Selective Remote Access
-
In the status firewall logs when I try to access a web site it creates a default block on the WAN port. I guessing this means there was no rule above it that allowed the traffic to pass thru the WAN.
Yes, that's it means. But the log entries which matter here are on the PLEX2 interface not on WAN.
You may use the filter option in the GUI to get less noise.Is it correct that any rules I create to pass this traffic should be the 172.16.2.0/24 Virtual address vs the Real Address listed on the openvpn status page?
Yes, the source address is the clients tunnel IP.
-
I disabled all the block rules on the WAN, Plex2, and OpenVPN interfaces including Bogons and RFC 1918 networks but still can't access the internet with the VPN on. Am I correct that it must not be a blocked problem. I'm missing a pass command for the traffic?
-
Are the routes on the client set correctly?
Please post the clients routing table. -
Are the routes on the client set correctly?
Please post the clients routing table.Here is the output of the diagnostic/routes :opvns4 is the Plex2 VPN
IPv4 Routes Destination Gateway Flags Use Mtu Netif Expire 0.0.0.0/1 172.21.92.1 UGS 137 1500 ovpnc1 default x.x.x.1 UGS 18 1500 em3 81.171.110.67/32 x.x.x.1 UGS 169422 1500 em3 x.x.x.0/24 link#4 U 99628 1500 em3 x.x.x.x link#4 UHS 0 16384 lo0 127.0.0.1 link#9 UH 676122 16384 lo0 128.0.0.0/1 172.21.92.1 UGS 18201 1500 ovpnc1 172.16.2.0/24 172.16.2.2 UGS 5139 1500 ovpns4 172.16.2.1 link#14 UHS 199412 16384 lo0 172.16.2.2 link#14 UH 0 1500 ovpns4 172.21.92.0/23 172.21.92.1 UGS 0 1500 ovpnc1 172.21.92.1 link#15 UH 99536 1500 ovpnc1 172.21.92.42 link#15 UHS 0 16384 lo0 192.168.0.0/24 link#3 U 0 1500 em2 192.168.0.1 link#3 UHS 0 16384 lo0 192.168.1.0/24 link#1 U 32974135 1500 em0 192.168.1.1 link#1 UHS 0 16384 lo0 192.168.10.0/24 link#10 U 0 1500 em2_vlan10 192.168.10.1 link#10 UHS 0 16384 lo0 192.168.20.0/24 link#11 U 0 1500 em2_vlan20 192.168.20.1 link#11 UHS 0 16384 lo0 192.168.30.0/24 link#12 U 0 1500 em2_vlan30 192.168.30.1 link#12 UHS 0 16384 lo0 192.168.40.0/24 link#13 U 0 1500 em2_vlan40 192.168.40.1 link#13 UHS 0 16384 lo0 192.168.60.0/24 link#2 U 35513 1500 em1 192.168.60.1 link#2 UHS 0 16384 lo0
and the openvpn status routing table
![Routing Table.jpg](/public/imported_attachments/1/Routing Table.jpg)
![Routing Table.jpg_thumb](/public/imported_attachments/1/Routing Table.jpg_thumb) -
I asked for the routing table of the clients computer.
-
Sorry. I use my iphone. Any tips on how to get it from the openvpn app?
-
Don't know.
Check if you're able to access a public hosts by its IP address. Maybe the iPhone just can't access the DNS while vpn is connected.
On pfSense you can do packet capture (Diagnostic menu) while you're trying to access a internet IP to check if the traffic is routed over the vpn.
To do so, select the PLEX2 interface, to avoid noise you can select a particular protocol and port. At host enter the destination IP and start the capture. Then try to access the destination IP with the iphon. Stop the capture to see the result.
If you can see packets, select the WAN interface and repeat the capture.
