Can ping IPv6 from LAN but not from firewall itself
-
How exactly are you testing this?
[2.4.4-RELEASE][root@sg4860.local.lan]/root: ping6 ipv6.google.com PING6(56=40+8+8 bytes) 2001:470:<snipped>::2 --> 2607:f8b0:4002:c09::66 16 bytes from 2607:f8b0:4002:c09::66, icmp_seq=0 hlim=48 time=56.963 ms 16 bytes from 2607:f8b0:4002:c09::66, icmp_seq=1 hlim=48 time=47.911 ms -
@johnpoz exactly like this, with a shell on the box
-
And what does it show you? What if you do a traceroute to the ipv6 address.
Are you not resolving the ipv6 address, what is it using for the source.. Did you try setting the source in your ping command?
[2.4.4-RELEASE][root@sg4860.local.lan]/root: ping6 -H usage: ping6 [-DdfHmnNoqrRtvwW] [-a addrtype] [-b bufsiz] [-c count] [-g gateway] [-h hoplimit] [-I interface] [-i wait] [-l preload] [-P policy] [-p pattern] [-S sourceaddr] [-s packetsize] [-x waittime] [-X timeout] [hops ...] hostlets see the ifconfig from your wan showing your IPv6 info..
-
100% packet loss. Asterisks of doom.
I couldn't post the output here due to a spam alert...
https://pastebin.com/4RuqgCEH
-
prefixlen 128
Problem!
-
Really? I was talking to a guy yesterday and he had connectivity just fine with a prefixlen of 128. So why is it an issue?
-
Your gateway is outside your prefix - do you have a tunnel? /128 is the same as /32 in ipv4.. Its like a loopback address.. So yeah that is more than likely your problem.
Whats your route show you for your default?
-
Hmm OK. It was the same case for somebody else I was troubleshooting with yesterday, although their /128 for their WAN was even more different from their delegated subnet than mine is.
Having said that I cannot tr6 to my gateway...
My gateway is:
Destination Gateway Flags Netif Expire default fe80::d694:e8ff:fe1e:2b6b%vmx0 UG vmx0 $ traceroute6 to fe80::d694:e8ff:fe1e:2b6b (fe80::d694:e8ff:fe1e:2b6b) from fe80::20c:29ff:fee2:ebe8%vmx0, 64 hops max, 20 byte packets sendto: No route to host -
@deed02392 said in Can ping IPv6 from LAN but not from firewall itself:
Really? I was talking to a guy yesterday and he had connectivity just fine with a prefixlen of 128. So why is it an issue?
On IPv6, routing is normally done via link local addresses. A public address is not needed on the WAN interface, though may be used for testing etc.. A /128 prefix designates an interface only, which may be used internally for determining the interface to use for routing.
-
If your isp is handing you a /128 its for their internal use and not meant to be used for connectivity, etc..
What I can tell you /128 is not really valid and its same /32 in ipv4 world --- used for loopback interfaces, etc.. You can not route to them - they are good for firewall rules and access via the same layer 2, etc. etc..
That you would think you could route traffic off of it is -- contact your ISP to why they assign you a /128 if its suppose to be a global address..
-
I understand the concept of bitmasking on addresses. I just assumed that I would be able to route via the loopback address (presumably belonging to my ISPs switch) given out by DHCP, from this /128 I was also given.
One solution I can think of would be to give my firewall an address from the delegated /64, but how do I do this? My LAN network is tracking the WAN interface and that is where it seemingly magically gets its delegated /64. If that works, why doesn't my firewall get a working address?
-
You need to talk to your ISP..
-
What should I ask them? Because I have a feeling they are just going to tell me to contact the vendor of my third-party router. And that's what I'm here doing already.
-
FWIW, I have a /128 WAN address and can ping from the firewall. Packet capture shows the ping coming from that /128 address.
-
Right, so the simple fact my WAN has a /128 address isn't necessarily a problem. In which case it's hard to appreciate that there is a problem with my ISP that cannot be fixed with pfSense configuration. That's why I am here!
-
@johnpoz My ISP told me I have a /56. That's where one of the /64s that my LAN has came from.
Also, how does it make sense that my LAN can reach IPv6 internet when that connection would presumably have been routed by the firewall's configured gateway too?
-
@deed02392 said in Can ping IPv6 from LAN but not from firewall itself:
Right, so the simple fact my WAN has a /128 address isn't necessarily a problem. In which case it's hard to appreciate that there is a problem with my ISP that cannot be fixed with pfSense configuration. That's why I am here!
Try using Packet Capture to examine the outgoing pings and any result. I trust you're aware you have to use ping6 with pfSense, whereas with some Linux distros and Windows, the same ping command works for both IPv4 and IPv6.
-
I ran ping6 with packet capture. In the resultant capture I see ICMPv6 requests going back and forth between what looks like the gateway and me... but it does not show the failing ping6 requests to google.com that I shared above.
https://i.imgur.com/dIX2URS.png
In the process of trying different configuration options I seem to have broken IPv6 entirely, so I guess I'm done experimenting for now.
I guess there's no such thing as a simple setup of an IPv6 WAN. I thought I had it at enable DHCP6, set LAN to track WAN and then enable a DHCP6 server on LAN.
-
FWIW...
I am also with Hyperoptic (2a01:4b00::/32) and am seeing the exact same problem.
https://forum.netgate.com/topic/135917/ipv6-setup-with-hyperoptic-uk-ispMy setup is the same as yours:
-get a /56 PD
-get a /128 WAN address
-Link local IPv6 gateway
-cannot ping6 from pfSense box
-can ping out from LAN OK -
@deed02392 Did you need to clone the MAC address to even get IPv6 to work? I had to clone the MAC of the ZTE Hyperoptic router to get IPv6 to work at all.