add new Congestion-Control Algorithms
-
It appears that most errors are being logged on your LAGG port. I am going to assume that the same errors are not showing on the stats for the LAGG members ? If that is the case, only time I've seen this behavior is when you have ports LAGGed but not all of them have actual active links, so say, you have igb0 thru igb3 in a LAGG conf, but igb1 is actually disconnected (Physically). Other than that, I am unsure what the issue might be. Sorry.
-
@mrancier said in add new Congestion-Control Algorithms:
It appears that most errors are being logged on your LAGG port. I am going to assume that the same errors are not showing on the stats for the LAGG members ? If that is the case, only time I've seen this behavior is when you have ports LAGGed but not all of them have actual active links, so say, you have igb0 thru igb3 in a LAGG conf, but igb1 is actually disconnected (Physically). Other than that, I am unsure what the issue might be. Sorry.
thanks, What should I check or how to determine the problem? i am using two intel I350-T2 NIC. one nic two interface for pppoe wan, and one for lagged to LAN switch.
igb0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> metric 0 mtu 1500
options=e500bb<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,JUMBO_MTU,VLAN_HWCSUM,VLAN_HWFILTER,VLAN_HWTSO,RXCSUM_IPV6,TXCSUM_IPV6>
ether a0:36:9f:83:90:40
media: Ethernet autoselect (1000baseT <full-duplex>)
status: active
nd6 options=21<PERFORMNUD,AUTO_LINKLOCAL>
igb1: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> metric 0 mtu 1500
options=e500bb<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,JUMBO_MTU,VLAN_HWCSUM,VLAN_HWFILTER,VLAN_HWTSO,RXCSUM_IPV6,TXCSUM_IPV6>
ether a0:36:9f:83:90:40
hwaddr a0:36:9f:83:90:41
media: Ethernet autoselect (1000baseT <full-duplex>)
status: active
nd6 options=21<PERFORMNUD,AUTO_LINKLOCAL>
igb2: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> metric 0 mtu 1508
options=e520bb<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,JUMBO_MTU,VLAN_HWCSUM,WOL_MAGIC,VLAN_HWFILTER,VLAN_HWTSO,RXCSUM_IPV6,TXCSUM_IPV6>
ether 24:fd:52:3f:40:56
hwaddr a0:36:9f:83:8b:5c
inet6 fe80::26fd:52ff:fe3f:4656%igb2 prefixlen 64 scopeid 0x3
media: Ethernet autoselect (1000baseT <full-duplex>)
status: active
nd6 options=21<PERFORMNUD,AUTO_LINKLOCAL>
igb3: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> metric 0 mtu 1508
options=e500bb<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,JUMBO_MTU,VLAN_HWCSUM,VLAN_HWFILTER,VLAN_HWTSO,RXCSUM_IPV6,TXCSUM_IPV6>
ether 44:6e:e5:1d:b0:a7
hwaddr a0:36:9f:83:8b:5d
inet6 fe80::466e:e5ff:fe1d:b4a7%igb3 prefixlen 64 scopeid 0x4
media: Ethernet autoselect (1000baseT <full-duplex>)
status: active
nd6 options=21<PERFORMNUD,AUTO_LINKLOCAL>
re0: flags=8802<BROADCAST,SIMPLEX,MULTICAST> metric 0 mtu 1500
options=8209b<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,VLAN_HWCSUM,WOL_MAGIC,LINKSTATE>
ether bc:5f:f4:7b:29:6d
media: Ethernet autoselect (none)
status: no carrier
nd6 options=21<PERFORMNUD,AUTO_LINKLOCAL>
enc0: flags=0<> metric 0 mtu 1536
groups: enc
nd6 options=21<PERFORMNUD,AUTO_LINKLOCAL>
