Pfsense on Hyper-v 2016 no system logs. (Resolved)



  • Just did a new install.  Logged into web interface and no logs showing up in web interface. 2.3.3-RELEASE

    See serial output below:

    syslogd: /var/log/routing.log: Operation not supported by device

    May  4 00:24:51  syslogd: /var/log/ntpd.log: Operation not supported by device

    May  4 00:24:51  syslogd: /var/log/ppp.log: Operation not supported by device

    May  4 00:24:51  syslogd: /var/log/poes.log: Operation not supported by device

    May  4 00:24:51  syslogd: /var/log/l2tps.log: Operation not supported by device

    done.
    May  4 00:24:51  syslogd: /var/log/ipsec.log: Operation not supported by device

    Setting up interfaces microcode…May  4 00:24:51  syslogd: /var/log/openvpn.log: Operation not supported by device

    done.
    May  4 00:24:51  syslogd: /var/log/gateways.log: Operation not supported by device

    May  4 00:24:51  syslogd: /var/log/resolver.log: Operation not supported by device

    May  4 00:24:51  syslogd: /var/log/dhcpd.log: Operation not supported by device

    May  4 00:24:51  syslogd: /var/log/relayd.log: Operation not supported by device

    May  4 00:24:51  syslogd: /var/log/wireless.log: Operation not supported by device

