Je ne peux pas sortir avec ces règles …

Gertjan

Pour voir ce qui ce passe, il suffit de regarder dans les logs !
Status => System logs => System.

En plus, j'utilise un logger (Kiwi) sur un des mes PC's 'LAN' pour logger en permanence les événements de pfSense. C'est quasi indispensable tout façon, mon pfSense n'a pas de clavier, ni écran depuis des années déjà - c'est un boite dans un armoire informatique)

Il faut lire cette liste de BAS (événement le plus vieux) vers le HAUT (plus récent) !
J'ai coupé dans mes logs la séquence qui montre la connexion par PPPOE (mon FAI est Orange - je n'utilise PAS un LiveBox mais un Speedtouch 540 en mode Bridge ~ PPPOE)

…..

Tout est UP de nouveau - le tout prend env. 5 secondes.

mpd: [pppoe] IFACE: Up event
mpd: [pppoe] exec: /usr/local/sbin/ppp-linkup ng0 inet 86.201.236.45 86.201.236.1 fti/xxxxxx dns1 80.10.246.130 dns2 81.253.149.10
mpd: [pppoe] exec: /sbin/route add 0.0.0.0 86.201.236.1
mpd: [pppoe] exec: /sbin/route add 86.201.236.45 -iface lo0
mpd: [pppoe] exec: /sbin/ifconfig ng0 86.201.236.45 86.201.236.1 netmask 0xffffffff -link0
mpd: [pppoe] setting interface ng0 MTU to 1492 bytes
mpd: [pppoe] IFACE: Up event
mpd: 86.201.236.45 -> 86.201.236.1
mpd: [pppoe] IPCP: LayerUp
mpd: [pppoe] IPCP: state change Ack-Rcvd –> Opened
mpd: IPADDR 86.201.236.1
mpd: [pppoe] IPCP: SendConfigAck #15
mpd: 86.201.236.1 is OK
mpd: IPADDR 86.201.236.1
mpd: [pppoe] IPCP: rec'd Configure Request #15 link 0 (Ack-Rcvd)
mpd: [pppoe] IPCP: state change Req-Sent –> Ack-Rcvd
mpd: SECDNS 81.253.149.10
mpd: PRIDNS 80.10.246.130
mpd: IPADDR 86.201.236.45
mpd: [pppoe] IPCP: rec'd Configure Ack #8 link 0 (Req-Sent)
mpd: SECDNS 81.253.149.10
mpd: PRIDNS 80.10.246.130
mpd: IPADDR 86.201.236.45
mpd: [pppoe] IPCP: SendConfigReq #8
mpd: SECDNS 81.253.149.10
mpd: PRIDNS 80.10.246.130
mpd: 86.201.236.45 is OK
mpd: IPADDR 86.201.236.45
mpd: [pppoe] IPCP: rec'd Configure Nak #7 link 0 (Req-Sent)
mpd: SECDNS 0.0.0.0
mpd: PRIDNS 0.0.0.0
mpd: IPADDR 0.0.0.0
mpd: [pppoe] IPCP: SendConfigReq #7
mpd: COMPPROTO VJCOMP, 16 comp. channels, no comp-cid
mpd: [pppoe] IPCP: rec'd Configure Reject #6 link 0 (Req-Sent)
mpd: SECDNS 0.0.0.0
mpd: PRIDNS 0.0.0.0
mpd: COMPPROTO VJCOMP, 16 comp. channels, no comp-cid
mpd: IPADDR 0.0.0.0
mpd: [pppoe] IPCP: SendConfigReq #6
mpd: [pppoe] error writing len 32 frame to bypass: Network is down
mpd: SECDNS 0.0.0.0
mpd: PRIDNS 0.0.0.0
mpd: COMPPROTO VJCOMP, 16 comp. channels, no comp-cid
mpd: IPADDR 0.0.0.0
mpd: [pppoe] IPCP: SendConfigReq #5
mpd: [pppoe] IPCP: state change Starting –> Req-Sent
mpd: [pppoe] IPCP: Up event
mpd: [pppoe] up: 1 link, total bandwidth 64000 bps
mpd: [pppoe] setting interface ng0 MTU to 1492 bytes
mpd: [pppoe] LCP: phase shift AUTHENTICATE –> NETWORK
mpd: [pppoe] LCP: authorization successful
mpd: MESG: CHAP authentication success, unit 8963
mpd: [pppoe] CHAP: rec'd SUCCESS #1
mpd: [pppoe] CHAP: sending RESPONSE
mpd: Using authname "fti/xxxxxx"
mpd: Name: "BSBPN168"
mpd: [pppoe] CHAP: rec'd CHALLENGE #1
mpd: [pppoe] LCP: LayerUp
mpd: [pppoe] LCP: auth: peer wants CHAP, I want nothing
mpd: [pppoe] LCP: phase shift ESTABLISH –> AUTHENTICATE
mpd: [pppoe] LCP: state change Ack-Sent –> Opened
mpd: MAGICNUM 714f6e00
mpd: MRU 1492
mpd: [pppoe] LCP: rec'd Configure Ack #3 link 0 (Ack-Sent)
mpd: [pppoe] LCP: state change Req-Sent –> Ack-Sent
mpd: MAGICNUM 16323199
mpd: AUTHPROTO CHAP MD5
mpd: MRU 1492
mpd: [pppoe] LCP: SendConfigAck #171
mpd: MAGICNUM 16323199
mpd: AUTHPROTO CHAP MD5
mpd: MRU 1492
mpd: [pppoe] LCP: rec'd Configure Request #171 link 0 (Req-Sent)
mpd: MAGICNUM 714f6e00
mpd: MRU 1492
mpd: [pppoe] LCP: SendConfigReq #3
mpd: [pppoe] LCP: phase shift DEAD –> ESTABLISH
mpd: [pppoe] LCP: state change Starting –> Req-Sent
mpd: [pppoe] LCP: Up event
mpd: [pppoe] link: origination is local
mpd: [pppoe] link: UP event
mpd: [pppoe] device is now in state UP
mpd: [pppoe] device: UP event in state OPENING
mpd: [pppoe] PPPoE connection successful
mpd: [pppoe] rec'd ACNAME "BSBOR158-B2234340702746"
mpd: [pppoe] device is now in state OPENING
mpd: [pppoe] device: OPEN event in state DOWN
mpd: [pppoe] LCP: LayerStart
mpd: [pppoe] LCP: state change Initial –> Starting
mpd: [pppoe] LCP: Open event
mpd: [pppoe] link: OPEN event
mpd: [pppoe] opening link "pppoe"…
mpd: [pppoe] device is now in state DOWN
mpd: [pppoe] device: CLOSE event in state DOWN
mpd: [pppoe] LCP: LayerFinish
mpd: [pppoe] LCP: state change Starting –> Initial
mpd: [pppoe] LCP: Close event
mpd: [pppoe] link: CLOSE event
mpd: [pppoe] closing link "pppoe"…
mpd: [pppoe] device is now in state DOWN
mpd: [pppoe] pausing 6 seconds before open

