How to get 2 separate networks to talk to each other?

johnpoz

Well makes no sense at all... Do you have another interface you can use? Another cable.. Post a ifconfig output on pfsense. If it was a bad cable - you would think you wouldn't see the traffic too pfense, and you would see traffic out even if didn't get to the client when you sniff when you pinged.

ilovechickennuggets

@johnpoz
ifconfig

I do have one more open interface and 1 extra cable. Let's call it a day for now and maybe try some other time and set up the rules and etc for new interface.

Thank you both for your time today! @kiokoman

johnpoz

dude... How do you have 192.168.70.1 on igb2, and you also have it on igb1.70??

Pfsense shouldn't even let you do that - because the interfaces overlap!!

Yeah that is not going to work ;)

ilovechickennuggets

@johnpoz
igb1.70 is a vlan right? That was deleted sometime ago and doesn't exist currently? Here's all of the vlans as of now:

johnpoz

But the interface is still there via your ifconfig - so yeah that not going to work ;)

I would check in your xml - forwhatever reason its still there.. So yeah big issue!

ilovechickennuggets

@johnpoz
Nice! How do I get rid of it cleanly? This doesn't actually show up on my GUI. I have routine XML backups so doing it through XML shouldn't be a problem.

johnpoz

I would look in your xml to see if its stuck in their somehow.. Then you could remove it from the xml and then reload.. Then do a reboot to validate it goes away.

You could remove it from cli command - but if its stuck in some xml, then on a reboot it could get put back.

I thought I was going nuts - cuz it sure didn't make sense. But now seeing you have 2 interfaces with the same IP makes sense that it was sending traffic out the other interface - or trying ;) So yeah our symptoms make sense for this sort of issue.

ilovechickennuggets

@johnpoz
Oh so I can just go through xml and delete all lines related to igb1.70? Just to be clear on the correct way:

Delete igb.70 from xml
Restore new xml
Reboot and check xml again

johnpoz

Yeah must be something left in the xml I would think... Or maybe the interface just didn't get delete.. But I have to assume you have rebooted at some point in troubleshooting this.

So I take it something must be messed up in the xml.

So validate its not in there in some messed up way.. If it is, remove it and then restore it. And then either delete the interface with cli, or reboot and make sure that igb1.70 interface is not there.

ilovechickennuggets

@johnpoz
So I looked through the entire XML file line by line and also with search function using any combinations of igb1, igb1.70, 70, and igb. Igb1.70 or even vlan 70 does not exist in the XML file at all anywhere. I ran ifconfig and it does still indeed show up. Thoughts on maybe something I missed?
This is the only group of igb.X in the entire XML file.

johnpoz

did you look for the IP? Do a search. Search for interface igb1.70 as well..

If your saying its not in the xml, have you actually rebooted since you removed it - and it still comes back via ifconfig?

example - here is where the interface is created

		<opt5>
			<descr><![CDATA[W_PSK]]></descr>
			<if>igb2.4</if>
			<spoofmac></spoofmac>
			<enable></enable>
			<ipaddr>192.168.4.253</ipaddr>
			<subnet>24</subnet>

For 1 of my vlans... On your interface tab in pfsense - do you see the inteface still there? Even if you removed the vlan?

ilovechickennuggets

@johnpoz
Like this right?

johnpoz

So you don't see that that is listed on your ifconfig output anywhere in the xml? You searched for it? You searched for igb1.70 Not just scroll through?

And again - have you actually rebooted since you removed this vlan? And your not seeing that IP or interface anywhere in the xml?

ilovechickennuggets

@johnpoz
Yup not found anywhere even with search function. I'll be back for reboot...

ilovechickennuggets

@johnpoz
Very good! The halt and reboot removed 70 from ifconfig. I got to head out now and continue at a later time.

ilovechickennuggets

@johnpoz I plugged in my NAS and everything works just like before as expected. I also learned some new things along the way. Thank you so much for your help! I really appreciate your patience with me.

johnpoz

Glad you got it sorted - was an odd one... The hard part is getting the info needed, you were very helpful in giving us the info requested.. Which many users it can be like pulling teeth ;)

Come on back if you have further questions!

kiokoman

nice !