pfsense VM gets stuck
-
@panicos deploy a new pfsense vm? and transfer config, see the outcome.
-
I'm not using esxi myself but I would check if you esxi version has known issues with stock FreeBSD 12.2. Look for guide line how to make FreeBSD 1..2 works with your VM.
Any suspect message on the console while booting ?
Like NIC's are found etc ? -
@mr-rosh you think that would solve it? I will wait and see if it jams again, then i will try your advice also.
-
@gertjan there is no suspect message on console while booting. Looking at a VMware Compatibility Guide, i see free bsd 12.2 is supported starting with esxi 6.7, while on my version the supported one is free bsd 11.x
I anyway, just have a dropdown to choose freebsd 32 or 64 bit (no version to choose from).
On the other hand, the former esxi 6.0 which i had been runing for 2 years, had no freebsd support (according to the ocmpatibility matrix vmware) and it was working flawlesy (the pfsense i mean). -
@mr-rosh it is not working. i tried. reinstalled from scratch the pfsense in a new VM. i get the same problem. When i push some traffic through it, it gets stuck , innacessible. Only rebooting the host helps.
I am geting panicked
-
@panicos whats the network adapter on esxi host?
-
@mr-rosh i have not physically opened the host to check it, but based on what i see in the cli , it is a Intel Gigabit ET Quad Port Server Adapter
[root@localhost:~] vmware -vl
VMware ESXi 6.5.0 build-17167537
VMware ESXi 6.5.0 Update 3
[root@localhost:~]
[root@localhost:~] esxcli network nic list | grep In
vmnic2 0000:03:00.0 igb Up Up 1000 Full 00:1b:21:9f:d0:08 1500 Intel Corporation 82576 Gigabit Network Connection
vmnic3 0000:03:00.1 igb Up Up 1000 Full 00:1b:21:9f:d0:09 1500 Intel Corporation 82576 Gigabit Network Connection
vmnic4 0000:04:00.0 igb Up Up 1000 Full 00:1b:21:9f:d0:0c 1500 Intel Corporation 82576 Gigabit Network Connection
vmnic5 0000:04:00.1 igb Up Up 1000 Full 00:1b:21:9f:d0:0d 1500 Intel Corporation 82576 Gigabit Network Connection
[root@localhost:~][root@localhost:~] esxcli network nic get -n vmnic2
Advertised Auto Negotiation: true
Advertised Link Modes: 10BaseT/Half, 10BaseT/Full, 100BaseT/Half, 100BaseT/Full, 1000BaseT/Full
Auto Negotiation: true
Cable Type: Twisted Pair
Current Message Level: 7
Driver Info:
Bus Info: 0000:03:00.0
Driver: igb
Firmware Version: 1.5, 0x00011d40
Version: 5.3.3
Link Detected: true
Link Status: Up
Name: vmnic2
PHYAddress: 1
Pause Autonegotiate: true
Pause RX: false
Pause TX: false
Supported Ports: TP
Supports Auto Negotiation: true
Supports Pause: true
Supports Wakeon: true
Transceiver: internal
Virtual Address: 00:50:56:57:1a:86
Wakeon: MagicPacket(tm)
[root@localhost:~][root@localhost:~] vmkchdev -l |grep vmnic[2-5]
0000:03:00.0 8086:10e8 8086:a02c vmkernel vmnic2
0000:03:00.1 8086:10e8 8086:a02c vmkernel vmnic3
0000:04:00.0 8086:10e8 8086:a02c vmkernel vmnic4
0000:04:00.1 8086:10e8 8086:a02c vmkernel vmnic5
[root@localhost:~] -
I have found the problem in the meantime: i have a nic teaming between esxi and the physical switch; although i have configured this following official guides, it appears the arp broadcast is not flowing through it and the vswitch becomes saturated, denying all the traffic. maybe i am hitting a but or something. I will carry on from here on the virtualization part.
Thanks everyone for the suggestions.
Ticket may be closed. -
@panicos When using multiple NICs, it is critical that the VMWare NIC Teaming be configured correctly to match the switch to which the ports are connected.
Based on personal experience, I find that Route based on the originating virtual port ID works ok if there are no LAGs created on the switch, but that if you are using a switch LAG, then route based on IP hash is needed. -
@awebster yes, you are right. i have an etherchannel on the switch and nic teaming with IP hash on the esx. the configuration is not a problem; i followed guides for it.
Problem might be with the network card's driver in esxi, which although it is supported, it might have some problems.