Post the results, please. -
Check if you're able to access a public hosts by its IP address. Maybe the iPhone just can't access the DNS while vpn is connected.
https://81.171.110.67/ is the IP that is in the packet capture and I can't get to that site on my windows browser (nothing happens). Googling apple.com IP gives https://81.171.110.52/
which also doesn't connect but apple.com does. On iPhone I get forbidden error, you do not have permission to access this serverOn pfSense you can do packet capture (Diagnostic menu) while you're trying to access a internet IP to check if the traffic is routed over the vpn.
To do so, select the PLEX2 interface, to avoid noise you can select a particular protocol and port. At host enter the destination IP and start the capture. Then try to access the destination IP with the iphon. Stop the capture to see the result.
If you can see packets, select the WAN interface and repeat the capture.
Post the results, please.WAN IP capture
15:48:34.274662 IP 81.171.110.67.1194 > x.x.x.x.30054: UDP, length 177 15:48:34.275654 IP x.x.x.x.30054 > 81.171.110.67.1194: UDP, length 113 15:48:34.275693 IP x.x.x.x.30054 > 81.171.110.67.1194: UDP, length 209 15:48:34.275717 IP x.x.x.x.30054 > 81.171.110.67.1194: UDP, length 273 15:48:34.283405 IP 81.171.110.67.1194 > x.x.x.x.30054: UDP, length 113 15:48:34.283528 IP 81.171.110.67.1194 > x.x.x.x.30054: UDP, length 129 15:48:34.283737 IP x.x.x.x.30054 > 81.171.110.67.1194: UDP, length 97 15:48:34.283781 IP x.x.x.x.30054 > 81.171.110.67.1194: UDP, length 609 15:48:34.291524 IP 81.171.110.67.1194 > x.x.x.x.30054: UDP, length 97 15:48:34.292272 IP 81.171.110.67.1194 > x.x.x.x.30054: UDP, length 257 15:48:34.292602 IP x.x.x.x.30054 > 81.171.110.67.1194: UDP, length 161 15:48:34.293847 IP x.x.x.x.30054 > 81.171.110.67.1194: UDP, length 161 15:48:34.293875 IP x.x.x.x.30054 > 81.171.110.67.1194: UDP, length 161 15:48:34.293904 IP x.x.x.x.30054 > 81.171.110.67.1194: UDP, length 145 15:48:34.297145 IP 81.171.110.67.1194 > x.x.x.x.30054: UDP, length 241 15:48:34.298144 IP 81.171.110.67.1194 > x.x.x.x.30054: UDP, length 177 15:48:34.298473 IP x.x.x.x.30054 > 81.171.110.67.1194: UDP, length 145 15:48:34.302017 IP 81.171.110.67.1194 > x.x.x.x.30054: UDP, length 97 15:48:34.302025 IP 81.171.110.67.1194 > x.x.x.x.30054: UDP, length 145 15:48:34.322702 IP x.x.x.x.30054 > 81.171.110.67.1194: UDP, length 129 15:48:34.342695 IP x.x.x.x.30054 > 81.171.110.67.1194: UDP, length 97 15:48:34.345616 IP 81.171.110.67.1194 > x.x.x.x.30054: UDP, length 97 15:48:34.452554 IP x.x.x.x.30054 > 81.171.110.67.1194: UDP, length 97 15:48:34.456553 IP 81.171.110.67.1194 > x.x.x.x.30054: UDP, length 97 15:48:34.953592 IP x.x.x.x.30054 > 81.171.110.67.1194: UDP, length 97 15:48:34.960886 IP 81.171.110.67.1194 > x.x.x.x.30054: UDP, length 97 15:48:35.454624 IP x.x.x.x.30054 > 81.171.110.67.1194: UDP, length 97 