Installing OpenBSD on XG-7100

stephenw10 · Apr 3, 2019, 12:22 PM

Hmm, like doesn't even run Coreboot?

When you add additional RAM it has to run a retraining process for it that can take some time. I'm not aware of needing to do that if you remove it again but personally I've never tried that.

You might try resetting the NVRAM so it retrains again. Set jumpers J10 and J11 to position 2-3 then power on the box. It will power up for a few seconds then power off. Remove the jumpers (or replace to 1-2) and power on again.

Steve

madapter · Apr 3, 2019, 1:23 PM

Our XG-7100 did not ship with jumpers but found 2, placed them on the J10 and J11 2-3 block. Did nothing it didn't get into coreboot (fan never turns off from high spin).

Are there any other headers of interest?

stephenw10 · Apr 3, 2019, 1:32 PM

Not for clearing the NVRAM.
With jumpers there on 2-3 I expect it to power on with fans at full for a few seconds then power off to indicate it has done the reset.
I assume you did that with the additional RAM removed? And adding the jumpers made no difference, that's the same behaviour you experienced just by removing the RAM?

Steve

madapter · Apr 3, 2019, 1:59 PM

Resetting it before removing the RAM got into core boot but it looks like I'm still halting in the same location.

root on rd0a swap on rd0b dump on rd0b
erase ^?, werase

What version of OpenBSD did you try this with and did you boot from a DVD or USB?

BTW Thanks for the help so far!

stephenw10 · Apr 3, 2019, 2:20 PM

I didn't, I have never tried it with OpenBSD. The point where it's stopping looks like the wrong console set as primary. That going entirely from FreeBSD experience but the fact it still shows device attach messages also indicates that.
In FreeBSD/pfSense we don't set anything beyond comconsole and the com speed. It may be necessary to set something else in OpenBSD.

Looks like you might have to edit /etc/ttys to actually get a login prompt there:
http://www.openbsd.org/faq/faq7.html#SerCon

Steve

madapter · Apr 3, 2019, 2:41 PM

Thanks, been through that at the start.

Is there another serial header on the board that we can use? If so can you provide the header block and the pinout info?

stephenw10 · Apr 3, 2019, 3:23 PM

SoC UART1 is in pins 3 and 4 of J2. But that's not the issue here the serial console is working for the boot output just not the interactive console. I'd double check /etc/ttys.

Steve

stephenw10 · Apr 3, 2019, 3:29 PM

Our development guys tell me that retraining for the RAM can take up to 10mins so that's likely the problem there. Just wait longer if you need to remove the RAM. Or to reinstall it if it has retrained without it.

Steve

madapter · Apr 10, 2019, 11:15 AM

Confirmed it varies but up to 10 minutes is what I'm seeing. I guess 5 minutes wait isn't enough sometimes. Still no luck in getting OpenBSD installed.

Rico · Apr 10, 2019, 11:17 AM

Wouldn't be FreeBSD the better choice to run on the XG-7100 anyway?

-Rico

madapter · Apr 10, 2019, 1:14 PM

It really comes down to what you're doing with the XG-7100. In general FreeBSD would be sufficient, but at the same time we're trying a few other OS to see what the limitations of the XG-7100 so that we can for production use under different scenarios.

float · Aug 16, 2020, 7:12 AM

Sorry to bump this topic. I'm also trying to install OpenBSD.

@madapter Does your system only have the eMMc 32GB or a m.2?

I noticed that OpenBSD does not detect the eMMc.

FreeBSD does:
mmcsd0: 31GB <MMCHC BJTD4R 0.3 SN D071F424 MFG 01/2018 by 21 0x0000> at mmc0 200.0MHz/8bit/8192-block
mmcsd0boot0: 4MB partition 1 at mmcsd0
mmcsd0boot1: 4MB partition 2 at mmcsd0
mmcsd0rpmb: 4MB partition 3 at mmcsd0

Could it be that because of the lack of detection of the eMMC, the system thinks it doens't have a HDD to install and thus does not show the install option?

stephenw10 · Aug 16, 2020, 11:04 AM

You are seeing exactly the same output?

