pfSense 2.4.4-RELEASE-p1 is now available!
-
Ok - so I had tried to update my 4860 remote via vpn and it never came back.. Not sure exactly what happened... I am the first to say doing the update with all the packages and stuff I have running remote without some pre planning was not a good idea but pulling the trigger on both my 3100 remote installs went fine (no packages)..
So when I got home I could not log in via console either.. But a simple power cycle its up and running and have internet again..
As when you do this sort of update remote you should plan for issues is under statement.. My bad for sure - but a simple power cycle and all looks good. From what I can tell everything came back.. I will have to check logs and such - but as always you should follow the upgrade guidelines vs just clicking update.. Especially if device is remote..
As of now I have no idea why it hung on the reboot.. I might never know? But again - I have run into such problems with all kinds of of very expensive 10k per device units, etc.. So remote updates are always a roll of the device.. Remote update should always include someone that can power cycle and out of band console access sort of stuff..
But both of my 3100 clicky clicky - but they do not have all the packages my home box has installed..
All looks good - and yes I had grabbed a copy of config before update, and worse case which I knew I could do when I got home I have 2.4.4 media and copy of the config.. My pulling the trigger remote was a at worse a couple of hours down time before I got there..
I am just trying to be transparent on my experience.. This is for sure some sort of one off.. Prob related to my odd ball packages.. Something prob hung up the reboot..
Wife is calling dinner - so look at logs later.
-
@jimp I have reported this issue very early, but it has not been fixed. Please pay attention to this
https://forum.netgate.com/topic/135394/form-2-4-3-upgrade-2-4-4rc20180904-can-t-open-gateway-gui/37
-
@yon-0 said in pfSense 2.4.4-RELEASE-p1 is now available!:
@jimp I have reported this issue very early, but it has not been fixed. Please pay attention to this
https://forum.netgate.com/topic/135394/form-2-4-3-upgrade-2-4-4rc20180904-can-t-open-gateway-gui/37
See above, re: This is not a thread for reporting problems.
Also, that is not the same as what you stated. You said:
if you add ipv6 dns ip in DNS Server Settings, webgui will down
But the linked thread says it requires you to be using OCSP stapling, which narrows the issue significantly and explains why it's working for the majority of users.
-
Installed on SG-2220 from pfsense 2.4.3p1 - all working here.
Running packages: Snort, Squid
Thanks netgate!!! -
I performed the 2.4.4-RELEASE-p1 Update remotely today for my three SG-3100 in production, everything worked very smooth.
Two devices coming from 2.4.4 and one from 2.4.3-p1
Going for my two XG-7100 right after XMAS....way too much traffic on there 24/7 atm.
Thanks to the whole Netgate Team!-Rico
-
ran a online update and all seems good.
I came from 2.4.2
Nice to dhcp6 status screen fixed
Nice to see I no longer need my custom patch for ntp status screen as base pfsense now allows it to wotih global noquery set.
Nice to see my patch no longer needed for queue status screen refresh as base pfsense implemented custom refresh interval.Cpu utilisation is notably down I assume from the faster php 7.2.
Also nice that unbound got updated, I was going to put a request in for it but was done anyway.
-
The "2.4.4-RELEASE-p2" thread is locked so I had to ask here: 2.4.4-p2 is still not available at https://www.pfsense.org/download/. I find this very unusual. When will 2.4.4-p2 be available for fresh install? Is there any issue with the fresh install? I upgraded without any issues on multiple machines. Thanks!
-
This isn't the place to ask that, but I'll answer anyhow. We do not typically make CE installers for patch releases. -p1 was special because it had fixes for the installer that were needed for a large number of people.
There won't be published -p2 installers, install -p1 and upgrade.
-
one off installs for patches, p1, p2, p3, etc. etc. have never normal with pfsense. The release image, and then it updates to patches have been the normal since I can remember..
That they released a p1 image would yeah mean something to do with the install part that was fixed. Thanks Jim for the info.
-
Thank you very much for clearing that out for me. Somehow I was under the wrong impression. You can clean-up my posts if you like.
-
The pfSense 2.4.4-p2 has been on my dashboard for some days then now it's disappeared:
2.4.4-RELEASE-p1 (arm)
built on Thu Nov 29 14:06:34 EST 2018
FreeBSD 11.2-RELEASE-p4The system is on the latest version.
Version information updated at Tue Jan 22 15:03:08 CET 2019Why?
-
Could be all kinds of reasons.. If they would of pulled p2 then there would of been announcement.
I am currently having some issues getting to pfsense.org download sites.. So maybe network problem somewhere, or server issue. example https://snapshots.pfsense.org/ I currently having a problem accessing.
Well now I can get there - so maybe on my end, or maybe they cleared it up...
-
For all of you who missed the intel: They had a maintenance window at the NY datacenter from 2am to 5am this morning, so firmware/OS and package updates on that mirror were unavailable. Somehow they weren't available at all - I don't know why the other mirrors didn't kick in - but 99% sure that was the reason your dashboard wouldn't show the new version as the
pkg updatewasn't working at that time. @Summer try to re-check now, it should light ab right away. :) -
This thread is outdated and not for reporting problems. Start new threads for issues.
Locking.
