Very Confusing is OpenVPN Setup

rwhitney

@viragomann again my apologies - my local LAN is 192.168.1.1/24; the LAN I am trying to remote into is 192.168.0.1/24

rwhitney

I am attaching a screenshot:

this is the default gateway and the Static Routes table is again blank

viragomann

The routing table is the key here, but that one of the client!

rwhitney

@viragomann How do I display the client routing table or which one do you need to see?

rwhitney

@viragomann does this help?

Derelict

The first step to configuring a VPN is understanding what it is you are actually doing.

On the client, connect the VPN. Then print the routing table.

Some common command lines:

Windows: route print
Mac: netstat -rnfinet
Linux: netstat -rn4

You can use Diagnostics > Routes in the pfSense software.

stephenw10

@rwhitney said in Very Confusing is OpenVPN Setup:

I have set the route LAN network to 192.168.0.1/24

That should be 192.168.0.0/24 in the local subnets field. Unless you have set Redirect IPv4 Gateway in which case that should be not set anywhere as everything is routed.

Steve

rwhitney

@Derelict please pardon my dust as I AM learning!

===========================================================================
Interface List
  4...d0 17 c2 02 fb 3e ......Realtek PCIe GBE Family Controller
 18...16 c6 3b 02 82 0f ......Microsoft Wi-Fi Direct Virtual Adapter
 13...26 c6 3b 02 82 0f ......Microsoft Wi-Fi Direct Virtual Adapter #2
 19...00 ff f9 1a 4d b8 ......TAP Adapter OAS NDIS 6.0
 16...00 ff e2 a9 d8 ab ......TAP-Windows Adapter V9
 10...74 c6 3b 02 82 0f ......Qualcomm Atheros AR9485 Wireless Network Adapter
  1...........................Software Loopback Interface 1
===========================================================================

IPv4 Route Table
===========================================================================
Active Routes:
Network Destination        Netmask          Gateway       Interface  Metric
          0.0.0.0          0.0.0.0      192.168.1.1     192.168.1.12     55
          0.0.0.0        128.0.0.0         10.0.8.1         10.0.8.3    291
         10.0.8.0    255.255.255.0         On-link          10.0.8.3    291
         10.0.8.3  255.255.255.255         On-link          10.0.8.3    291
       10.0.8.255  255.255.255.255         On-link          10.0.8.3    291
     98.174.x.x  255.255.255.255      192.168.1.1     192.168.1.12    311
        127.0.0.0        255.0.0.0         On-link         127.0.0.1    331
        127.0.0.1  255.255.255.255         On-link         127.0.0.1    331
  127.255.255.255  255.255.255.255         On-link         127.0.0.1    331
        128.0.0.0        128.0.0.0         10.0.8.1         10.0.8.3    291
      192.168.1.0    255.255.255.0         On-link      192.168.1.12    311
     192.168.1.12  255.255.255.255         On-link      192.168.1.12    311
    192.168.1.255  255.255.255.255         On-link      192.168.1.12    311
        224.0.0.0        240.0.0.0         On-link         127.0.0.1    331
        224.0.0.0        240.0.0.0         On-link          10.0.8.3    291
        224.0.0.0        240.0.0.0         On-link      192.168.1.12    311
  255.255.255.255  255.255.255.255         On-link         127.0.0.1    331
  255.255.255.255  255.255.255.255         On-link          10.0.8.3    291
  255.255.255.255  255.255.255.255         On-link      192.168.1.12    311
===========================================================================
Persistent Routes:
  None

rwhitney

@stephenw10 setting it to 192.168.0.0/24 does not seem to make a difference - I did have it set to Redirect IPv4 Gateway, but have removed that

rwhitney

Just to indicate my gratitude to everyone who has offered advice in this thread - thank you! (I am not yet connected to internal LAN however)

stephenw10

It's still sending route all and not just 192.168.0.0/24.

Try restarting the server end to be sure that new setting in place and then check the Windows client routing table.

Steve

rwhitney

@stephenw10 so reboot the netgate server? I will have to wait a couple of hours first

Derelict

No. Restart the OpenVPN process. (Status > Services, stop it and start it. This is restarted when you make a change like disabling the redirect gateway push but Steve is just being thorough.)

rwhitney

@Derelict I just restarted the running process for openvpn. I did just notice that I am getting a connection error: key registration failed to occur within 60 seconds... I am trying this from a Windows laptop at work through an external wirelass network. I don't have this connectivity problem from home on my linux box - just from there I still cannot see the local LAN here at work. All I can see is the firewall

rwhitney

@viragomann Here is my server setting for Tunnel:

I do not see a setting for Remote Network in OpenVPN > Server

viragomann

@rwhitney
That was wrong. It should be "Local Networks".
I'll correct it above.

rwhitney

@viragomann Oh, so I do have something correct?!!

viragomann

@rwhitney
Yeah!

rwhitney

@viragomann
If I were to start from scratch, what would be the first thing to do? (setup the Cert?)
second: setup an openvpn server: (I think I have this set).
Third: setup a user?
Fourth: setup a user cert?
Fifth: download config from Client Export
What am I missing?

viragomann

Your setup looks well, however starting from scratch with the OpenVPN part may help making it work.

The cert should not be wrong as long as you've generated the correct type (CA, server, client).

Apart from this, I start with the certs:
CA
server
client(s)

Then I set up the server and at last I export the config and install it on the client computer.