ATT Uverse RG Bypass (0.2 BTC)
-
@Selcouth You should be able to confirm a working config by connecting the ONT to pfsense by way of a dumb switch (t o filter out the vlan 0 tags). ONT goes to one port, pfsense's wan goes to another.
-
@Selcouth I'm running supplicant mode on an SG-5100 on 2.4.5-RELEASE-p1 (amd64). I purchased the certificates from maczrcool on eBay and followed the guide in the README in the supplicant branch of MonkWho's pfatt fork: https://github.com/MonkWho/pfatt/tree/supplicant
-
@bk150 It looks like that method is funneling all wan traffic through ngeth0 for the vlan0 tagging. First off are you able to attain full line speed (during speed tests)? Is the pfsense cpu usage very high during this event?
-
@GPz1100 Here is a result from just a few moments ago:
Here's a screenshot of CPU usage and load average on the system during the test:
-
I wonder if the usage would be that high if a dumb switch was placed inline in between ont and pfsense wan?
-
@GPz1100 I'm not authenticating with a dumb switch in line either. I must have some other problem. Maybe I'll start fresh to double check everything.
-
@GPz1100 I'll find a day/evening when my girlfriend doesn't need internet and try the dumbswitch method. I can post my results back here
-
Hello All.
I am able to get this script working via bridge mode, but having issues getting it to work via supplicant mode. It is running on bare metal.The script seems to hang at "Waiting EAP for authorization"
I have root and wheel group full permission to the 3 certs. I got them from ebay and converted them into the correct format using some tools suggested online. Is there anything easy I could be missing? Been through the guide multiple times but cannot seem to figure it out thus far.
I have checked the configuration inside pfatt.sh multiple times and appears to be correct.
-
i following this thread with lot of interest
-
I had the same issue as above with the 'no such file or directory' errors and resolved it by adding the following lines in the pfatt.sh script around line 144:
/usr/bin/logger -st "pfatt" "attaching interfaces to ng_ether..."
/usr/local/bin/php -r "pfSense_ngctl_attach('.', '$ONT_IF');"The lines were added right after:
/usr/bin/logger -st "pfatt" " ONT---[] [$ONT_IF]$HOST"I had to set the WAN interface back to ngeth0, but after a reboot, I was getting an IP address and was able to browse the net. Hope this helps.
-
@Dade I realize you posted this a long time ago, so sorry for bringing this up again. I also have ATT with 5 extra static IPs (/29). I made another lan interface and assigned the "Gateway IP" from ATT to this interface. I don't have any problem using 1:1 NAT to assign public IPs to specific devices on my LAN.
I am also using the static "Gateway IP" from ATT as the IP address for a VPN server--which works except for one thing. My ATT static Gateway IP is 75.xxx.xxx.78. My dynamic ATT IP is 68.xxx.xxx.29. I can connect to the VPN using the address 75.xxx.xxx.78, but while connected to this VPN, if I google "what is my IP address" the response is 68.xxx.xxx.29, when it should be 75.xxx.xxx.78.
Using your method, were you able to resolve this? Either way, could you describe the firewall/NAT rules that you used?
Thanks!
-
@Ican-treadorwrite The IP you're going to see on a "what's my IP" query is going to be the NAT IP that applies to that traffic. You'll have to create a new NAT rule ONLY for the internal IP addresses of your VPN clients specifying that that specific IP (your static IP) is the "NAT address" for that traffic.
-
@bkatt said in ATT Uverse RG Bypass (0.2 BTC):
Hello All.
I am able to get this script working via bridge mode, but having issues getting it to work via supplicant mode. It is running on bare metal.The script seems to hang at "Waiting EAP for authorization"
I have root and wheel group full permission to the 3 certs. I got them from ebay and converted them into the correct format using some tools suggested online. Is there anything easy I could be missing? Been through the guide multiple times but cannot seem to figure it out thus far.
I have checked the configuration inside pfatt.sh multiple times and appears to be correct.
I am having this exact same situation. Permissions, names, etc all look fine - it just hangs at 'waiting EAP for authorisation'....
-
@shad0wca7
What are your file names and file type?
I have my permissions set to 755 -
I really hope the underlying issue people are having isn't related to this: https://www.dslreports.com/forum/r32839785-AT-T-Fiber-Gateway-bypass-with-WPA-supplicant-stopped-working-2-days-ago
-
@bk150
I'm running 2.4.5 and rebooted just the other day with no problems. -
-rw------- 1 root wheel 6431 Aug 22 16:46 ca.pem -rw------- 1 root wheel 1131 Aug 22 16:46 client.pem -rw------- 1 root wheel 887 Aug 22 16:46 private.pem -
@AiC0315 I set my permissions to 775 and tested. It was previously set to 774. Unfortunately same message, "Waiting EAP for Autorization". Three files, ca.pem, client.pem, and private.pem. running 2.4.5 r1 also.
-
-
I recently set up new service with AT&T and was not able to get wpa_supplicant/dhcp working without making a few tweaks to the
pfatt.shscript:wpa_supplicanthad to run on the bare port, notngeth0-WPA_DAEMON_CMD="/usr/sbin/wpa_supplicant -Dwired -ingeth0 -B -C /var/run/wpa_supplicant" +WPA_DAEMON_CMD="/usr/sbin/wpa_supplicant -Dwired -i$ONT_IF -B -C /var/run/wpa_supplicant"- Both the bare port and
ngeth0had to have a MAC that matched the certificates I was using (not my assigned router gateway, as I had purchased certificates online instead of messing with the firmware of my assigned gateway):-/usr/sbin/ngctl msg ngeth0: set $RG_ETHER_ADDR +/usr/sbin/ngctl msg ngeth0: set $EAP_SUPPLICANT_IDENTITY /usr/bin/logger -st "pfatt" "enabling promisc for $ONT_IF..." +/sbin/ifconfig $ONT_IF ether $EAP_SUPPLICANT_IDENTITY /sbin/ifconfig $ONT_IF up /sbin/ifconfig $ONT_IF promisc
This got me line speeds with minimal CPU usage on a bare metal installation of pfsense (CPU is a Xeon D-1518 @ 2.2Ghz, for reference, which is overkill for this but not the 10Gbps ports)
That said, I still do not have IPV6 working fully, and am at a loss there-- I can get a WAN IP via DHCPv6, and I can get prefix delegations for all of my LANs, but IPv6 packets just get dropped several hops outside of my network without the slightest hint as to why.
