Ipv6 down

[yon]

@doktornotor:

Hmmm, so there's actually nothing wrong with IPv6 except that your unknown Windows version does not get IPv6 assigned via DHCP? Well you do not need DHCPv6 at all in the first place. I'd suggest to switch RADVD to Assisted or Unmanaged.

yes. just it is Assisted. but ipv6 not normal work.

2.4.0-RC (amd64)
built on Tue Aug 29 09:29:29 CDT 2017

tracert 2a04:b900:0:37

1  2003 ms    1 ms    1 ms  face.x.net [2001:470:x:1089::20]
  2    *        *        *    time out。
  3    *        *        *    time out。
  4    *        *        *    time out。
  5    *        *        *    time out。
  6    *        *        *    time out。
  7    *        *        *    time out。
  8    *        *        *    time out。
  9    *        *        *    time out。
10    *        *        *    time out。
11    *        *        *    time out。
12    *        *        *    time out。
13    *        *        *    time out。
14    *        *        *    time out。
15    *        *        *    time out。
16    *        *        *    time out。
17    *        *        *    time out。
18    *        *        *    time out。
19    *        *        *    time out。
20    *        *        *    time out。
21    *        *        *    time out。
22    *        *        *    time out。
23    *        *        *    time out。
24    *        *        *    time out。
25    *        *        *    time out。
26    *        *        *    time out。
27    *        *        *    time out。
28    *        *        *    time out。
29    *        *        *    time out。
30    *        *        *    time out。


[doktornotor]

You should probably troubleshoot your "not normal work" with Microsoft.

May I at least suggest posting on the international section of the forums, because I cannot see this going anywhere when English is used.

[yon]

i have three he.ne tunnel, only an tunnel gif is up. other gif tunnel is down.

only the pf localhost ipv6 can tracert to internet. lan's hosts can't.

i have send mail he.net support.

he reply

Tunnels are stateless so make certain your IPv4 endpoints are up to date in our system and that no filtering is happening by your ISP or any configuration on your systems.

Both tunnel IDs are showing they are properly configured on our end, however I'm not seeing counters increment on either.


[doktornotor]

I have no idea how are you having 3 HE tunnels on a single box. Last time I checked it was completely impossible to create another tunnel to WAN IPv4 that's already been configured in another existing tunnel. Sounds very much like a completely broken setup, additionally unsupported by HE as well.

[yon]

@doktornotor:

I have no idea how are you having 3 HE tunnels on a single box. Last time I checked it was completely impossible to create another tunnel to WAN IPv4 that's already been configured in another existing tunnel. Sounds very much like a completely broken setup, additionally unsupported by HE as well.

i had used 3 tunnel years .  i have 3 ip wan.

[doktornotor]

Well, good luck with that.

[grandrivers]

you need to make sure you have unique gateways for each tunnel

[yon]

DHCPv6 Server  not work. no push ipv6 gateway to lan's client.

[yon]

@yon:

DHCPv6 Server  not work. no push ipv6 gateway to lan's client.

client can't get default ipv6 gateway ip.

[doktornotor]

DHCPv6 is not the thing that's pushing GWs. You need RA enabled.

[yon]

@doktornotor:

DHCPv6 is not the thing that's pushing GWs. You need RA enabled.

of cause, i have enabled RA. it is can get DNS server, but can't get default ipv6 gateway

[yon]

@doktornotor:

DHCPv6 is not the thing that's pushing GWs. You need RA enabled.

i find the Router Advertisement Daemon can't start.

log show :

servicewatchdog_cron.php: The command '/usr/local/sbin/radvd -p /var/run/radvd.pid -C /var/etc/radvd.conf -m syslog' returned exit code '1', the output was ''
servicewatchdog_cron.php: Service Watchdog detected service radvd stopped. Restarting radvd (Router Advertisement Daemon)


[yon]

Router Advertisement Daemon

[doktornotor]

1/ Remove the RADVD service from service watchdog!
2/ Kindly configure your gateway monitoring so that it reflects your super-sucky connectivity which results in RTTs in 300+ms range so that it does not think one of your zillion WANs went down every couple of minutes. Or disable the monitoring altogether.

[yon]

@doktornotor:

1/ Remove the RADVD service from service watchdog!
2/ Kindly configure your gateway monitoring so that it reflects your super-sucky connectivity which results in RTTs in 300+ms range so that it does not think one of your zillion WANs went down every couple of minutes. Or disable the monitoring altogether.

i have do it.  but the RADVD service still can't start.

73688 /status_services.php: The command '/usr/local/sbin/radvd -p /var/run/radvd.pid -C /var/etc/radvd.conf -m syslog' returned exit code '1', the output was ''

[yon]

@yon:

@doktornotor:

1/ Remove the RADVD service from service watchdog!
2/ Kindly configure your gateway monitoring so that it reflects your super-sucky connectivity which results in RTTs in 300+ms range so that it does not think one of your zillion WANs went down every couple of minutes. Or disable the monitoring altogether.

i have do it.  but the RADVD service still can't start.

73688 /status_services.php: The command '/usr/local/sbin/radvd -p /var/run/radvd.pid -C /var/etc/radvd.conf -m syslog' returned exit code '1', the output was ''

i have no the file  in system /var/run/radvd.pid

[xpxp2002]

I've been having this issue for a few weeks now, as well. Only using one WAN. The radvd process seems to start on bootup, but the first boot after an upgrade it seems to not function. Restarting radvd or rebooting seems to fix.

[yon]

@xpxp2002:

I've been having this issue for a few weeks now, as well. Only using one WAN. The radvd process seems to start on bootup, but the first boot after an upgrade it seems to not function. Restarting radvd or rebooting seems to fix.

my radvd service cant start. i dont know why

[Guest]

@yon:

@xpxp2002:

I've been having this issue for a few weeks now, as well. Only using one WAN. The radvd process seems to start on bootup, but the first boot after an upgrade it seems to not function. Restarting radvd or rebooting seems to fix.

my radvd service cant start. i dont know why

Can you post your radvd.conf, or at least examine it to confirm that it is correct.

[yon]

Automatically Generated, do not edit

Generated for DHCPv6 Server lan

interface re0 {
AdvSendAdvert on;
MinRtrAdvInterval 3;
MaxRtrAdvInterval 20;
AdvLinkMTU 1500;
AdvDefaultPreference high;
AdvManagedFlag on;
AdvOtherConfigFlag on;
prefix 2001:470:f165::/48 {
DeprecatePrefix on;
AdvOnLink on;
AdvAutonomous on;
AdvRouterAddr on;
AdvValidLifetime 86400;
AdvPreferredLifetime 14400;
};
prefix 2001:470:f165:1/64 {
DeprecatePrefix on;
AdvOnLink on;
AdvAutonomous on;
AdvRouterAddr on;
};
route ::/0 {
RemoveRoute on;
};
RDNSS 2001:470:f167::8 2001:470:f165::6 { };
DNSSL xoyu.net  { };
};

Generated for DHCPv6 Server opt8

interface gif3 {
AdvSendAdvert on;
MinRtrAdvInterval 5;
MaxRtrAdvInterval 20;
AdvLinkMTU 1480;
AdvDefaultPreference medium;
prefix 2001:470:d:1085::20/128 {
DeprecatePrefix on;
AdvValidLifetime 86400;
AdvPreferredLifetime 14400;
};
route ::/0 {
RemoveRoute on;
};
RDNSS 2a05:dfc7:5::53 2001:19f0:7402:d:5400:00ff:fe2a:7fb6 2001:41d0:8:be92::1 fd42:d42:d42:53::1 { };
DNSSL xoyu.net  { };
};