Tout est down : 6 sec de pause.

mpd: [pppoe] device: OPEN event in state DOWN
mpd: [pppoe] LCP: phase shift TERMINATE –> DEAD
mpd: [pppoe] LCP: state change Stopping –> Starting
mpd: [pppoe] LCP: Down event
mpd: [pppoe] link: DOWN event
mpd: [pppoe] device is now in state DOWN
mpd: [pppoe] device: DOWN event in state UP
mpd: [pppoe] PPPoE connection closed
mpd: [pppoe] LCP: LayerDown
mpd: [pppoe] LCP: SendTerminateAck #2
mpd: [pppoe] exec: /sbin/ifconfig ng0 down delete -link0
mpd: [pppoe] exec: /sbin/route delete 86.201.109.188 -iface lo0
mpd: [pppoe] exec: /sbin/route delete 0.0.0.0 86.201.109.1
mpd: [pppoe] IFACE: Down event
mpd: [pppoe] IPCP: LayerDown
mpd: [pppoe] IPCP: state change Opened –> Starting
mpd: [pppoe] IPCP: Down event
mpd: [pppoe] up: 0 links, total bandwidth 9600 bps
mpd: [pppoe] setting interface ng0 MTU to 1500 bytes
mpd: [pppoe] LCP: phase shift NETWORK –> TERMINATE
mpd: [pppoe] LCP: state change Opened –> Stopping
mpd: [pppoe] LCP: rec'd Terminate Request #6 link 0 (Opened)

La connection existe, mon FAI m'informe qu'il va couper le PPPOE

….

C'est beau tout ça non ?

Pour tester si ton modem est bien dans le bon mode, c'est très simple !
Il suffit de tester avec un PC Windows, car Windows sais faire le PPPOE aussi tout seul !

[Mon exemple ici est valable pour un XP Pro - Home est la même manip je pense, un équivalent existe pour Vista, MAC, etc]

Branche donc le PC directement sur le modem.
Et on y go : Démarrer => Connexions => Afficher toutes les connexions
Créer une nouvelle connexion.
Établir une nouvelle connexion.
Configurer une nouvelle connexion
Se connecter en utilisent une connexion large bande qui nécessite un nom d'utilisateur et un mot de passe
Donne un nom au Hazard - ie "Mobistar" sera ok - valide
Donne nom utilisateur et mot de passe (pour toi xxxx@mobistar et xxx)
Laisse les deux options coché.
Valide.
T'est connecté !! [ SI ton modem est bien en mode PPPOE et que ton FAI supporte cette façon de ce connecter]