15:48:35.461223 IP 81.171.110.67.1194 > x.x.x.x.30054: UDP, length 97 15:48:35.960584 IP x.x.x.x.30054 > 81.171.110.67.1194: UDP, length 97 15:48:35.965556 IP 81.171.110.67.1194 > x.x.x.x.30054: UDP, length 97 15:48:36.461627 IP x.x.x.x.30054 > 81.171.110.67.1194: UDP, length 97 15:48:36.465892 IP 81.171.110.67.1194 > x.x.x.x.30054: UDP, length 97 15:48:36.895894 IP 81.171.110.67.1194 > x.x.x.x.30054: UDP, length 129 15:48:36.922474 IP x.x.x.x.30054 > 81.171.110.67.1194: UDP, length 129 15:48:36.962547 IP x.x.x.x.30054 > 81.171.110.67.1194: UDP, length 97 15:48:36.970350 IP 81.171.110.67.1194 > x.x.x.x.30054: UDP, length 97 15:48:37.464638 IP x.x.x.x.30054 > 81.171.110.67.1194: UDP, length 97 15:48:37.470561 IP 81.171.110.67.1194 > x.x.x.x.30054: UDP, length 97 15:48:37.966576 IP x.x.x.x.30054 > 81.171.110.67.1194: UDP, length 97 15:48:37.971022 IP 81.171.110.67.1194 > x.x.x.x.30054: UDP, length 97 15:48:38.468652 IP x.x.x.x.30054 > 81.171.110.67.1194: UDP, length 97 15:48:38.474981 IP 81.171.110.67.1194 > x.x.x.x.30054: UDP, length 97 15:48:38.969589 IP x.x.x.x.30054 > 81.171.110.67.1194: UDP, length 97 15:48:38.973443 IP 81.171.110.67.1194 > x.x.x.x.30054: UDP, length 129 15:48:38.973790 IP x.x.x.x.30054 > 81.171.110.67.1194: UDP, length 145 15:48:38.976065 IP 81.171.110.67.1194 > x.x.x.x.30054: UDP, length 97 15:48:38.986435 IP 81.171.110.67.1194 > x.x.x.x.30054: UDP, length 97 15:48:39.470586 IP x.x.x.x.30054 > 81.171.110.67.1194: UDP, length 97 15:48:39.475903 IP 81.171.110.67.1194 > x.x.x.x.30054: UDP, length 97 15:48:39.972605 IP x.x.x.x.30054 > 81.171.110.67.1194: UDP, length 97 15:48:39.980111 IP 81.171.110.67.1194 > x.x.x.x.30054: UDP, length 97 15:48:40.203479 IP x.x.x.x.30054 > 81.171.110.67.1194: UDP, length 353 15:48:40.203510 IP x.x.x.x.30054 > 81.171.110.67.1194: UDP, length 145 15:48:40.209728 IP 81.171.110.67.1194 > x.x.x.x.30054: UDP, length 97 15:48:40.209852 IP 81.171.110.67.1194 > x.x.x.x.30054: UDP, length 145 15:48:40.250434 IP x.x.x.x.30054 > 81.171.110.67.1194: UDP, length 97 15:48:40.365267 IP 81.171.110.67.1194 > x.x.x.x.30054: UDP, length 689 15:48:40.365275 IP 81.171.110.67.1194 > x.x.x.x.30054: UDP, length 145 15:48:40.365611 IP x.x.x.x.30054 > 81.171.110.67.1194: UDP, length 97 15:48:40.473600 IP x.x.x.x.30054 > 81.171.110.67.1194: UDP, length 97 15:48:40.480572 IP 81.171.110.67.1194 > x.x.x.x.30054: UDP, length 97 15:48:40.578933 IP x.x.x.x.30054 > 81.171.110.67.1194: UDP, length 145 15:48:40.578950 IP x.x.x.x.30054 > 81.171.110.67.1194: UDP, length 145 15:48:40.578965 IP x.x.x.x.30054 > 81.171.110.67.1194: UDP, length 145 15:48:40.578980 IP x.x.x.x.30054 > 81.171.110.67.1194: UDP, length 145 15:48:40.586261 IP 81.171.110.67.1194 > x.x.x.x.30054: UDP, length 161 15:48:40.586506 IP x.x.x.x.30054 > 81.171.110.67.1194: UDP, length 145 15:48:40.587884 IP 81.171.110.67.1194 > x.x.x.x.30054: UDP, length 225 15:48:40.588119 