lo0: flags=8049<UP,LOOPBACK,RUNNING,MULTICAST> metric 0 mtu 16384
options=680003<RXCSUM,TXCSUM,LINKSTATE,RXCSUM_IPV6,TXCSUM_IPV6>
inet6 ::1 prefixlen 128
inet6 fe80::1%lo0 prefixlen 64 scopeid 0x7
inet 127.0.0.1 netmask 0xff000000
groups: lo
nd6 options=21<PERFORMNUD,AUTO_LINKLOCAL>
pfsync0: flags=0<> metric 0 mtu 1500
syncpeer: 224.0.0.240 maxupd: 128 defer: on
syncok: 1
groups: pfsync
pflog0: flags=100<PROMISC> metric 0 mtu 33160
groups: pflog
lagg0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> metric 0 mtu 1500
options=e500bb<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,JUMBO_MTU,VLAN_HWCSUM,VLAN_HWFILTER,VLAN_HWTSO,RXCSUM_IPV6,TXCSUM_IPV6>
ether a0:36:9f:83:90:40
inet6 fe80::a236:9fff:fe83:9940%lagg0 prefixlen 64 scopeid 0xa
inet6 2602:fed5:7021::face prefixlen 48
inet 185.230.191.1 netmask 0xffffffe0 broadcast 185.230.191.31
inet 185.230.191.2 netmask 0xffffff00 broadcast 185.230.191.255
laggproto lacp lagghash l2,l3,l4
laggport: igb0 flags=1c<ACTIVE,COLLECTING,DISTRIBUTING>
laggport: igb1 flags=1c<ACTIVE,COLLECTING,DISTRIBUTING>
groups: lagg
media: Ethernet autoselect
status: active
nd6 options=21<PERFORMNUD,AUTO_LINKLOCAL>LADVD Devices
Capability Codes:
r - Repeater, B - Bridge, H - Host, R - Router, S - Switch,
W - WLAN Access Point, C - DOCSIS Device, T - Telephone, O - OtherDevice ID Local Intf Proto Hold-time Capability Port ID
H3C igb1 LLDP 119 BR Gi1/0/5 In
H3C igb0 LLDP 119 BR Gi1/0/7 In
LADVD Detailed decode
Chassis id: 04:d7:a5:db:db:16
Port id: 04:d7:a5:db:db:1c
Time remaining: 119 seconds
Port Description: GigabitEthernet1/0/5 Interface
System Name: H3C
System Description:
H3C Switch S1850-10P Software Version 5.20.99, Release 1102
Copyright(c)2004-2017 New H3C Technologies Co., Ltd. All rights reserved.
System Capabilities: BR
Enabled Capabilities: BR
Management Address IPv4: 192.168.0.233
Port VLAN ID: 1Chassis id: 04:d7:a5:db:db:16
Port id: 04:d7:a5:db:db:1e
Time remaining: 119 seconds
Port Description: GigabitEthernet1/0/7 Interface
System Name: H3C
System Description:
H3C Switch S1850-10P Software Version 5.20.99, Release 1102
Copyright(c)2004-2017 New H3C Technologies Co., Ltd. All rights reserved.
System Capabilities: BR
Enabled Capabilities: BR
Management Address IPv4: 192.168.0.233
Port VLAN ID: 1 -
i try deleted lagg, change to normal lan interface.
use netstat -in show all normal.
but netstat -s still show 2929 packets not forwardable. so the route in still show packet loss.
ip:
110688 total packets received
0 bad header checksums
0 with size smaller than minimum
0 with data size < data length
0 with ip length > max ip packet size
0 with header length < data size
0 with data length < header length
0 with bad options
0 with incorrect version number
0 fragments received
0 fragments dropped (dup or out of space)
0 fragments dropped after timeout
0 packets reassembled ok
62783 packets for this host
0 packets for unknown/unsupported protocol
35269 packets forwarded (0 packets fast forwarded)
2929 packets not forwardable
0 packets received for unknown multicast group
0 redirects sent
67139 packets sent from this host
0 packets sent with fabricated ip header
0 output packets dropped due to no bufs, etc.