It still looks like it's trying to use the VGA console to me.

Steve

float · Aug 16, 2020, 11:30 AM

Yes, but eMMc is not mentioned:

OpenBSD 6.7 (RAMDISK_CD) #177: Thu May  7 11:19:02 MDT 2020
    deraadt@amd64.openbsd.org:/usr/src/sys/arch/amd64/compile/RAMDISK_CD
real mem = 8562393088 (8165MB)
avail mem = 8298868736 (7914MB)
mainbus0 at root
bios0 at mainbus0: SMBIOS rev. 2.7 @ 0x7f6d7020 (7 entries)
bios0: vendor coreboot version "ADI_PLCC-01.00.00.11" date 01/08/2019
bios0: Silicom, Ltd. 80300-0134-g01
acpi0 at bios0: ACPI 3.0
acpi0: tables DSDT FACP SSDT MCFG TCPA APIC DMAR
acpimadt0 at acpi0 addr 0xfee00000: PC-AT compat
cpu0 at mainbus0: apid 4 (boot processor)
cpu0: Intel(R) Atom(TM) CPU C3558 @ 2.20GHz, 2195.39 MHz, 06-5f-01
cpu0: FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CFLUSH,DS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE,SSE3,PCLMUL,DTES64,MWAIT,DS-CPL,VMX,EST,TM2,SSSE3,SDBG,CX16,xTPR,PDCM,SSE4.1,SSE4.2,x2APIC,MOVBE,POPCNT,DEADLINE,AES,XSAVE,RDRAND,NXE,PAGE1GB,RDTSCP,LONG,LAHF,3DNOWP,PERF,ITSC,FSGSBASE,TSC_ADJUST,SMEP,ERMS,MPX,RDSEED,SMAP,CLFLUSHOPT,PT,SHA,IBRS,IBPB,STIBP,SENSOR,ARAT,XSAVEOPT,XSAVEC,XGETBV1,XSAVES
cpu0: 2MB 64b/line 16-way L2 cache
cpu0: cannot disable silicon debug
cpu0: apic clock running at 25MHz
cpu0: mwait min=64, max=64, C-substates=0.2.0.2, IBE
cpu at mainbus0: not configured
cpu at mainbus0: not configured
cpu at mainbus0: not configured
ioapic0 at mainbus0: apid 2 pa 0xfec00000, version 20, 24 pins, remapped
acpiprt0 at acpi0: bus 0 (PCI0)
acpiprt1 at acpi0: bus -1 (RP01)
acpiprt2 at acpi0: bus -1 (RP02)
acpiprt3 at acpi0: bus -1 (RP03)
acpiprt4 at acpi0: bus -1 (RP04)
acpiprt5 at acpi0: bus 2 (RP05)
acpiprt6 at acpi0: bus -1 (RP06)
acpiprt7 at acpi0: bus 3 (RP07)
acpiprt8 at acpi0: bus 4 (RP08)
acpicpu at acpi0 not configured
"PNP0C0C" at acpi0 not configured
"PNP0A08" at acpi0 not configured
"PNP0003" at acpi0 not configured
acpicmos0 at acpi0
"INTC3000" at acpi0 not configured
"BOOT0000" at acpi0 not configured
pci0 at mainbus0 bus 0
pchb0 at pci0 dev 0 function 0 "Intel C3000 Host" rev 0x11
pchb1 at pci0 dev 4 function 0 "Intel C3000 GLREG" rev 0x11
