adding link to my shop
-
Yes I do have VLANs in the shop (Guest), and an IOT one, similar to my home.
Yes I am using 192.168.1.0 behind the shop router and at the house. This was my original concern.
The primary LAN is not a vlan so I remove the V on that in the picture. The router/firewall in the shop is a Netgear router running Tomato.
I originally setup the link between the house and the shop as a subnet 10.10.1.0/24, and I could get to the nano beams, but couldn't get the shop to route to the internet. When I changed it to a VLAN I could get routing to the internet, but lost routing to the nano-beams.
John, I have no idea what your last paragraph is saying. " source nat traffic to them from one of the locations that is not their default route, if you can not setup routing on the devices.", but like the conclusion.
thanks again,
david -
So your wifi devices 30.115 and 30.116 devices what do they have set for their gateway? Do they have one.. While I have to assume your tomato is natting, which means you wouldn't be able to get to stuff in the shop because its firewalled and you would have to port forward to get to stuff behind your shop firewall.
So while you would be able to get to the devices from shop network because to the wifi devices you would be coming from shop firewalls IP in the 192.168.30 network... From your house side.. They wouldn't know how to talk to some other network, etc..
Your current design with a firewall in shop complicates the setup.. But can be configured to do whatever you want to do, not sure about tomato and its limited feature set... But would assume you can disable nat on specific interfaces?
-
The shop router DHCPs and an IP from the home router, it happened to get 192.168.30.3. I can easily make that as static IP if it makes things easier.
This is what is set as the gateway for the shop devices.
My home devices get the gateway assigned to the igb2 interface, which is my static IP address.
I don't need access to the shop devices from the home, but I would like to get access to the nano-beams. I can see that my home firewall passes the requests to the 192.168.30.0 vlan, but I get no response back. Ping just says no response.
I'd love to be able to remove the double NAT if possible.
thanks
david -
If I just bridge my WAN to my shop_link, then have the router in the shop do everything, does the bridge impact my other interfaces, or does the bridge only impact the interfaces in the bridge.
I don't want my LAN interface bridged to my WAN.
thanks
-
@lovingHDTV said in adding link to my shop:
I'd love to be able to remove the double NAT if possible.
Then do so - why do you think you need this tomato doing nat? Just use it as an AP in your shop put everything on vlan on pfsense in your home = done!
My drawing from before.
-
@johnpoz I don't want to merge the two networks.
-
YOUR NOT!!!! It will be its own vlan!!
If you want to still leverage your T1 you could still do that.. And your home could even use it, since you have an L2 network connecting your home and shop via the wifi devices.
So now not only would you shop have a failover network with your T1, you could even use it for your home network if your home wan goes out.
Your wifi bridge setup is like a wire that runs from your home to your shop... Worse case scenario is if home network goes out, then traffic from shop to your T1 would be going over your wifi to hose connection twice, ie a hairpin.. But since its a T1, and slow as shit, that wouldn't be an issue ;)
-
@johnpoz OK I'm confused :)
My shop is on the 192.168.1.0 subnet and so is my LAN. I basically created them both the same way.
I created a 192.168.30.0 VLAN to get to my shop. If I remove the tomato router, or change it to an AP, that would change my shop to 192.168.30.0 right? So I would have to change everything to that subnet instead of 192.168.1.0. I would also have to manage everything in my shop from pfsense, and I was hoping to keep everything separate.
david
-
OMG dude they would be separate.. But yeah you would need to use 2 different IP schemes.. If you want to use 192.168.1 in your shop, and you also want to use 192.168.1 in your house - then you would have to double NAT.. Or you make them the same network and just bridge for firewall between them..
Or just simply change one of the IP ranges.. Use 192.168.X in your house, use 192.168.Y in your shop..
-
@johnpoz OK thanks.
