Don't upgrade to x86 CE build 2.4.0.r.20171008.0625
-
Reinstalled from the previous release (yesterday). It's back up.
-
For me, DHCPd and DNSmask service don't start.
Go back
-
Ditto. Updated from yesterday’s build and the router is no longer accessible remotely and network is down.
-
Completely borked me as well, AMD-64 version
-
I see also, at pfsense boot : block on "db> " a power off, and after, it's ok for me
-
Hmm, like no static IP on the LAN interface?
I just upgraded a box here and am not seeing that.
Logging is working as the files were already present. There may be an issue on fresh installs from that snap.
What exactly are you seeing? Anything logged?
Steve
For me, when it came back up, LAN and WAN both had the interfaces listed correct, but no IPs listed. Reboot did not help.
I did update via the webgui. Mine is also AMD64.I blew it away (testing VM), and did a fresh install of today's build, and so far everything seems good.
-
I'll try to give as much information as possible:
Box before the upgrade attempt:
Mini-ITX System based on an ASUS N3150-C with an Intel 82571EB 4 port NIC (em driver) and 64GB SSD.
Onboard Realtek Ethernet Controller disabled in BIOS.
It was running the last 2.4RC build from yesterday (07.10.2017) using ZFS as filesystem.
Note: I was originally running 2.4.1 and reverted back to 2.4.0, when it moved to FreeBSD 11.1, recovering the config during the install.Installed Packages iperf (server not active), bandwidthd and cron.
em0 configured as LAN with a static IPv4 on 192.168.2.1/24 and the IPv6 from HE.net tunnel.
em1 confgured as OPT with a static IPv4 on 192.168.1.1/24 to access the WebUI of the DSL modem.
WAN configured as PPPoE on em1, get's a dynamic IPv4 address.I started the upgrade using the WebUI, like always, it downloaded the packages and rebootet. Booting took quite a bit longer than usual, after it was finished neither the box nor the WAN was reachable.
I attached a Monitor to the box and normal output should be like this:
WAN (wan) -> pppoe0 -> v4/PPPoE: x.x.x.x Lan (lan) -> em0 -> v4: 192.168.2.1/24 v6: x:x:x:x::x/64 MODEM_ACCESS (opt1) -> em1 -> v4: 192.168.1.2/24 and the HE.NET Tunnel
instead it was this:
WAN (wan) -> pppoe0 -> Lan (lan) -> em0 -> v6: x:x:x:x::x/64 MODEM_ACCESS (opt1) -> em1 -> and the HE.NET Tunnel
I attached a keyboard and used option 2 to give LAN a new IPv4 address, the process run without displaying any errors but LAN was still without an IPv4 address afterwards. I rebooted for good measure but that didn't change a thing.
After that I used option 4 to reset pfSense to factory defaults, this run through without an error and after the reboot this was displayed for the interfaces:WAN (wan) -> em0 -> Lan (lan) -> em1 ->
I tried to reassign the interfaces and manually add an IPv4 address to the LAN, but it still didn't work. So I reinstalled an older build and go the box working again.
-
Same here, BUT if helps to solve i had several IP alias in LAN and they were asigned to LAN and worked to connect.
Then deleted them and unable to configure the IP.
Also in WAN i have static IP and even i configure it, it is not used (in console, IP (WAN and LAN) are blank (in Web cfg (when accessed with one of those aliases) appeared as configured)
Also when configuring in console appears an error about "renaming interfaces", i'll try to take a photo.
Downloading 20171006-1536 to reinstall if no solution given.
-
I blew it away (testing VM), and did a fresh install of today's build, and so far everything seems good.
Did you restore you previous config or did you reconfigure by hand?
Are you using the traffic shaper, and if yes do the queues show up in Status -> Queues?
-
-
I blew it away (testing VM), and did a fresh install of today's build, and so far everything seems good.
Did you restore you previous config or did you reconfigure by hand?
Are you using the traffic shaper, and if yes do the queues show up in Status -> Queues?
No, I did everything from scratch again (only installed about 9:00pm EDT). I didn't have the shaper setup, I did have a few packages (ACME, FRR, Snort, PFBlockerNG), and I believe I went through the real basic setup of Snort and PFBlockerNG. But other than that it was pretty much stock/not configured.
I still have the ISOs from yesterday and I can do some testing to see if I can reproduce it and grab some more screen shots.
Edit: So far I reinstalled with yesterday's build, but it isn't finding anything yet for an update. I'll leave it be for a bit and see what happens.
-
I tried to configure the IPs from shell (console) and default GW and got some connectivity
So:
ifconfig re0 WANIP/Mask
ifconfig rl0 LANIP/Mask
route add default MI_ISP_GW_IPGave me some connectivity, i can ping to the Internet (ie: 8.8.8.8 ) BUT no DNS (even configured in Web manager, i had to configure the GW for DNS again)
Now restoring a config over this build (i did a backup yesterday night! ::) ) and will report if solves something
-
This is superborked and not being able to see the relevant commits on Redmine/GitHub once again does not help here.
-
See the other thread: https://forum.pfsense.org/index.php?topic=137672.msg752884#msg752884
It's been pulled.
-
We're working on a fix right now. A change went in that appears to have broken older package binaries (even base system package binaries) with a newer kernel/world. Once we get a new full pkg set built and tested we'll get a fix out.
In the meantime, installing a current snapshot fresh will work since it all matches. Reinstalling and using the "recover config.xml" option will have you back up with less effort than other solutions.
We have taken the broken package sets down so people can't accidentally upgrade to a broken snapshot.
-
We have taken the broken package sets down so people can't accidentally upgrade to a broken snapshot.
for some reason I am unable to get to the repository after going to previous snapshot. Is there anyway I can quickly install freeradius package so I get wifi working atleast?
-
The repos are down apparently ATM.
-
-
Yes, my pfSense box got hosed as well. I can't complete my restore since the pkg libraries are down.
Can we restore the latest packages that worked for 2.4.0 while the devs fix the package set?
-
Yes, my pfSense box got hosed as well. I can't complete my restore since the pkg libraries are down.
Can we restore the latest packages that worked for 2.4.0 while the devs fix the package set?
Yes please restore the packages
edit:
it seems they added .BAD to the end of the repos.
https://firmware.netgate.com/pkg/pfSense_factory-v2_4_0_amd64-core.BAD
https://firmware.netgate.com/pkg/pfSense_factory-v2_4_0_amd64-pfSense_factory-v2_4_0.BADCan someone test this /usr/local/etc/pkg/repos/pfSense.conf file?
FreeBSD: { enabled: no } pfSense-core: { url: "pkg+https://pkg.pfsense.org/pfSense_v2_4_0_amd64-core.BAD", mirror_type: "srv", signature_type: "fingerprints", fingerprints: "/usr/local/share/pfSense/keys/pkg", enabled: yes } pfSense: { url: "pkg+https://pkg.pfsense.org/pfSense_v2_4_0_amd64-pfSense_v2_4_0.BAD", mirror_type: "srv", signature_type: "fingerprints", fingerprints: "/usr/local/share/pfSense/keys/pkg", enabled: yes }
edit 2: works!