2742 output packets discarded due to no route
0 output datagrams fragmented
0 fragments created
0 datagrams that can't be fragmented
0 tunneling packets that can't find gif
0 datagrams with bad address in headertcp:
29618 packets sent
1843 data packets (2075087 bytes)
1 data packet (126 bytes) retransmitted
2 data packets unnecessarily retransmitted
0 resends initiated by MTU discovery
27749 ack-only packets (0 delayed)
0 URG only packets
0 window probe packets
10 window update packets
16 control packets
28200 packets received
433 acks (for 2074414 bytes)
49 duplicate acks
0 acks for unsent data
22516 packets (27777099 bytes) received in-sequence
11 completely duplicate packets (8678 bytes)
0 old duplicate packets
0 packets with some dup. data (0 bytes duped)
5214 out-of-order packets (6964840 bytes)
0 packets (0 bytes) of data after window
0 window probes
8 window update packets
2 packets received after close
0 discarded for bad checksums
0 discarded for bad header offset fields
0 discarded because packet too short
0 discarded due to memory problems
10 connection requests
3 connection accepts
1 bad connection attempt
0 listen queue overflows
0 ignored RSTs in the windows
12 connections established (including accepts)
0 times used RTT from hostcache
0 times used RTT variance from hostcache
0 times used slow-start threshold from hostcache
46 connections closed (including 3 drops)
0 connections updated cached RTT on close
0 connections updated cached RTT variance on close
0 connections updated cached ssthresh on close
0 embryonic connections dropped
372 segments updated rtt (of 379 attempts)
4 retransmit timeouts
0 connections dropped by rexmit timeout
0 persist timeouts
0 connections dropped by persist timeout
0 Connections (fin_wait_2) dropped because of timeout
29 keepalive timeouts
29 keepalive probes sent
0 connections dropped by keepalive
350 correct ACK header predictions
22475 correct data packet header predictions
3 syncache entries added
0 retransmitted
0 dupsyn
0 dropped
3 completed
0 bucket overflow
0 cache overflow
0 reset
0 stale
0 aborted
0 badack
0 unreach
0 zone failures
1 cookie sent
0 cookies received
0 hostcache entries added
0 bucket overflow
0 SACK recovery episodes
0 segment rexmits in SACK recovery episodes
0 byte rexmits in SACK recovery episodes
0 SACK options (SACK blocks) received
4748 SACK options (SACK blocks) sent
0 SACK scoreboard overflow
0 packets with ECN CE bit set
26630 packets with ECN ECT(0) bit set
0 packets with ECN ECT(1) bit set
9 successful ECN handshakes
1 time ECN reduced the congestion window
0 packets with matching signature received
0 packets with bad signature received
0 times failed to make signature due to no SA
0 times unexpected signature received
0 times no signature provided by segment
0 Path MTU discovery black hole detection activations
0 Path MTU discovery black hole detection min MSS activations
0 Path MTU discovery black hole detection failures
TCP connection count by state:
0 connections in CLOSED state
15 connections in LISTEN state
0 connections in SYN_SENT state
0 connections in SYN_RCVD state
6 connections in ESTABLISHED state
0 connections in CLOSE_WAIT state
0 connections in FIN_WAIT_1 state
0 connections in CLOSING state
0 connections in LAST_ACK state
0 connections in FIN_WAIT_2 state
0 connections in TIME_WAIT state
udp:
38109 datagrams received
0 with incomplete header
0 with bad data length field
0 with bad checksum
0 with no checksum
26 dropped due to no socket
458 broadcast/multicast datagrams undelivered
0 dropped due to full socket buffers
0 not for hashed pcb
37625 delivered
37845 datagrams output
0 times multicast source filter matched -
Typically when you see counters for packets not forwardable in netstat, it is because you are missing a route to localhost.
For reference :
https://docs.oracle.com/cd/E19253-01/816-4555/ppp.trouble-108/index.html
-
@mrancier said in add new Congestion-Control Algorithms:
Typically when you see counters for packets not forwardable in netstat, it is because you are missing a route to localhost
What rules or routes do I need to add?
-
@yon-0 Hard to say without a visual, but I will ask this : If the issue does happen on 2.4.4p3, there is a possibility, albeit small, that there may be a bug in the PPPoE client.
-
@mrancier i am using pf2.5 newest version
-
ip6:
1301746 total packets received
0 with size smaller than minimum
0 with data size < data length
0 with bad options
18 with incorrect version number
0 fragments received
0 fragments dropped (dup or out of space)
0 fragments dropped after timeout
0 fragments that exceeded limit
0 packets reassembled ok
416553 packets for this host
855286 packets forwarded
2615 packets not forwardable
0 redirects sent
500503 packets sent from this host
0 packets sent with fabricated ip header
0 output packets dropped due to no bufs, etc.
