Multiple OpenVPN mapped to different WiFi SSID (Unifi)
-
@johnpoz Hhhhee I like how you think. I'm also trying to to make it rationale and use as less as possible wired and simplify topology .
I'm now setting up now Open VPN. Vlan already created and mapped to my LAN NIC igb1 . Let'see. .
-
Ok got the tunnel up . Cyberghost VPN is pain to setup and no really docs about it.
VLAN created, dhcp , subnet and range added to this VLAN , VLAN tagged in Unifi . NAT rule created to allow from this VLAN to WAN
No IP offered on this new VLAN . Maybe because I have created on Unifi a rule that block LAN traffic (Internet only like a guest) . I will further troubleshoot . Also becasue when this tunnel is up , normal LAN has no internet.
I only have a question about the GW to be assigned to this VLAN. In Pfsense I got this option uncheked. Not sure if in this case should be checked .
Use non-local GW: This will allow use of a gateway outside of this interface's subnet. This is usually indicative of a configuration error, but is required for some scenarios. -
When creating new "lan" side networks there would be no gateway assigned.. You just give the interface an IP.. say 192.168.2.1/24 if your lan is 192.168.1 for example.
You can route your different networks or even just specific devices out a vpn connection via policy routing - ie select the vpn as gateway in your firewall rule.
You almost never want to pull routes from some vpn service - they like you send everything through them... Which normally you would want to policy route.
-
That's a bit nasty on Unifi side . Each time they upgrade the controller , they remove features . Such as VLAN only network, now is mandatory an Unifi switch .
As result the DHCP on the new Pfsense VLAN can't hand over an IP to the new SSID , therefore I got a bogus IP assigned by Unifi .
Will still try to find solutions , otherwise I will use an old DDWRT AP to test -
What? Dude I run unifi AP I have vlans tagged and untagged... Not sure what your talking about? I am running 5.11.26 on controller and 4.0.43 firmware...
What would unifi be handing out IPs for??
You set your vlan ID as tagged on our switch connected to the AP... Set your SSID with vlan ID to match and there you go.
-
@johnpoz do you have AP only ? in my case yes .
I have created a new SSID , tagged on the Pfsense VLAN .
Now if I want to create in Unifi a new network (VLAN only), different from LAN , require an Unifi switch .
On the Pfsense VLAN, the firewall rule is pretty straight forward
-
dude you do not need to do that... You only need to do that if you have a switch..
Let me log in and will post screenshot.
You set the vlan ID on your wifi network
That network tab on the controller has nothing to do with it.
-
@johnpoz I guess I got your point. And indeed this is how I have configured it that struggles to work . I'm running a Docker version of the controller (does not really matter, is bridged to LAN)
-
If your client is not getting an IP from that vlan ID... Then you have a problem on your switch, or your vlan setup on pfsense or your not running dhcp...
All there is to do is set the vlan ID on your wireless network, and tag that to the AP..
-
@johnpoz There is no switch in between . Unifi AP straight forward in Pfsense LAN igb1 . DHCP server is running on that VLAN
-
So how exactly are you provisioning the AP? Its IP is also on vlan 49?
The AP talks to the controller normally via untagged... Where is your controller if you have the AP directly connected to your pfsense?
-
@johnpoz nope. AP is on the default LAN /24 . Works fine in that LAN.
-
And where is your controller? If you have the AP directly connected to your lan interface on pfsense? With no switch?
Draw up how you have everything connected...
-
@johnpoz Controller is running on Docker on a bridged LAN . Same main LAN subnet 192.168.1.0/24 . Just on it's own port 8443.
WAIT : I just remeber that I got a Tomato as bridge in between . Let me create a VLAN 49 there on the br0
-
Try a packet capture on VLAN49.
-
Well yeah is that bridge you setup going to pass the tags? Or anything... How do you have this all connected... Why would you be bridging on your tomato box?? And does it even support vlan tags... Dude get a SWITCH!!!
How do you have a "lab" and not have a switch that does vlan tags?
-
@johnpoz I got a switch . I have to connect it . Mostly is all virtual but I will get this switch up and test again .
-
This is pretty simple/basic stuff here... You tag the vlan, that is what is on the wifi ssid with that tag.. Been using these AP since 2014 ;) I just had to look that up for another thread... Got an old square uap-ac back then.. tagging ssid worked the same as it does now..
If its not working your loosing your tag somewhere, didn't set it up, etc. etc.
-
@johnpoz Indeed . upgrading this netgear firmware(with PoE) and I will put it in the game .
Forgot I had this tomato device in bridge plugged somewhere . Sorry about. -
@johnpoz all is working as intended. Again thanks for the help .
Last thing to solve is within the OpenVPN connection , is how to use my Pfsense / Pfblocker as DNS in the tunnel . Not sure where to look in this regard .
After that , I can export this config and us it in private LAN .Thanks again