IP x.x.x.x.30054 > 81.171.110.67.1194: UDP, length 145 15:48:40.637106 IP 81.171.110.67.1194 > x.x.x.x.30054: UDP, length 225 15:48:40.647512 IP x.x.x.x.30054 > 81.171.110.67.1194: UDP, length 145 15:48:40.647559 IP x.x.x.x.30054 > 81.171.110.67.1194: UDP, length 145 15:48:40.656345 IP 81.171.110.67.1194 > x.x.x.x.30054: UDP, length 161 15:48:40.674960 IP 81.171.110.67.1194 > x.x.x.x.30054: UDP, length 177 15:48:40.679560 IP x.x.x.x.30054 > 81.171.110.67.1194: UDP, length 145 15:48:40.730177 IP 81.171.110.67.1194 > x.x.x.x.30054: UDP, length 225 15:48:40.737581 IP x.x.x.x.30054 > 81.171.110.67.1194: UDP, length 145 15:48:40.737631 IP x.x.x.x.30054 > 81.171.110.67.1194: UDP, length 145 15:48:40.746043 IP 81.171.110.67.1194 > x.x.x.x.30054: UDP, length 161 15:48:40.786647 IP 81.171.110.67.1194 > x.x.x.x.30054: UDP, length 161 15:48:40.786811 IP x.x.x.x.30054 > 81.171.110.67.1194: UDP, length 145 15:48:40.821500 IP 81.171.110.67.1194 > x.x.x.x.30054: UDP, length 177 15:48:40.821640 IP x.x.x.x.30054 > 81.171.110.67.1194: UDP, length 129 15:48:40.826996 IP 81.171.110.67.1194 > x.x.x.x.30054: UDP, length 145 15:48:40.846111 IP 81.171.110.67.1194 > x.x.x.x.30054: UDP, length 225 15:48:40.855365 IP x.x.x.x.30054 > 81.171.110.67.1194: UDP, length 129 15:48:40.862065 IP x.x.x.x.30054 > 81.171.110.67.1194: UDP, length 129 15:48:40.874189 IP x.x.x.x.30054 > 81.171.110.67.1194: UDP, length 129 15:48:40.874248 IP x.x.x.x.30054 > 81.171.110.67.1194: UDP, length 113 15:48:40.892584 IP 81.171.110.67.1194 > x.x.x.x.30054: UDP, length 177 15:48:40.895565 IP x.x.x.x.30054 > 81.171.110.67.1194: UDP, length 145 15:48:40.924940 IP 81.171.110.67.1194 > x.x.x.x.30054: UDP, length 225 15:48:40.975709 IP x.x.x.x.30054 > 81.171.110.67.1194: UDP, length 97 15:48:40.981283 IP 81.171.110.67.1194 > x.x.x.x.30054: UDP, length 97 15:48:41.004573 IP x.x.x.x.30054 > 81.171.110.67.1194: UDP, length 145 15:48:41.067360 IP 81.171.110.67.1194 > x.x.x.x.30054: UDP, length 225 15:48:41.097216 IP 81.171.110.67.1194 > x.x.x.x.30054: UDP, length 225 15:48:41.476634 IP x.x.x.x.30054 > 81.171.110.67.1194: UDP, length 97 15:48:41.481368 IP 81.171.110.67.1194 > x.x.x.x.30054: UDP, length 97 15:48:41.977559 IP x.x.x.x.30054 > 81.171.110.67.1194: UDP, length 97
Plex2 Capture Host address gives nothing without it gives
16:04:02.925538 IP 172.16.2.248.55794 > 192.168.1.149.80: tcp 0 16:04:03.901359 IP 172.16.2.248.55794 > 192.168.1.149.80: tcp 0 16:04:04.909655 IP 172.16.2.248.55794 > 192.168.1.149.80: tcp 0 16:04:05.781252 IP 172.16.2.248.55376 > 208.67.222.222.53: UDP, length 42 16:04:05.933556 IP 172.16.2.248.55794 > 192.168.1.149.80: tcp 0 16:04:07.790472 IP 172.16.2.248.55376 > 208.67.222.222.53: UDP, length 42 16:04:11.782673 IP 172.16.2.248.55376 > 208.67.220.220.53: UDP, length 42
Why is 81.171.110.67.1194 on my WAN and not 81.171.110.67.1195 as my VPN sever in on port 1195?