"Intel C3000 RCEC" rev 0x11 at pci0 dev 5 function 0 not configured
ppb0 at pci0 dev 6 function 0 "Intel C3000 PCIE" rev 0x11
pci1 at ppb0 bus 1
"Intel C3000 QAT" rev 0x11 at pci1 dev 0 function 0 not configured
ppb1 at pci0 dev 14 function 0 "Intel C3000 PCIE" rev 0x11
pci2 at ppb1 bus 2
ppb2 at pci0 dev 16 function 0 "Intel C3000 PCIE" rev 0x11
pci3 at ppb2 bus 3
ppb3 at pci0 dev 17 function 0 "Intel C3000 PCIE" rev 0x11
pci4 at ppb3 bus 4
"Intel C3000 SMBus" rev 0x11 at pci0 dev 18 function 0 not configured
ahci0 at pci0 dev 20 function 0 "Intel C3000 AHCI" rev 0x11: msi, AHCI 1.3.1
scsibus0 at ahci0: 32 targets
xhci0 at pci0 dev 21 function 0 "Intel C3000 xHCI" rev 0x11: msi, xHCI 1.0
usb0 at xhci0: USB revision 3.0
uhub0 at usb0 configuration 1 interface 0 "Intel xHCI root hub" rev 3.00/1.00 addr 1
ppb4 at pci0 dev 22 function 0 "Intel C3000 PCIE" rev 0x11
pci5 at ppb4 bus 5
ix0 at pci5 dev 0 function 0 "Intel X553 SFP+" rev 0x11: msi, address XX
ix1 at pci5 dev 0 function 1 "Intel X553 SFP+" rev 0x11: msi, address XX
ppb5 at pci0 dev 23 function 0 "Intel C3000 PCIE" rev 0x11
pci6 at ppb5 bus 6
ix2 at pci6 dev 0 function 0 "Intel X553 Backplane" rev 0x11: msi, address XX
ix3 at pci6 dev 0 function 1 "Intel X553 Backplane" rev 0x11: msi, address XX
"Intel C3000 ME HECI" rev 0x11 at pci0 dev 24 function 0 not configured
sdhc0 at pci0 dev 28 function 0 "Intel C3000 eMMC" rev 0x11: apic 2 int 16
sdhc0: SDHC 3.0, 200 MHz base clock
sdmmc0 at sdhc0: 8-bit, sd high-speed, mmc high-speed, dma
"Intel C3000 LPC" rev 0x11 at pci0 dev 31 function 0 not configured
"Intel C3000 PMC" rev 0x11 at pci0 dev 31 function 2 not configured
"Intel C3000 SMBus" rev 0x11 at pci0 dev 31 function 4 not configured
"Intel C3000 SPI" rev 0x11 at pci0 dev 31 function 5 not configured
isa0 at mainbus0
com0 at isa0 port 0x3f8/8 irq 4: ns16550a, 16 byte fifo
com0: console
com1 at isa0 port 0x2f8/8 irq 3: ns16550a, 16 byte fifo
sdmmc0: can't enable card
softraid0 at root
scsibus1 at softraid0: 256 targets
PXE boot MAC address 0XXXX, interface ix2
root on rd0a swap on rd0b dump on rd0b
WARNING: CHECK AND RESET THE DATE!
erase ^?, werase

