25::1
Subnet mask IPv6: 80
MTU: 1500
Media: 100baseTX <full-duplex>In/out packets: 43654/180308 (2.97 MiB/25.77 MiB)
In/out packets (pass): 43654/180308 (2.97 MiB/25.77 MiB)
In/out packets (block): 521875/0 (38.65 MiB/0 B)
In/out errors: 0/0
Collisions: 0</full-duplex>

WesleysHuman

@Derelict:

In addition, a client that gets what looks like a valid IPv6 configuration is generally going to try to do everything via IPv6 before falling back to IPv4 (if you're lucky - pretty much up to the client what it does in that case.)

I don't know what you're trying to do with those ULA addresses but you might try just setting IPv6 to None on OPT1 and getting IPv4 working first.

And after IPv4 is working there is no reason to mess around like that when www.tunnelbroker.net is so generous. Just get a /48 from them and set up a GIF tunnel.

https://doc.pfsense.org/index.php/Using_IPv6_with_a_Tunnel_Broker

I have disabled IPv6 for now as you suggested.

Derelict

Did it fix your issue?

WesleysHuman

Negative.

pfBasic

I'm pretty new to all of this myself, but all of your settings look like they should work great.

I'm assuming no upstream gateway on your interface?

Anything helpful in the system logs?

Have you tried using a different client on the network to see if the client is the issue?

WesleysHuman

@pfBasic:

I'm pretty new to all of this myself, but all of your settings look like they should work great.

I'm assuming no upstream gateway on your interface?

Anything helpful in the system logs?

Have you tried using a different client on the network to see if the client is the issue?

Nothing upstream on my equipment.

I haven't looked in the logs so I'll check there.

I've tried different OSs on the same system without any luck. I was initially concerned about some kind of virus on the system.

pfBasic

Can you connect any other device to the network and test it?

It could be a hardware issue on the client you're using.

johnpoz

So this client can ping pfsense opt1 interface IP 192.168.25.1 ?? If he could then dns wouldn't fail, since your just asking pfsense for dns which has zero to do with going anywhere other than talking to pfsense. The default out of the box is resolver listening on all interfaces..

You sure your getting the correct IP and gateway? And that you can ping pfsense? And that your automatic outbound nat now includes your 192.168.25/24 network

WesleysHuman

The issue has been fixed. When I tried pinging the firewall from the one host all packets were lost. I went back searching and found a post saying that allowing access to the wan net would not allow access to the whole internet. I then changed my rules as follows:

1. Deny access from opt1 to lan
2. Deny access from opt1 to opt2
3. Allow access from opt1 to all

Thank you for your help!

2017-02-22_04-18-57.png_thumb

Derelict

That's pretty much what you posted in your first post. So that wasn't what was wrong. It was something else.

johnpoz

No real difference in those rules - your last rule is an any any.. So either you didn't post up what your rules actually were the first time, or yeah something else.