    =~=~=~=~=~=~=~=~=~=~=~= PuTTY log 2017.05.04 00:24:25 =~=~=~=~=~=~=~=~=~=~=~=
    \|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\                                                                                                           ______                       /      \                _____/    f   \              /     \        /             /   p   \______/  Sense       \       /      \               \_____/        \                    \        /                     \______/                                                                                                 |/-\          __ ____                            _ __  / _/ ___|  ___ _ __  ___  ___      | '_ \| |_\___ \ / _ \ '_ \/ __|/ _ \     | |_) |  _|___) |  __/ | | \__ \  __/     | .__/|_| |____/ \___|_| |_|___/\___|     |_|                                                                                ||||||||||||||||||||||||==================================================================================++++|/-\|/-\|/-\|/Welcome to pfSense1 .Boot Multi User [Enter]2 .Boot [S]ingle User3 .[Esc]ape to loader prompt4 .RebootOptions:5 .[K]ernel: kernel (1 of 2)6 .Configure Boot [O]ptions...Autoboot in 2 seconds. [Space] to pauseAutoboot in 1 seconds. [Space] to pause                                       -\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|//boot/kernel/kernel text=0x1292e78 -\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/data=0x8a1bb0+0x23ec20 -\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-syms=[0x8+0x177708\|/-+0x8+0x173ed4\|]
    Booting...
    /-\|KDB: debugger backends: ddb
    KDB: current backend: ddb
    Copyright (c) 1992-2016 The FreeBSD Project.
    Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
    	The Regents of the University of California. All rights reserved.
    FreeBSD is a registered trademark of The FreeBSD Foundation.
    FreeBSD 10.3-RELEASE-p16 #9 d88504507(RELENG_2_3_3): Wed Feb 15 11:30:33 CST 2017
        root@ce23-amd64-builder:/builder/pfsense-233/tmp/obj/builder/pfsense-233/tmp/FreeBSD-src/sys/pfSense amd64
    FreeBSD clang version 3.4.1 (tags/RELEASE_34/dot1-final 208032) 20140512
    Hyper-V Version: 10.0.14393 [SP0]
      Features: 0x2e7f <vpruntime,tmrefcnt,syncic,synctm,apic,hyercall,vpindex,reftsc,idle,tmfreq>Timecounter "Hyper-V" frequency 10000000 Hz quality 10000000
    CPU: Intel(R) Xeon(R) CPU E5-1630 v3 @ 3.70GHz (3708.12-MHz K8-class CPU)
      Origin="GenuineIntel"  Id=0x306f2  Family=0x6  Model=0x3f  Stepping=2
      Features=0xf83fbff <fpu,vme,de,pse,tsc,msr,pae,mce,cx8,apic,sep,mtrr,pge,mca,cmov,pat,pse36,mmx,fxsr,sse,sse2,ss>Features2=0xfed83203 <sse3,pclmulqdq,ssse3,fma,cx16,sse4.1,sse4.2,movbe,popcnt,aesni,xsave,osxsave,avx,f16c,rdrand,hv>AMD Features=0x2c100800 <syscall,nx,page1gb,rdtscp,lm>AMD Features2=0x21 <lahf,abm>Structured Extended Features=0x2328 <bmi1,avx2,bmi2,erms,nfpusg>XSAVE Features=0x1 <xsaveopt>Hypervisor: Origin = "Microsoft Hv"
    real memory  = 8589934592 (8192 MB)
    avail memory = 8276033536 (7892 MB)
    Event timer "LAPIC" quality 400
    ACPI APIC Table: <vrtual microsft="">random: <software, yarrow="">initialized
    ioapic0: Changing APIC ID to 0
    ioapic0 <version 1.1="">irqs 0-23 on motherboard
    wlan: mac acl policy registered
    ipw_bss: You need to read the LICENSE file in /usr/share/doc/legal/intel_ipw/.
    ipw_bss: If you agree with the license, set legal.intel_ipw.license_ack=1 in /boot/loader.conf.
    module_register_init: MOD_LOAD (ipw_bss_fw, 0xffffffff80620930, 0) error 1
    ipw_ibss: You need to read the LICENSE file in /usr/share/doc/legal/intel_ipw/.
    ipw_ibss: If you agree with the license, set legal.intel_ipw.license_ack=1 in /boot/loader.conf.
    module_register_init: MOD_LOAD (ipw_ibss_fw, 0xffffffff806209e0, 0) error 1