stephenw10 · Aug 16, 2020, 1:52 PM

Nope seems to hang just at that point when it's writing out the install menu. Booting verbose is also no help. Google is failing me. Seems surprising no one else has hit this on other devices...

float · Aug 16, 2020, 4:05 PM

I tried to install with 6.7-current but still the same issue. Could it be that some hardware is not supported by OpenBSD?

>> OpenBSD/amd64 PXEBOOT 3.52
boot> stty com0 115200
boot> set tty com0
switching console to com0
                         >> OpenBSD/amd64 PXEBOOT 3.52
boot> bsd.rd
cannot open tftp:/etc/random.seed: No such file or directory
booting tftp:bsd.rd: 3826381+1573888+3882216+0+757760 [324033+128+468408+313269]=0xaa33b8
entry point at 0xffffffff81001000
                                 Copyright (c) 1982, 1986, 1989, 1991, 1993
        The Regents of the University of California.  All rights reserved.
Copyright (c) 1995-2020 OpenBSD. All rights reserved.  https://www.OpenBSD.org

OpenBSD 6.7-current (RAMDISK_CD) #27: Sat Aug 15 10:19:27 MDT 2020
    deraadt@amd64.openbsd.org:/usr/src/sys/arch/amd64/compile/RAMDISK_CD
real mem = 8562393088 (8165MB)
avail mem = 8298868736 (7914MB)
random: good seed from bootblocks
mainbus0 at root
bios0 at mainbus0: SMBIOS rev. 2.7 @ 0x7f6d7020 (7 entries)
bios0: vendor coreboot version "ADI_PLCC-01.00.00.11" date 01/08/2019
bios0: Silicom, Ltd. 80300-0134-g01
acpi0 at bios0: ACPI 3.0
acpi0: tables DSDT FACP SSDT MCFG TCPA APIC DMAR
acpimadt0 at acpi0 addr 0xfee00000: PC-AT compat
cpu0 at mainbus0: apid 4 (boot processor)
cpu0: Intel(R) Atom(TM) CPU C3558 @ 2.20GHz, 2195.40 MHz, 06-5f-01
cpu0: FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CFLUSH,DS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE,SSE3,PCLMUL,DTES64,MWAIT,DS-CPL,VMX,EST,TM2,SSSE3,SDBG,CX16,xTPR,PDCM,SSE4.1,SSE4.2,x2APIC,MOVBE,POPCNT,DEADLINE,AES,XSAVE,RDRAND,NXE,PAGE1GB,RDTSCP,LONG,LAHF,3DNOWP,PERF,ITSC,FSGSBASE,TSC_ADJUST,SMEP,ERMS,MPX,RDSEED,SMAP,CLFLUSHOPT,PT,SHA,IBRS,IBPB,STIBP,SENSOR,ARAT,XSAVEOPT,XSAVEC,XGETBV1,XSAVES
cpu0: 2MB 64b/line 16-way L2 cache
cpu0: cannot disable silicon debug
cpu0: apic clock running at 25MHz
cpu0: mwait min=64, max=64, C-substates=0.2.0.2, IBE
cpu at mainbus0: not configured
cpu at mainbus0: not configured
cpu at mainbus0: not configured
ioapic0 at mainbus0: apid 2 pa 0xfec00000, version 20, 24 pins, remapped
acpiprt0 at acpi0: bus 0 (PCI0)
acpiprt1 at acpi0: bus -1 (RP01)
acpiprt2 at acpi0: bus -1 (RP02)
acpiprt3 at acpi0: bus -1 (RP03)
acpiprt4 at acpi0: bus -1 (RP04)
acpiprt5 at acpi0: bus 2 (RP05)
acpiprt6 at acpi0: bus -1 (RP06)
acpiprt7 at acpi0: bus 3 (RP07)
acpiprt8 at acpi0: bus 4 (RP08)
acpicpu at acpi0 not configured
"PNP0C0C" at acpi0 not configured
acpipci0 at acpi0 PCI0: 0x00000000 0x00000011 0x00000001
"PNP0003" at acpi0 not configured
acpicmos0 at acpi0
"INTC3000" at acpi0 not configured
"BOOT0000" at acpi0 not configured
pci0 at mainbus0 bus 0
pchb0 at pci0 dev 0 function 0 "Intel C3000 Host" rev 0x11
pchb1 at pci0 dev 4 function 0 "Intel C3000 GLREG" rev 0x11
"Intel C3000 RCEC" rev 0x11 at pci0 dev 5 function 0 not configured
ppb0 at pci0 dev 6 function 0 "Intel C3000 PCIE" rev 0x11
pci1 at ppb0 bus 1
