Routing doesn't work with OpenVPN peer to peer.

JeGr

@dimskraft Normally from top to bottom.

Check firewall rules if both sides allow traffic incoming on OVPN interface
Check routes in Diagnostics if established VPN shows the correct routes for the remote network and vice versa
Check if pfsense box A can ping box B (tunnel IPs only, to check raw connectivity of gateways)
Check from a box inside LAN A if it can reach VPN Gateway on B side and vice versa
Chcek if a box on A can ping a box on B

for the last three steps if answer is "no", check with firewall rules, logs and packet capture if packets take the right way and are allowed on both sides.

Cheers

dimskraft

@jegr I didn't create ovpn interfaces, I have specified rules on OpenVPN tab as described here https://docs.netgate.com/pfsense/en/latest/recipes/openvpn-s2s-tls.html

JeGr

@dimskraft So you answered to one question and ignored all others? ;)

marvosa

@dimskraft
Lots of different variables to look at... do the routes exists, are the firewalls allowing the traffic, are the clients using PFsense as the default gateway, etc.

Post the server1.conf and client1.conf.

chpalmer

Anything outside of the subnet of your Windows machines on each end will be treated as a public connection and firewalled off by your local machines.

Make sure those machines have firewall rules allowing the connection from something outside of their own subnet.

I have 12 OpenVPN tunnels going from here to remote sites and they all work flawlessly.

dimskraft

@jegr was just not ready yet...

firewall rules look ok according to manual (allowing all incoming from vpn on vpn tab)
routes look correct as far as I can judge

Machine 1:

Machine 2:

can't ping in both directions

On machine 1 I can ping 192.168.27.1 (itself) but can't ping 192.168.27.2 while on machine 2 I can ping 192.168.27.2 (itself), but can't ping 192.168.27.1

4,5) can't

Packet capture see nothing

For example if I do

tcpdump -i ovpns4 icmp

on machine 1, and do any ping of 192.168.27.1, including successfull pings on LAN 1 side, it shows nothing

viragomann

@dimskraft said in Routing doesn't work with OpenVPN peer to peer.:

firewall rules look ok according to manual (allowing all incoming from vpn on vpn tab)

Would be better to post a screenshot here, so that others can get a view on it.

Did you set also the protocol to any in the rule?

dimskraft

@viragomann apparently yes

on machine 1

on machine 2

dimskraft

@chpalmer I know about this thing but I am not using Windows machines yet, I am trying to ping between pfsenses or between Linux machines in connected LANs.

Do they have the same option?

May be I should use the same subnet in both connected LANs?

dimskraft

Apparently routes are computing correctly

On machine 1 to machine 2:

: route get 192.168.33.246
   route to: 192.168.33.246
destination: 192.168.33.0
       mask: 255.255.255.0
    gateway: 192.168.27.2
        fib: 0
  interface: ovpns4
      flags: <UP,GATEWAY,DONE,STATIC>
 recvpipe  sendpipe  ssthresh  rtt,msec    mtu        weight    expire
       0         0         0         0      1500         1         0

On machine 2

: route get 192.168.10.25
   route to: 192.168.10.25
destination: 192.168.10.0
       mask: 255.255.255.0
    gateway: 192.168.27.1
        fib: 0
  interface: ovpnc1
      flags: <UP,GATEWAY,DONE,STATIC>
 recvpipe  sendpipe  ssthresh  rtt,msec    mtu        weight    expire
       0         0         0         0      1500         1         0

dimskraft

My machine 1 is multi WAN and it has firewall rule for LAN assigned to gateway group, not everything. May be this is affecting?

dimskraft

It was compression issue.

I understood it when looking at server OpenVPN logs and seeing error

IP packet with unknown IP version=15 seen

Some compression was turned ON on client side but any compression was disabled on server side. I was sure this misconfig would be detected automatically