    ipw_monitor: You need to read the LICENSE file in /usr/share/doc/legal/intel_ipw/.
    ipw_monitor: If you agree with the license, set legal.intel_ipw.license_ack=1 in /boot/loader.conf.
    module_register_init: MOD_LOAD (ipw_monitor_fw, 0xffffffff80620a90, 0) error 1
    iwi_bss: You need to read the LICENSE file in /usr/share/doc/legal/intel_iwi/.
    iwi_bss: If you agree with the license, set legal.intel_iwi.license_ack=1 in /boot/loader.conf.
    module_register_init: MOD_LOAD (iwi_bss_fw, 0xffffffff80647c30, 0) error 1
    iwi_ibss: You need to read the LICENSE file in /usr/share/doc/legal/intel_iwi/.
    iwi_ibss: If you agree with the license, set legal.intel_iwi.license_ack=1 in /boot/loader.conf.
    module_register_init: MOD_LOAD (iwi_ibss_fw, 0xffffffff80647ce0, 0) error 1
    iwi_monitor: You need to read the LICENSE file in /usr/share/doc/legal/intel_iwi/.
    iwi_monitor: If you agree with the license, set legal.intel_iwi.license_ack=1 in /boot/loader.conf.
    module_register_init: MOD_LOAD (iwi_monitor_fw, 0xffffffff80647d90, 0) error 1
    netmap: loaded module
    kbd1 at kbdmux0
    cryptosoft0: <software crypto="">on motherboard
    padlock0: No ACE support.
    acpi0: <vrtual microsft="">on motherboard
    acpi0: Power Button (fixed)
    cpu0: <acpi cpu="">on acpi0
    attimer0: <at timer="">port 0x40-0x43 irq 0 on acpi0
    Timecounter "i8254" frequency 1193182 Hz quality 0
    Event timer "i8254" frequency 1193182 Hz quality 100
    atrtc0: <at realtime="" clock="">port 0x70-0x71 irq 8 on acpi0
    Event timer "RTC" frequency 32768 Hz quality 0
    Timecounter "ACPI-fast" frequency 3579545 Hz quality 900
    acpi_timer0: <32-bit timer at 3.579545MHz> port 0x408-0x40b on acpi0
    pcib0: <acpi host-pci="" bridge="">port 0xcf8-0xcff on acpi0
    pcib0: Length mismatch for 3 range: 20000000 vs 1fffffff
    pci0: <acpi pci="" bus="">on pcib0
    isab0: <pci-isa bridge="">at device 7.0 on pci0
    isa0: <isa bus="">on isab0
    atapci0: <intel piix4="" udma33="" controller="">port 0x1f0-0x1f7,0x3f6,0x170-0x177,0x376,0xffa0-0xffaf at device 7.1 on pci0
    ata0: <hyper-v ata="" storage="" disengage="" driver="">at channel 0 on atapci0
    ata1: <ata channel="">at channel 1 on atapci0
    pci0: <bridge>at device 7.3 (no driver attached)
    vgapci0: <vga-compatible display="">mem 0xf8000000-0xfbffffff irq 11 at device 8.0 on pci0
    vgapci0: Boot video device
    atkbdc0: <keyboard controller="" (i8042)="">port 0x60,0x64 irq 1 on acpi0
    atkbd0: <at keyboard="">irq 1 on atkbdc0
    kbd0 at atkbd0
    atkbd0: [GIANT-LOCKED]
    psm0: <ps 2="" mouse="">irq 12 on atkbdc0
    psm0: [GIANT-LOCKED]
    psm0: model IntelliMouse Explorer, device ID 4
    uart0: <16550 or compatible> port 0x3f8-0x3ff irq 4 flags 0x10 on acpi0
    uart0: console (115200,n,8,1)
    uart1: <16550 or compatible> port 0x2f8-0x2ff irq 3 on acpi0
    fdc0: <floppy drive="" controller="" (fde)="">port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on acpi0
    fd0: <1440-KB 3.5" drive> on fdc0 drive 0
    vmbus0: <vmbus devices="">irq 5,7 on acpi0
    orm0: <isa option="" rom="">at iomem 0xc0000-0xcbfff on isa0
    sc0: <system console="">at flags 0x100 on isa0
    sc0: VGA <16 virtual consoles, flags=0x300>
    vga0: <generic isa="" vga="">at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
    ppc0: cannot reserve I/O port range
    Timecounters tick every 1.000 msec
    random: unblocking device.
    cd0 at ata1 bus 0 scbus0 target 0 lun 0
    cd0: <msft virtual="" cd="" rom="" 1.0="">Removable CD-ROM SPC-3 SCSI device
    Timecounter "TSC-low" frequency 1854059029 Hz quality 800
    Event timer "HyperV" frequency 10000000 Hz quality 1000
    cd0: 16.700MB/s transfers (storvsc0 on vmbus0
    WDMA2, ATAPI 12bytes, PIO 65534bytes)hyperv-utils0 on vmbus0
    hyperv-utils0: Hyper-V Service attaching: Hyper-V Heartbeat Service
    