"Intel C3000 QAT" rev 0x11 at pci1 dev 0 function 0 not configured
ppb1 at pci0 dev 14 function 0 "Intel C3000 PCIE" rev 0x11
pci2 at ppb1 bus 2
ppb2 at pci0 dev 16 function 0 "Intel C3000 PCIE" rev 0x11
pci3 at ppb2 bus 3
ppb3 at pci0 dev 17 function 0 "Intel C3000 PCIE" rev 0x11
pci4 at ppb3 bus 4
"Intel C3000 SMBus" rev 0x11 at pci0 dev 18 function 0 not configured
ahci0 at pci0 dev 20 function 0 "Intel C3000 AHCI" rev 0x11: msi, AHCI 1.3.1
scsibus0 at ahci0: 32 targets
xhci0 at pci0 dev 21 function 0 "Intel C3000 xHCI" rev 0x11: msi, xHCI 1.0
usb0 at xhci0: USB revision 3.0
uhub0 at usb0 configuration 1 interface 0 "Intel xHCI root hub" rev 3.00/1.00 addr 1
ppb4 at pci0 dev 22 function 0 "Intel C3000 PCIE" rev 0x11
pci5 at ppb4 bus 5
ix0 at pci5 dev 0 function 0 "Intel X553 SFP+" rev 0x11, msix, 1 queue, address xx
ix1 at pci5 dev 0 function 1 "Intel X553 SFP+" rev 0x11, msix, 1 queue, address xx
ppb5 at pci0 dev 23 function 0 "Intel C3000 PCIE" rev 0x11
pci6 at ppb5 bus 6
ix2 at pci6 dev 0 function 0 "Intel X553 Backplane" rev 0x11, msix, 1 queue, address xx
ix3 at pci6 dev 0 function 1 "Intel X553 Backplane" rev 0x11, msix, 1 queue, address xx
"Intel C3000 ME HECI" rev 0x11 at pci0 dev 24 function 0 not configured
sdhc0 at pci0 dev 28 function 0 "Intel C3000 eMMC" rev 0x11: apic 2 int 16
sdhc0: SDHC 3.0, 200 MHz base clock
sdmmc0 at sdhc0: 8-bit, sd high-speed, mmc high-speed, ddr52, dma
"Intel C3000 LPC" rev 0x11 at pci0 dev 31 function 0 not configured
"Intel C3000 PMC" rev 0x11 at pci0 dev 31 function 2 not configured
"Intel C3000 SMBus" rev 0x11 at pci0 dev 31 function 4 not configured
"Intel C3000 SPI" rev 0x11 at pci0 dev 31 function 5 not configured
isa0 at mainbus0
com0 at isa0 port 0x3f8/8 irq 4: ns16550a, 16 byte fifo
com0: console
com1 at isa0 port 0x2f8/8 irq 3: ns16550a, 16 byte fifo
umass0 at uhub0 port 2 configuration 1 interface 0 "Sony Storage Media" rev 2.00/1.00 addr 2
umass0: using SCSI over Bulk-Only
scsibus1 at umass0: 2 targets, initiator 0
sd0 at scsibus1 targ 1 lun 0: <Sony, Storage Media, 0100> removable serial.054c0439008123001204
sd0: 7740MB, 512 bytes/sector, 15851520 sectors
sdmmc0: can't enable card
softraid0 at root
scsibus2 at softraid0: 256 targets
PXE boot MAC address xx, interface ix2
root on rd0a swap on rd0b dump on rd0b
erase ^?, werase

stephenw10 · Aug 16, 2020, 4:13 PM

For some reason the installer is hanging at that point. I have no idea why. It seems to be uncommon, I can find no other similar reports.

Using OpenBSD on the XG-7100 is going to be pretty restricted anyway even you do get it installed. You would only be able to use the SFP ports or anything in the expansion slot.

Steve

float · Aug 16, 2020, 4:15 PM

I also tried to install Freebsd 12.1 via the serial console. That worked like a charm after doing "set kern.vty=sc" :-)

stephenw10 · Aug 16, 2020, 4:17 PM

Yes, I would expect it to. It's odd that the OpenBSD installer freezes at that point. If there were some reason for it I would expect to see a load of similar reports on other hardware.

float · Aug 17, 2020, 7:01 PM

Could you help me out on how to configure Marvell 88E6190? I only see ix0 ix1 ix2 ix3. They don't detect any UTP-cable.