My settings for Plex2 Capture
![Plex2 Capture Settings.jpg](/public/imported_attachments/1/Plex2 Capture Settings.jpg)
![Plex2 Capture Settings.jpg_thumb](/public/imported_attachments/1/Plex2 Capture Settings.jpg_thumb) -
https://81.171.110.67/ is the IP that is in the packet capture and I can't get to that site on my windows browser (nothing happens). Googling apple.com IP gives https://81.171.110.52/
which also doesn't connect but apple.com does. On iPhone I get forbidden error, you do not have permission to access this server???
Resolving apple.com gives me 17.142.160.59
81.171.110.67 seems to be your own public IP. The WAN capture shows a connection to port 1194.
You're running multiple vpn servers. So this might be a connection to another server.This capture is cannot help to resolve the issue in any way.
-
I have a VPN client running to change my IP address. Didn't recognize the IP address. If I turn off the VPN client I can access the internet while connected to the remote VPN server. Is it possible to run the VPN Client and Remote VPN server and still access the internet? Sorry for the confusion I didn't realize it was an issue.
-
Yes, that's possible. But you've to clarify how the upstream traffic from PLEX2 should be routed out. To the VPN server or to the WAN gateway.
Now, since you haven't specified a gateway in the firewall rule, the traffic is routed to the vpn server. But since you haven't set an outbound NAT rule for this, you get no connection. -
Yes, that's possible. But you've to clarify how the upstream traffic from PLEX2 should be routed out. To the VPN server or to the WAN gateway.
Now, since you haven't specified a gateway in the firewall rule, the traffic is routed to the vpn server. But since you haven't set an outbound NAT rule for this, you get no connection.Thanks for hanging in there with me.
I created a rule on the PLEX2 interface, source =any, dst =any, and Gateway = WAN_DHCP Gateway then
Outbound rule- PLEX2 interface, protocol any, network 172.16.2.0/24, dst any, translation Interface Address.
Rebooted and doesn't work. Any idea on what I did incorrectly? -
Man, Outbound NAT rules have to be set on that interface where the packets go out!
So if you want to go out on WAN the interface has to be set to WAN.
The necessary rule was already set as shown in this post: https://forum.pfsense.org/index.php?topic=132341.msg729392#msg729392 -
Man, Outbound NAT rules have to be set on that interface where the packets go out!
So if you want to go out on WAN the interface has to be set to WAN.
The necessary rule was already set as shown in this post: https://forum.pfsense.org/index.php?topic=132341.msg729392#msg729392I have everything setup with the Plex2 rule having the WAN gateway but still packet capture still show trying to go out the 1194 client VPN instead of the WAN gateway. I even changed all 3 Plex2 rules to use the WAN gateway without success. If the WAN gateway is the default and the rule is set to use the default why does it need to be specified?
-
I've wrote above that you've to clarify where you want to route out the upstream traffic from PLEX2 client. If you haven't specified a gateway, the traffic is routed to the default gateway and this is obviously the vpn client if it's connected. So the packets are routed to the vpn client, but in fact you've no outbound NAT rule that, so the packets get dropped there, cause there is no route back for that source.
If you want the traffic route out to WAN while the vpn client is the default gateway, you've to specify the WAN gateway in the rule.