    hyperv-utils1 on vmbus0
    hyperv-utils1: Hyper-V Service attaching: Hyper-V KVP Service
    
    hyperv-utils2 on vmbus0
    hyperv-utils2: Hyper-V Service attaching: Hyper-V Shutdown Service
    
    cd0: Attempt to query device size failed: NOT READY, Medium not present
    hyperv-utils3 on vmbus0
    hyperv-utils3: Hyper-V Service attaching: Hyper-V Time Synch Service
    
    storvsc1 on vmbus0
    (probe0:blkvsc0:0:0:0): storvsc scsi_status = 2
    hn0: <synthetic network="" interface="">on vmbus0
    da0 at blkvsc0 bus 0 scbus1 target 0 lun 0
    da0: <msft virtual="" disk="" 1.0="">Fixed Direct Access SPC-3 SCSI device
    da0: 300.000MB/s transfers
    da0: Command Queueing enabled
    da0: 20480MB (41943040 512 byte sectors)
    hn0: unknown status 1073872902 received
    hn0: unknown status 1073872902 received
    hn0: hv send offload request succeeded
    hn0: Using defaults for TSO: 65518/35/2048
    hn0: Ethernet address: 00:15:5d:1e:3c:01
    hn1: <synthetic network="" interface="">on vmbus0
    hn1: unknown status 1073872902 received
    hn1: unknown status 1073872902 received
    hn1: hv send offload request succeeded
    hn1: Using defaults for TSO: 65518/35/2048
    hn1: Ethernet address: 00:15:5d:1e:3c:02
    Trying to mount root from ufs:/dev/ufsid/590ace5d49445e13 [rw]...
    Configuring crash dumps...
    Using /dev/label/swap0 for dump device.
    /dev/ufsid/590ace5d49445e13: FILE SYSTEM CLEAN; SKIPPING CHECKS
    /dev/ufsid/590ace5d49445e13: clean, 2896551 free (495 frags, 362007 blocks, 0.0% fragmentation)
    Filesystems are clean, continuing...
    Mounting filesystems...
    
         ___
     ___/ f \
    / p \___/ Sense
    \___/   \
        \___/
    
    Welcome to pfSense 2.3.3-RELEASE on the 'pfSense' platform...
    
    No core dumps found.
    Creating symlinks......ELF ldconfig path: /lib /usr/lib /usr/lib/compat /usr/local/lib /usr/local/lib/ipsec /usr/local/lib/perl5/5.24/mach/CORE
    32-bit compatibility ldconfig path: /usr/lib32
    done.
    External config loader 1.0 is now starting... da0s1 da0s1a da0s1b
    Launching the init system....... done.
    Initializing.................. done.
    Starting device manager (devd)...done.
    Loading configuration......done.
    Updating configuration...done.
    Cleaning backup cache...............done.
    Setting up extended sysctls...done.
    Setting timezone...done.
    Configuring loopback interface...done.
    Starting syslog...done.
    Starting Secure Shell Services...done.
    Setting up polling defaults...May  4 00:24:51  syslogd: /var/log/routing.log: Operation not supported by device
    
    May  4 00:24:51  syslogd: /var/log/ntpd.log: Operation not supported by device
    
    May  4 00:24:51  syslogd: /var/log/ppp.log: Operation not supported by device
    
    May  4 00:24:51  syslogd: /var/log/poes.log: Operation not supported by device
    
    May  4 00:24:51  syslogd: /var/log/l2tps.log: Operation not supported by device
    
    done.
    May  4 00:24:51  syslogd: /var/log/ipsec.log: Operation not supported by device
    
    Setting up interfaces microcode...May  4 00:24:51  syslogd: /var/log/openvpn.log: Operation not supported by device
    
    done.
    May  4 00:24:51  syslogd: /var/log/gateways.log: Operation not supported by device
    
    May  4 00:24:51  syslogd: /var/log/resolver.log: Operation not supported by device
    
    May  4 00:24:51  syslogd: /var/log/dhcpd.log: Operation not supported by device
    
    May  4 00:24:51  syslogd: /var/log/relayd.log: Operation not supported by device
    
    May  4 00:24:51  syslogd: /var/log/wireless.log: Operation not supported by device
    
    Configuring loopback interface...May  4 00:24:51  syslogd: /var/log/filter.log: Operation not supported by device
    
    done.
    May  4 00:24:51  syslogd: /var/log/vpn.log: Operation not supported by device
    
    Creating wireless clone interfaces...May  4 00:24:51  syslogd: /var/log/portalauth.log: Operation not supported by device
    
    May  4 00:24:51  syslogd: /var/log/nginx.log: Operation not supported by device
    
    done.
    May  4 00:24:51  syslogd: /var/log/dhcpd.log: Operation not supported by device
    
    Configuring LAGG interfaces...done.
    May  4 00:24:51  syslogd: /var/log/system.log: Operation not supported by device
    
    Configuring VLAN interfaces...done.
    Configuring QinQ interfaces...done.
    Configuring WAN interface...done.
    Configuring LAN interface...done.
    Configuring CARP settings...done.
    Syncing OpenVPN settings...done.
    Configuring firewall......done.
    Starting PFLOG...done.
    Setting up gateway monitors...done.
    Starting DNS Resolver...done.
    Synchronizing user settings...done.
    Starting webConfigurator...done.
    Configuring CRON...done.
    Starting NTP time client...done.
    Starting DHCPv6 service...done.
    Configuring firewall......done.
    Generating RRD graphs...done.
    Starting syslog...done.
    May  4 00:25:58  syslogd: /var/log/routing.log: Operation not supported by device
    