1225 output packets discarded due to no route
0 output datagrams fragmented
0 fragments created
0 datagrams that can't be fragmented
0 packets that violated scope rules
325 multicast packets which we don't join
Input histogram:
hop by hop: 235
TCP: 568585
UDP: 597299
ICMP6: 135609
Mbuf statistics:
557747 one mbuf
two or more mbuf:
lo0= 2398
741601 one ext mbuf
0 two or more ext mbuf
0 packets whose headers are not contiguous
0 tunneling packets that can't find gif
0 packets discarded because of too many headers
450 failures of source address selection
source addresses on an outgoing I/F
8986 link-locals
11506 globals
source addresses on a non-outgoing I/F
2 globals
450 addresses scope=0xf
source addresses of same scope
8984 link-locals
11508 globals
source addresses of a different scope
2 link-locals
Source addresses selection rule applied:
20494 first candidate
450 same address
8290 appropriate scope
3216 outgoing interface
885 longest match -
@yon-0 said in add new Congestion-Control Algorithms:
packets not forwardable
netstat -m
40123/4667/44790 mbufs in use (current/cache/total)
11125/2311/13436/1000000 mbuf clusters in use (current/cache/total/max)
102/2175 mbuf+clusters out of packet secondary zone in use (current/cache)
2/206/208/524288 4k (page size) jumbo clusters in use (current/cache/total/max)
0/0/0/524288 9k jumbo clusters in use (current/cache/total/max)
0/0/0/124480 16k jumbo clusters in use (current/cache/total/max)
32295K/6612K/38908K bytes allocated to network (current/cache/total)
0/0/0 requests for mbufs denied (mbufs/clusters/mbuf+clusters)
0/0/0 requests for mbufs delayed (mbufs/clusters/mbuf+clusters)
0/0/0 requests for jumbo clusters delayed (4k/9k/16k)
0/0/0 requests for jumbo clusters denied (4k/9k/16k)
0 sendfile syscalls
0 sendfile syscalls completed without I/O request
0 requests for I/O initiated by sendfile
0 pages read by sendfile as part of a request
0 pages were valid at time of a sendfile request
0 pages were valid and substituted to bogus page
0 pages were requested for read ahead by applications
0 pages were read ahead by sendfile
0 times sendfile encountered an already busy page
0 requests for sfbufs denied
0 requests for sfbufs delayed -
@mrancier said in add new Congestion-Control Algorithms:
Cc_cdg.ko depends on h_ertt, so both modules need to be there, otherwise cdg will fail kload.
what's CUBIC need load modules?
-
cc_cubic.ko is the name.
-
cubic and cdg still unable to solve the problem of no speed caused by carrier network packet loss. There is a need to increase competitiveness and prevent the impact of ISP QOS on us.
-
now the pf 2.5 version not work for this .
-
why pfsense v2.5 cant load the freebsd v12.1 cc_htcp so on?
kldload h_ertt kldload: an error occurred while loading module h_ertt. Please check dmesg(8) for more details. [2.5.0-DEVELOPMENT][admin@]/root: kldload cc_htcp kldload: an error occurred while loading module cc_htcp. Please check dmesg(8) for more details -
pf 2.4.5 -p1 still work, pf2.5 not work, added cdg
kldstat Id Refs Address Size Name 1 18 0xffffffff80200000 37191d8 kernel 2 1 0xffffffff83a21000 10c0 cpuctl.ko 3 1 0xffffffff83a23000 7028 aesni.ko 4 1 0xffffffff83a2b000 32d8 cryptodev.ko 5 1 0xffffffff83a2f000 1580 amdtemp.ko 6 1 0xffffffff83a31000 848 amdsmn.ko 7 2 0xffffffff83a32000 850 h_ertt.ko 8 1 0xffffffff83a33000 1dc4 cc_cdg.ko -
@yon-0 Liked your consistent testing ... good job!
-
@yon-0 Sorry about the lack of response. I was unaware you'd replied. Unfortunately, I've moved on to a competing product which is already on the freebsd 12.1 release in production and has ZERO issues with any and all mods to the underlying OS.
-
@mrancier said in add new Congestion-Control Algorithms:
@yon-0 Sorry about the lack of response. I was unaware you'd replied. Unfortunately, I've moved on to a competing product which is already on the freebsd 12.1 release in production and has ZERO issues with any and all mods to the underlying OS.
what is your using system now? i have try opnsense, But I am not very familiar with it, and there are some usage problems.
Yes, there are a lot of system problems here. Many of them are too late to report, and there are still many problems that have not been reported. It's just that I have been using it and the operation is more familiar.
-
@yon-0 Opnsense 20.7.1. Modules are readily available in the OS and load without issue. I have used htcp, cdg and cubic. Currently on Cubic and works quite well. Also, seems to be better at respecting loader.conf and loader.conf.local mods. No hardcoded kernel patches that I am aware of anyway.
-
@mrancier said in add new Congestion-Control Algorithms:
@yon-0 Opnsense 20.7.1. Modules are readily available in the OS and load without issue. I have used htcp, cdg and cubic. Currently on Cubic and works quite well. Also, seems to be better at respecting loader.conf and loader.conf.local mods. No hardcoded kernel patches that I am aware of anyway.
Have a chance to learn from you.