If you want to go out to the default gateway there's no need to specify a gateway in the rule, but you've to add an outbound NAT rule for that. -
I've wrote above that you've to clarify where you want to route out the upstream traffic from PLEX2 client. If you haven't specified a gateway, the traffic is routed to the default gateway and this is obviously the vpn client if it's connected. So the packets are routed to the vpn client, but in fact you've no outbound NAT rule that, so the packets get dropped there, cause there is no route back for that source.
If you want the traffic route out to WAN while the vpn client is the default gateway, you've to specify the WAN gateway in the rule.
If you want to go out to the default gateway there's no need to specify a gateway in the rule, but you've to add an outbound NAT rule for that.- I have specified the WAN gateway in the PLEX2 rule so have I satisfied the "you've to specify the WAN gateway in the rule"?
- If I have satisfied #1 then the problem is not specifying a outbound NAT rule. Can you give me an example of outbound rule that would work? There are not many options after Interface, Source address. Interface must be WAN, the Source is my 172.16.2.0/24 the VPN tunnel network, destination is any as it could be anywhere on the internet.
-
- I have specified the WAN gateway in the PLEX2 rule so have I satisfied the "you've to specify the WAN gateway in the rule"?
If you intend, that PLEX2 upstream traffic goes out on the WAN interface independently from the vpn client connection, that's okay.
- If I have satisfied #1 then the problem is not specifying a outbound NAT rule. Can you give me an example of outbound rule that would work? There are not many options after Interface, Source address. Interface must be WAN, the Source is my 172.16.2.0/24 the VPN tunnel network, destination is any as it could be anywhere on the internet.
Again, you've already set an outbound NAT rule for PLEX2 on WAN interface. The first rule shown in the picture here: https://forum.pfsense.org/index.php?topic=132341.msg729392#msg729392
Outbound NAT:
When a packet go out to WAN, the packets source address has to be translated to one of your public addresses, mostly the WAN (interface) address. Cause only public addresses are known in the internet, which is necessary to route back the responses to you.
So you have to set in the rule:
interface: WAN
source: here the tunnel subnet 172.16.2.0/24
All other options may be stay on their defaults. So the protocol and destination is any and the translation address is "interface address" which is your WAN address.Is this really as hard?
-
I have the outbound rule as, Intereface WAN, source 172.16.2.0/24 all other options at default.
If I have a rule on the Plex2 interface, source any, destination any, gateway default I can access my local LAN servers but not the internet. If I change the default gateway to the WAN I can access the internet but not any of the LAN servers.
-
If you intend, that PLEX2 upstream traffic goes out on the WAN interface independently from the vpn client connection, that's okay.
If I change the gateway on the Plex2 rule from WAN to default I can't get out to the internet. Not sure why default doesn't work but it still works with the gateway as WAN.
Had to add a path back to the LAN when I connect as the USER so I could access the other servers. All others in the Plex only alias can only connect to the Plex Server and internet through the WAN gateway.
Here is the final Plex2 rules. Thanks again for your help.
![Final Plex2.jpg](/public/imported_attachments/1/Final Plex2.jpg)
![Final Plex2.jpg_thumb](/public/imported_attachments/1/Final Plex2.jpg_thumb) -
If I change the gateway on the Plex2 rule from WAN to default I can't get out to the internet. Not sure why default doesn't work but it still works with the gateway as WAN.
I've mentioned that behaviour and the solution alreade twice.
here: https://forum.pfsense.org/index.php?topic=132341.msg733209#msg733209
and here: https://forum.pfsense.org/index.php?topic=132341.msg732814#msg732814So what are the troubles with that?
If your vpn client connection is up, the packets go out this connection, when there's no gateway specified in the appropriate rule. So you also need to add an outbound NAT rule for this traffic (on the vpn clients interface!). How to do, I've described here: https://forum.pfsense.org/index.php?topic=132341.msg733440#msg733440