    Starting CRON... May  4 00:25:58  syslogd: /var/log/ntpd.log: Operation not supported by device
    
    May  4 00:25:58  syslogd: /var/log/ppp.log: Operation not supported by device
    
    May  4 00:25:58  syslogd: /var/log/poes.log: Operation not supported by device
    
    done.
    May  4 00:25:58  syslogd: /var/log/l2tps.log: Operation not supported by device
    
    May  4 00:25:58  syslogd: /var/log/ipsec.log: Operation not supported by device
    
    May  4 00:25:58  syslogd: /var/log/openvpn.log: Operation not supported by device
    
    May  4 00:25:58  syslogd: /var/log/gateways.log: Operation not supported by device
    
    May  4 00:25:58  syslogd: /var/log/resolver.log: Operation not supported by device
    
    May  4 00:25:58  syslogd: /var/log/dhcpd.log: Operation not supported by device
    
    May  4 00:25:58  syslogd: /var/log/relayd.log: Operation not supported by device
    
    May  4 00:25:58  syslogd: /var/log/wireless.log: Operation not supported by device
    
    May  4 00:25:58  syslogd: /var/log/filter.log: Operation not supported by device
    
    May  4 00:25:58  syslogd: /var/log/vpn.log: Operation not supported by device
    
    May  4 00:25:58  syslogd: /var/log/portalauth.log: Operation not supported by device
    
    May  4 00:25:58  syslogd: /var/log/nginx.log: Operation not supported by device
    
    May  4 00:25:58  syslogd: /var/log/dhcpd.log: Operation not supported by device
    
    May  4 00:25:58  syslogd: /var/log/system.log: Operation not supported by device
    
    pfSense (pfSense) 2.3.3-RELEASE amd64 Thu Feb 16 06:59:53 CST 2017
    Bootup complete
    
    FreeBSD/amd64 (pfSense.localdomain) (ttyu0)
    
    *** Welcome to pfSense 2.3.3-RELEASE (amd64 full-install) on pfSense ***
    
     WAN (wan)       -> hn1        -> 
     LAN (lan)       -> hn0        -> v4: 10.30.30.6/24
    
     0) Logout (SSH only)                  9) pfTop
     1) Assign Interfaces                 10) Filter Logs
     2) Set interface(s) IP address       11) Restart webConfigurator
     3) Reset webConfigurator password    12) PHP shell + pfSense tools
     4) Reset to factory defaults         13) Update from console
     5) Reboot system                     14) Disable Secure Shell (sshd)
     6) Halt system                       15) Restore recent configuration
     7) Ping host                         16) Restart PHP-FPM
     8) Shell
    
    Enter an option:</synthetic></msft></synthetic></msft></generic></system></isa></vmbus></floppy></ps></at></keyboard></vga-compatible></bridge></ata></hyper-v></intel></isa></pci-isa></acpi></acpi></at></at></acpi></vrtual></software></version></software,></vrtual></xsaveopt></bmi1,avx2,bmi2,erms,nfpusg></lahf,abm></syscall,nx,page1gb,rdtscp,lm></sse3,pclmulqdq,ssse3,fma,cx16,sse4.1,sse4.2,movbe,popcnt,aesni,xsave,osxsave,avx,f16c,rdrand,hv></fpu,vme,de,pse,tsc,msr,pae,mce,cx8,apic,sep,mtrr,pge,mca,cmov,pat,pse36,mmx,fxsr,sse,sse2,ss></vpruntime,tmrefcnt,syncic,synctm,apic,hyercall,vpindex,reftsc,idle,tmfreq> 
    


  • Reinstall resolved issue.  I think I shut it down improperly once during initial install.


Log in to reply