2.4.4 fails upgrade and fresh installation
jbhowlesr last edited by jbhowlesr
When I try install 2.4.4, the installer fails with a repeated register dump
I tried the upgrade from 2.4.3_1 to 2.4.4 first but received the above and it just keep spitting this out repeatedly. So moved to fresh install and received the same.
I tried setting the bios for UEFI only with no luck. I tried disabling CSM altogether and still getting the same
My box is a Kaby Lake Celeron based with 6 Intel 1gb NIC ports and I’m using an msata SSD.
I tried reverting to 2.4.3_1 which installs fine but snort and pfblocker have been updated and they cause 2.4.3_1 to crash.
That looks like a problem with your disk controller, or its driver. But it's referring to sdhci which is generally for mmc/eMMC not for mSATA disks.
We had some issues similar to that with eMMC on certain devices with 2.4.4, the driver in FreeBSD 11.2 was trying to use a different mode than before, and the driver didn't get along too well with that.
You might search around and see if anyone else on FreeBSD has a matching chipset issue to yours. There may be a workaround specific to your hardware.
@jimp the board is a system on chip Celeron 3865U which is 7th generation and supports AES-NI. The board doesn’t have a chipset to my knowledge since it’s an SoC. The board itself is a Pico ITX I believe or the size just above.
I did reach out to the board maker to ask for a bios update. That’s the only thing that strikes me as a possibility.
@jimp tried switching to a standard sata based hard drive while disabling PCIe altogether with zero luck. Not sure what else to do at this point. Bout ready to give up and go to a different software set to use like Untangle or Sophos. This 2.4.4 update has rendered my unit unusable with pfsense because even if I revert to the previous version of this software, the utilities I prefer to run have been updated and will not run on the previous version of pfsense. So, I feel like this stuff should have been properly vetted before launching such drastic system update. There is literally no reason my hardware shouldn't be support in 2.4.4. Especially since it is secure boot capable and compliant with Windows 10 ver 1709 and MS Intune. The issue to me seems like a driver issue with something included in 2.4.4. UEFI is fully enabled in this systems bios by default so I am of mind that there is no issue with my hardware.
Still waiting for some resolution here but it is starting to feel like none is coming.
We cannot possibly test every combination of hardware we do not sell. 2.4.4 was in beta for a very long time. At any point you could have tested it out on that hardware.
Additionally, the problem appears to be a FreeBSD compatibility issue -- something which we do not have any control over.
Try to replicate the problem on FreeBSD 11.2 and open an issue upstream with FreeBSD if/when the problem still happens there.
The error you show appears to be from mmc/eMMC like I said and not a SATA/mSATA/m.2 disk, so it's also possible that is something you need to disable on the board or in the BIOS, or find a FreeBSD device hint that matches your hardware to put in at the loader prompt to disable the controller (like
hint.sdhci.0.disable=1) or maybe some other related tunable like
hw.sdhci.enable_msi=0or some combination of
quirk_clear, see https://bugs.freebsd.org/bugzilla/show_bug.cgi?id=228340 )
@jimp The problem, I never get far enough to do any of this. The images above is what happens when I try to fresh install. The system simply never starts the installation and therefor no console options appear. Even if I upgrade and reboot, what is shown in the photo occurs in the boot and pfsense never starts up. Essentially, the system is prevented from even loading or installing.
You can add those to
/boot/loader.conf.localbefore upgrading, or either way you can do that at a loader prompt. At the boot menu, choose the loader prompt option. If no boot menu shows up, press space when you see the loader spinner (
@jimp Sorry for the extreme delay in getting back to you. Let make sure I got this correct. Go to fresh install and when I see the spinning (|), press space to bring up a prompt and type /boot/loader.conf.local? I'm not familiar with the command line side of pfsense but if you can explain this a little further that would be great. I've been using untangle for the last month because I am unable to load 2.4.4 and I'm itching to get back to pfsense. Is there some other screen shots I can post to help the troubleshooting process out?
If you are coming from 2.4.3 you can just add those values to the file
/boot/loader.conf.localbefore you upgrade. You may need to create that file.
If you are installing 2.4.4 fresh, or have already upgraded and it won't boot, you need to set those values at the loader prompt in order to allow it to boot and then add them to the file.
That process is detailed here for disabling ACPI but obviously you would want to disable sdhci instead:
Let us know if that helps. That has worked for others in your situation though.
Looking at the actual error you're seeing you might also try: